HomeMy WebLinkAbout3405 Whippoorwill Ct 17-427; ROOFCITY OF SANFORDFECEIVINBUILDING & FIRE PREVENTION
PERMIT APPLICATION
Y.
Application No:
Documented Construction Value: S 9,370.00
Job Address: 3405 WHIPPOORWILL CT SANFORD, FL 32773
Historic District: Yes No El
Parcel ID: 07-20-31-512-0000-0030
ResidentialEl Commercial Roof Replacement
Type of Work: New Addition Alteration Repair Demo Change of Use Move
Description of Work: Roof Replacement- IKO Cambridge Asphalt Shingles - 25 squares
Plan Review Contact Person:
Phone: 321-441-2300
Justin Shelton Title: R/R Manager
321-441-2313Fax: Email' swilliams@collisroofing.com
Property Owner Information
Name Christina TaylorPhone: 407-430-5581
Street: 3405 WHIPPOORWILL CT SANFORD, FL 32773
Resident of property?
City, State Zip:
Contractor Information
Name Collis Roofing, Inc. Phone: 321-441-2300
Street: P.O. Box 520668, Longwood, FL. 32752
Fax: 321-441-2313
City, State Zip: State License No.: CCCO58022
Architect/Engineer Information
n/a
Name: Phone:
Street: Fax:
City, St, Zip: E-mail:
Bonding Company:
Address:
n/a Mortgage Lender:
Address:
n/a
WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR
PAYING . TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE
RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN
FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF
COMMENCEMENT.
Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has
commenced prior to the issuance of a permit and that all work will be performed to meet standards of all laws regulating construction
in this jurisdiction. I understand that a separate permit must be secured for electrical work, plumbing, signs, wells, pools,
furnaces, boilers, heaters, tanks, and air conditioners, etc.
FBC 105.3 Shall be inscribed with the date of applicatlon and the code in effect as of that date: 51h Edition (2014) Florida Building Code
Revised: June 30, 2015 Permit Application
A t uq, GS
NOTICE: In addition to the requirements of this permit, there may be additional restrictions applicable to this property that may befoundinthepublicrecordsofthiscounty, and there may be additional permits required from other governmental entities such as water
management districts, state agencies, or federal agencies.
Acceptance of permit is verification that I will notify the owner of the property of the requirements of Florida Lien Law, FS 713
The City of Sanford requires payment of a plan review fee at the time of permit submittal. A copy of the executed contract is required
in order to calculate a plan review charge and will be considered the estimated construction value of the job at the time of submittal.
The actual construction value will be figured based on the current ICC Valuation Table in effect at the time the permit is issued, in
accordance with local ordinance. Should calculated charges figured off the executed contract exceed the actual construction value,
credit will be applied to your permit fees when the permit is issued.
OWNER'S AFFIDAVIT: I certify that all of the foregoing information is accurate and that all work will
be done in compliance with all applicable laws regulating construction and zoning.
Signature of Owner/Agent Date
Print Owner/Agent's Name
Signature of Notary -State of Florida Date
Owner/Agent is Personally Known to Me or
Produced ID Type of ID
600111ao
Signa re of Co actor/Agent Date
J. Douglas L ier
Print Cont to ent's N
I S
RY F'UB i STEPHANIE J. WILLIAMS
Notary Public - State of Florida
Commission # GG 008373
OFF My Comm. Expires Oct 29, 2020
Produced ID Type of ID
BELOW IS FOR OFFICE USE ONLY
Permits Required: Building Electrical
Construction Type:
Total Sq Ft of Bldg:
to Me or
Mechanical Plumbing Gas[] Roof
Occupancy Use: Flood Zone:
Min. Occupancy Load: # of Stories:
New Construction: Electric - # of Amps Plumbing - # of Fixtures
Fire Sprinkler Permit: Yes No # of Heads
APPROVALS: ZONING:
ENGINEERING:
COMMENTS:
Revised: June 30, 2015
Fire Alarm Permit: Yes No
UTILITIES: WASTE WATER:
Fes: BUILDING:
Permit Application
1/30/2017
0040 Johnson, CFA
PACER
Parcel Information
SCPA Parcel View: 07-20-31-512-0000-0030
Property Record Card
Parcel: 07-20-31-512-0000-0030
Owner: WHITE CHRISTINA
Property Address: 3405 WHIPPOORWILL CT SANFORD, FL 32773
Value Summary
Parcel 07-20-31-512-0000-0030
Owner WHITE CHRISTINA
Property Address 3405 WHIPPOORWILL CT SANFORD, FL 32773
Mailing 3405 WHIPPOORWILL CT SANFORD, FL 32773
Subdivision Name WHIPPOORWILL
Tax District S1-SANFORD
DOR Use Code 01 -SINGLE FAMILY
Exemptions 00-HOMESTEAD(2008)
In
Seminole County GIS
Legal Description
LOT 3
WHIPPOORWILL
PB 40 PG 60
Taxes
Tax Amount without SOH: $3,172.89
2016 Tax Bill Amount $1,995.71
Tax Estimator
Save Our Homes Savings: $1,177.18
Does NOT INCLUDE Non Ad Valorem Assessments
Taxing Authority
2017 Working
Values
2016 Certified
Values
Valuation Method Cost/Market Cost/Market
Number of Buildings 1 1
Depreciated Bldg Value 173,375 165,859
Depreciated EXFT Value
141,115 50,000
Land Value (Market) 33,000 33,000
Land Value Ag
91,115
County General Fund
Just/Market Value ** 206,375 198,859
Portability Adj
25,000 Yes
Save Our Homes Adj 65,260 58,725
Amendment 1 Adj
1754 294,500
P&G Adj 0 0
Assessed Value 141,115 140,134
Tax Amount without SOH: $3,172.89
2016 Tax Bill Amount $1,995.71
Tax Estimator
Save Our Homes Savings: $1,177.18
Does NOT INCLUDE Non Ad Valorem Assessments
Taxing Authority Assessment Value Exempt Values Taxable Value
Page
Schools 141,115 25,000 116,115
City Sanford 141,115 50,000 91,115
SJWM(SaintJohns Water Management) 141,115 50,000 91,115
County Bonds 141,115 50,000 91,115
County General Fund 141,115 50,000 91,115
Sales
Description Date Book Page Amount Qualified Vac/Imp
WARRANTY DEED 8/1/2007 06812 0927 268,000 Yes Improved
WARRANTY DEED 11/1/2001 04347 0502 179,000 Yes Improved
WARRANTY DEED 3/1/2001 04021 1773 25,000 Yes Vacant
WARRANTY DEED 8/1/1999 03707 1754 294,500 No Vacant
WARRANTY DEED 12/1/1997 03343 1158 320,000 No Vacant
SPECIAL WARRANTY DEED 12/1/1992 02522 1923 351,000 No Vacant
CERTIFICATE OF TITLE 11/1/1991 02356 1758 311,200 No Vacant
Find Comparable Sales
Land
MethodFrontage Depth Units Units Price Land Value
LOT I 0.00 I 0.00 1 1 I $33,000.00 33,000
http://parceidetail.scpafl.org/ParcelDetail lnfo.aspx?PID=07203151200000030 1/2
LIMITED POWER OF ATTORNEY
Altamonte Springs, Casselberry, bake Mary, Longwood, Sanford,
Seminole County, Winter Springs
Date: 2/10/2017
I hereby name and appoint: Ray Henderson
an agent of: Collis Roofing, Inc.
Name of Company)
to be my lawful attorney-in-fact to act for me to apply for, receipt for, sign for and do all things
necessary to this appointment for (check only one option):
The specific permit and application for work located at:
3405 WHIPPOORWILL CT SANFORD, FL 32773
Street Address)
Expiration Date for This Limited Power of Attorney:
License Holder Name: J. Douglas Lanier
State License Number: CCC058022 ^
Signature of License Holder:
STATE OF FLORIDA
COUNTY OF Seminole
The foregoing instrument was acknowledged before me this 10 day of February
200 17 , by J. Douglas Lanier who is 0 personally known
to me or who has produced as
identification and who did (did not) t oath. /
Notary Seal) Stephanie J. Williams
Print or type name
Notary Public - State of Florida
Commission No.
My Commission Expires:
y"„ aY P.e`
NotarySTEPHANIE J. WILL
Rev. 08.12) = ,oP CoPublic - State of Florida
M
mission # GG 00837YC
Expires Oct 29, 2020
02/08/2017 11:04
Department of Health • Vital Statistics
STATE OF FLORIDA
MARRIAGE RECORD
TYPE IN UPPER CASE
USE BLACK INK
Thls license not valla unlasa seal of Clerk,
Circuit or County Ooun, aDoears thereon.
12-439
APPLICATION. NUMBER)
TAX) P.0021002
STATE FILE NU R
MARYANNE MORSE, CLERK OF CIRCUIT COURT
SEMI MOLE COUNTY
BA 97775 Pg 0399; Upg)
CLERK' S # 2012®59606
RECORDED 631/1/2012 04:14:34 Pill
RECORDING FEES ®.00
RECORDED BY J Eckenroth(all)
ROBERT WILLIAM TAYLOR October 8, 1951
Sa. RESIDENCE - CITY,MOWN, OR LOCATION 3D. COUNTY 3C. STATE -' 4, BIRTNPtACE (Sid's or Fore;$
734 SIFFORo CT SEMINOLE FLORIDA 32746 FLORIDALAKEMARY
s OC'S N',ti1,E`-rF.m AF+d b; Las[}.. .. ... •- O.ifR E'' ) - ... L. V A:7E\" 'NAM (7ld;fl'eran. ^ -' S. DA, 0 B RTH'(Ma;th: Day
CHRISTINA SUSAN WHITE DRISCOLL April 12, 1967
o. RESIDENCE •CITY. TOWN, OR LOCATION 70, COUNTY 7c. STATE B. BIRTHPLACE (9lele 0 -Pore,%
3405 WHIPPOORWILL C7 SEMINOLE FLORIDA 32773 FLORIDA
wE THE APPLICANTS NAMED IN THI$ CERTIFICATE, EACH FOR HIMSELF OR HERSELF, STATE THAT Tne INFORMA nQN PROVIDED
ON THIS RECORD IS CORRECT TD THE BEST OF OUR KNOWLEDGE AND BEUEF, THAT NO LEGAL OBJECTION TO THE MARRIAGE
NOR THE ISSUANCE OF A LICENSE TO AUTHORIZE THE SAME IS KNOwN TO US AND HEAe9Y APPLY FOR UCEN99 TO MARRY.
9. SIGNATURE Or (BROOM tge.NUneme 'n I kv7 ;D, SUBSCRIBED AND SWORN TO BEFORE ME ON (DATE)
r C ",% >/.. V - April 012
C ......ti.
i • °' 11. TITLE OF OFFICIAL'-'
DEPUTY CLERK :
TNII QFFICIAL(Uaebfxklnk)
B•, ,Kr i3. SI&TO s'yn lull n DI k fnlq 1 SU CRIBIDAND SWORN TO BEFORE ME ON (DATE) 3 ,
01215S _-
7 9if3 F OFFICUIL (We bleckin4 ....
DEPUTY CLERK
LICENSE T AR'RY
AU RANY PERSON DULY AUTHORIZED BY THE W"S OF .t+ I• 54•- ..! 9 1 IZATIQN ANO LICE S HEREBY GIVEN TO E STATE OF PENiIDA Tp PERFORM
A MARRIAGE CEREMONY W'THIN YnE STATE OF FLORIDA ANC TO SOLEMNIZE THE MARRIAGE OR THE ABOVE NAMED PFRSONS. THIS LICENSE MUST
BE USED ON OR AFTER THE EFFECTIVft DATE AND ON OR BEFORE THE EXPIRATION DAT-. IN THE STATE OF FLOR)OA IN ORDER TO Be RECORDED AND VALI
A+p i7 COUIv'r'r 138UING LICENSE 18. DATE LICONSE I65U D 191. DATE LICENSE EFFECTIVE119.EXPIRATIONOATEe A
SEMIN LE Aril 24 2012. .. p __ April 27, 2012 June 23, 2012
261. SiGNATU URTCLERKORJUOGE 20t), TITLE 2DC. BY D.C.
MARN SE, CLERK OF CIRCUIT COURTDEPUTY CLERK TH0- BY: / D.C.
Z1. DATE OF MARRIAGtAdon(7L
DeBGvEk
flit ORQOM CN - - 0 D BRiBe'wegB JOYni-cD BY MF IN'MARRIAGE W ACCORDANCE WITH THE LOWS OF THE STATE OF FLORIDA,
TY. TOWN, OR LOCATION OF MAAARIAGE
MAY 18, 2012 SANFORD
23a, 51 NATURE OF'PERS N P RFOR I G CEREMONY (Uso blacklnq 23c ADDRESS (OfjoemonpCrlorniW csremony)
Js a 01 N. PARK AVENUE, SANFORD, FL 32771
lob. NAME AND TITLE OF PERSON PERFORMING CEREMONY 24, SIGNATURE OF
I S t' IOC •na'r ao.nal
KIM HAIL, DEPUTY CLERK TO CEREMONY (Usc b)aCA IND
s .Sr AX Y A_ k ,
i ;L£t.l# cnc&
COLLIS ROOFING, INC.
P.O. Box 520668
Loogr/ood, FL 32752-0668
Pb. (321)141-2300
Fax (321) 441-2313
Lie: # CCCO53022
Date: 1/9/2017 I Phone; 407-430-5581
Attention: Tina Taylor Email: tinawalkergrant@bellsouth.net
Job ;3405 Whippoorwill Ct
Address: Sanford, FL 32773
Collis Roofing, Inc. proposes to supply the labor and materials necessary to apply your roofing as follows:
A) Remove old shingles.and underlayment to bare deck and dispose of properly.
B) Replace 10 sheets ofexisting decking.
C) Inspect existing decking for water damage and re -nail per code. We will remove and replace at a rate of 565.00 per sheet
ofplywood or $5.00 per linear foot Cedar facia 58.00 per linear foot. (Note: This amount is p9t included in the total
below).
D) Collis Roofing. Inc. will provide all applicable permits.
1. Supply and install code approved Rhino U20 Synthetic underlayment to deck using simplex nails.
2. Supply and install code approved 2 VT galvanized painted cave drip and secure to the roof deck with nails
around all eaves and rakes (Please'specrfy drip edge color .;9 "Gt NCS'
3. Secure the cave metal with mastic and then apply IKO Starter shingles at all eaves with the seal strip at the
edge of the roof.
4. Supply and install all synthetic flashings for plumbing penetrations.
5. Supply and install color matched kitchen and bath exhaust vents,
6. Supply and IKo Ilia and Ride shingles as required by manufacturers warranty.
7. Supply and install code approved shingled over ridge vents as required.
8. Supply and install code approved Midstates self -adhered underlayment and preformed 26ga,galvanized metal
along all valleys per manufacturer specifications.
9. Supplyand install 1 Cambridse _shingles per manufacturer's specifications and all applicable building
codes il'l 5
sP fy stiingle color_. - `. ' -• ""'"7
10 Collis Roofing Inc. will supply 95yfarfull coverage warranty upon completion.
A manufacturer's warranty shall be fiunished if called for above. The above work shall be performed in a substantial'workmanlike
manner for the sum of:
IKO Cambridge Lifetime 130 mpb - $9,370.00
With payment to be made as follows: 50% on commencement, 50% upon completion.
Respectfullysubmitted: Eddie Coad
Date: r yZ 1,IltV, Approved By: r C
Collis Roofing, Inc.
ACCORDING TO FLORIDA'S CONSTRUCTION LIEN LAW (SECTIONS 713.001-713.37, FLORIDA STATUTES),
THOSE.WHO WORK ON YOUR PROPERTY OR`PROVIDE MATERIALS'AND ARE" NOT PAID IN FULL RAVE A
RIGHT TO ENFORCE THEIR CLAIM FOR PAYMENT AGAINST YOUR PROPERTY. IF YOUR CONTRACTOR
OR A SUBCONTRACTOR FAILS TO PAY SUBCONTRACTORS, SUB -SUBCONTRACTORS, OR MATERIAL,
SUPPLIERS, THE PEOPLE WHO ARE OWED MONEY MAY LOOK TO YOUR PROPERTY FOR PAYMENT, EVEN
IF YOU. HAVE ALREADY PAID YOUR CONTRACTOR IN FULL IF YOU FAIL TO PAY YOUR CONTRACTOR,
YOUR CONTRACTOR MAY ALSOMAVE A LIEN ON YOUR PROPERTY. THIS MEANS IF A LIEN IS FILED
YOUR PROPERTY COULD BE SOLD AGAINST YOUR WILL TO PAY FOR LABOR, MATERIALS, OR OTHER
SERVICES THAT YOUR CONTRACTOR OR A SUBCONTRACTOR MAY HAVE FAILED TO PAY. TO PROTECT
YOURSELF, YOU SHOULD STIPULATE IN TMS CONTRACT'THAT BEFORE ANY PAYMENT IS MADE, YOUR
CONTRACTOR IS REQUIRED TO PROVIDE.YOU WITH A WRITTEN RELEASE OF LIEN FROM ANY PERSON
UR COMPANY THAT HAS PROVIDED TO YOU A "NOTICE TO OWNER." FLORIDA'S CONSTRUCTION LIEN
LAW IS COMPLEX AND IT IS RECOMMENDED THAT YOU CONSULT AN ATTORNEY. /
Page 1 of 3 1
2/10/2017 Florida Building Code Online
ti
x
BCIS Home Log In ( User Registration ( Hot Topics Submit Surcharge Stats & Facts Publications FBC Staff BCIS Site Map Links i Search
Florida
1 0-m- Product Approval
USER: Public User
T hlcrv_raJ Ixt.A',^m
Product Approval Menu > Product or Application Search > Application List > Application Detail
FL # FL7006-R9
Application Type Revision
Code Version 2014
Application Status Approved
Approved by DBPR. Approvals by DBPR shall be reviewed and ratified
by the POC and/or the Commission if necessary.
Comments
Archived
Product Manufacturer IKO Industries, Ltd
Address/Phone/Email 40 Hansen Road South
Brampton, NON -US L6W 3H4
708) 496-2800 Ext 200
rmetzOO1@tampabay.rr.com
Authorized Signature Robert Metz
rmetzOO1@tampabay.rr.com
Technical Representative Bob Metz
Address/Phone/Email REMCO of Pinellas
456 Avila Circle NE
Saint Petersburg, FL 33703
727) 776-5261
rmetzOO1@tampabay.rr.com
Quality Assurance Representative Don Shaw
Address/Phone/Email IKO Industries LTD
120 Hay Rd.
Wilmington, DE 19808
717) 579-6706
don.shaw@iko.com
Category Roofing
Subcategory Asphalt Shingles
Compliance Method Certification Mark or Listing
Certification Agency FM Approvals - CER
Validated By Locke Bowden
i; Validation Checklist - Hardcopy Received
Referenced Standard and Year (of Standard) Standard Year
ASTM D3161 modified to 110 mph 2009
ASTM D3462 2009
ASTM D7158 Class H 2008
ASTM E108 2007
Equivalence of Product Standards
Certified By
http://www.floridabui Idi ng.org/pr/pr_app_dtl.aspx?param=wGEVXQwtDgse7mYBd2b3K6mXtoZLhN VX122N pl70J 1 E%3d 1/3
2/10/2017 Florida Building Code Online
Product Approval Method Method 1 Option A
Date Submitted 06/28/2015
Date Validated 06/30/2015
Date Pending FBC Approval
Date Approved 07/06/2015
Summary of Products
FL # Model, Number or Name Description
7006.1 Cambridge, Cambridge HD and CRC Laminated architectural fiberglass asphalt shingle
Biltmore AR manufactured at IKO's Kankakee, IL; Hawkesbury, Ont.;
Wilmington, DE; Sylacauga,AL and Toronto, Ont. plants
Limits of Use Certification Agency Certificate
Approved for use in HVHZ: Yes FL7006 R9 C CAC FM Letter - ASTM d3161 letter - 4 -15 -
2015 .pdf
FL7006 R9 C CAC FM Letter - ASTM d3462 letter - 5 6
Approved for use outside HVHZ: Yes
Impact Resistant: N/A
15.odf
FL7006 R9 C CAC FM Letter - ASTM E 108 letter - 5 3
Design Pressure: N/A
Other:
15 .odf
Quality Assurance Contract Expiration Date
12/31/2020
Installation Instructions
FL7006 R9 II IKO-133-02-01 Letter - Installation
Instructions for FBC FL7006.odf
Verified By: Duc T Nguyen 65034
Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
7006.2 Hip and Ridge 12 Cap fiberglass This is a 12" x 12" fiberglass asphalt shingle used to cover
shingles the hip and/or ridge of an asphalt shingle roof system
manufactured in Toronto, Ont. and Brampton, Ontario
Limits of Use Certification Agency Certificate
Approved for use„in HVHZ: Yes FL7006 R9 C CAC FM Letter - ASTM d3161 letter - 4 -15 -
2015 .pdf
FL7006 R9 C CAC FM Letter - ASTM d3462 letter - 5 6
Approved for use outside HVHZ: Yes
Impact Resistant: N/A
15.odfDesignPressure:' N/A
Other: FL7006 R9 C CAC FM Letter - ASTM E 108 letter - 5 3
15 .pdf
Quality Assurance Contract Expiration Date
12/31/2020
Installation Instructions
FL7006 R9 II Hip and Ridge Cap Shingle Installation
Instructions.pdf
FL7006 R9 II IKO-133-02-01 Letter - Installation
Instructions for FBC 171-7006.0f
Verified By: Duc T Nguyen PE 65034
Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
7006.3 Leading Edge Plus Asphalt Shingle One piece fiberglass asphalt shingle used as a starter strip at
Starter Strip the bottom of a roof system manufactured in Brampton and
Hawkesbury, Ontario plants
Limits of Use Certification Agency Certificate
Approved for usei,in'HVHZ: Yes
Approved for use outside HVHZ: Yes
FL7006 R9 C CAC FM Letter - ASTM d3161 letter - 4 -15 -
2015 .odf
Impact Resistant: N/A FL7006 R9 C CAC FM Letter - ASTM d3462 letter - 5 6
15.pdfDesignPressure: N/A
Other: FL7006 R9 C CAC FM Letter - ASTM E 108 letter - 5 3
15 .pdf
Quality Assurance Contract Expiration Date
12/31/2020
Installation Instructions
FL7006 R9 II IKO-133-02-01 Letter - Installation
Instructions for FBC FL7006.odf
FL7006 R9 II Roofing- Products- Leadino- Edge- Plus-
Aoolication-EN(1).odf
Verified By: Duc T Nguyen PE 65034
Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
Marathon 25 AR, CRC Superglass 3 tab fiberglass asphalt shingle manufactured at IKO's
x?param=wGEVXQwtDgse7mYBd2b3K6mXtoZLhN VX122N pl70J 1 E%3d 2/3
rTy
2/10/2017 Florida Building Code Online
M25AR Brampton, Ontario, Hawkesbury Ont., Toronto, Ont.;
Sylacauga, AL and Kanakakee, IL plants
Limits of Use Certification Agency Certificate
Approved for use in HVHZ: Yes FL7006 R9 C CAC FM Letter - ASTM d3161 letter - 4 -15 -
2015 .DdfApprovedforuseoutsideHVHZ: Yes
Impact Resistant: N/A FL7006 R9 C CAC FM Letter - ASTM d3462 letter - 5 6
15.0DesignPressure: N/A
Other: FL7006 R9 C CAC FM Letter - ASTM E 108 letter - 5 3
15 .pdf
Quality Assurance Contract Expiration Date
12/20/2020
Installation Instructions
FL7006 R9 II IKO-133-02-01 Letter - Installation
Instructions for FBC FL7006.1)df
Verified By: Duc T Nguyen 65034
Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
back Next
Contact Us :: 2601 Blair Stone Road, Tallahassee FL 32399 Phone: 850-487-1824
The State of Florida is an AA/EEO employer. Copyright 2007-2013 State of Florida.:: Privacy Statement :: Accessibility Statement :: Refund Statement
Under Florida law, email addresses are public records. If you do not want your e-mail address released in response to a public -records request, do not send electronic
mail to this entity. Instead, contact the office by phone or by traditional mail. If you have any questions, please contact 850.487..1395. *Pursuant to Section.
455.275(1), Florida Statutes, effective October 1, 2012, licenseeslicensed under Chapter 455, F.S. must provide the Department with an email address if they.have
one. The emails provided may be used for official communication with the licensee. However email addresses are public record. If you do not wish to supply a
personal address, please provide the Department with an email address which can be made available to the public. To determine if you are a licensee under Chapter
455, F.S., please click here
Product Approval Accepts:
im Ed .,
Credit
Safe
securit<<n1,;r Ics•
http://www.floridabui ldi ng.org/pr/pr_app_otl.aspx?param=wGEVXQwtDgse7mYBd2b3K6mXtoZLhN VXI22N pl7OJ 1 E%3d 3/3
TECH NO LOG UES
March 30, 2015
KOIndustries, Ltd
120Hay Rd.
Wilmington, DE10OOQ
Re: FBCFL700O
Sir(s).
PRI Construction Materials Technologies has completed atechnical review and attached sealed shingle
instructions in compliance the 2014 Iorida Building'Code.
This review was completed based on the receipt of following evidence from UKD Industries, Ltd:
1)
2) V<OLaminated Shingles Application Instructions
02-rovO7/13-Florida
3)]KO Hip nd Ridge,12 Application Instructions
E `'`Rid` —
IKO Leading Edge Plus Shingle — Instructions `
EN-3LEP-Tri-2012-06—reformatted 2013-03)
5) ASTM D3161 Test Report (FM Approvals Project No. 3040947)
The attached instructions should beused inconjunction with the published manufacturer's application
instructions and applicable code. In the event the instructions conflict, these instructions shall govern.
Statement of Independence: PRI Construction Materials Technologies and/or Duc T. Nguyen, FL P.E. do not
have nor plan to acquire a financial interest in any company manufacturing or distributing products for which
the test reports are issued.
X1
Signed: Signed:
P.E. Number: 65034
Date: April 30.2015 Date: April 3U.2015
Attachments: A)|KOShingle Application Instructions '3 -Tub
B)|KOLaminated Shingles Application Instructions
C)|KOHip and Ridge 12Application Instructions
D)|KOLeading Edge Plus Application Instructions
PRI Construction Materials Technologies, LLC. m1uBadger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: wobSite: hftp:mwww.pricmmo
IKO
Installation Instructions for
Asphalt Shingles
Page 2 of 5
IKO Shingle Application Instructions — 3 -Tab Shingles
ASTM D3161; Class F — IKO Marathon 25 AR and CRC Superglass M25AR)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
ROOF DECK: Solidly sheathed and fastened deck conforming to 2014 FBC.
UNDERLAYMENT: Applied in accordance with building code requirements. For areas where the roof slope is
less than 4" per foot down to 2" per foot, use 2 layers of underlayment conforming to building code
requirements, the first sheet overlapping the eave protection by 19", followed by full 36" widths overlapping
each preceding course by 1.9" or other Approved underlayments in accordance with the qualified application
instructions. For areas ';where the roof slope is 4" per foot or greater, cover the deck with one ply of
underlayment laid parallel to the eaves, with 2" horizontal laps and 4" end laps. Apply metal drip edges on top
of any underlay along rake edges and directly to the deck along eaves in accordance with building code
requirements.
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8" diameter heads, long
enough to penetrate through plywood or 3/4" into boards. Use 4 nails per shingle placed 6-1/8" above the butt
edge, approx. 1" and 13";from each end and 1/2" above each cutout. Drive nails straight so that nail head is
flush with, but not cutting into shingle surface.
NAILING ON STEEP SLOPES: For steep slopes of 21" per foot (60°) or more, use 6 nails per shingle placed
as shown below. Ensure that no nail is within 2" of a joint/cutout of the underlying shingle. Seal down each
shingle at time of applica#ion with three 1 " diameter (approx. size and thickness of a quarter) spots of asphalt
plastic cement placed under the shingle 2above the bottom edge and equally spaced along the shingle.
Apply plastic cement in moderation since excessive amounts may cause blistering. CAUTION: Shingles
should seal to the underlying course when .the factory applied asphalt sealant is sufficiently warmed by the
heat of direct sunlight.
EXPOSURE: Installed shingles shall have a maximum average exposure of 5-5/8".
1
T t
6-118" 112"
NAILS"
STEEP SLOPES
1-112" 1-12"
SEALING STRIP a e o 0 o e
6-118"
NAILS
DO NOT NAIL INTO OR ABOVE THE SEALING STRIP
chnologies, LLC. 6412 Badger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: materialstesting@pricmt.com WebSite: http://www.pricmt.com
IKO '
Installation Instructions for
Asphalt Shingles
Page 3 of 5
IK® Laminated Shingles Application Instructions
ASTM D3161, Class`F - Cambridge, Cambridge HD, and CRC Biltmore AR)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CON.JUCTION WITH IKO'S PUBLISHED
APPLICATIONINSTRUCTIONS AND THE APPLICABLE CODE. IN THE' EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
ROOF DECK: Solidly sheathed and fastened deck conforming to 2014 FBC
U N DERLAYM ENT: Applied in accordance with building code requirements. For areas where the roof slope is
less than 4" per. foot-down'to 2" per foot, use 2 layers of underlayment conforming to building code
requirements,, the first sheet overlapping the eave protection by 19", followed by full 36" widths overlapping
each preceding course by 19" or other Approved underlayments in accordance with the qualified application
instructions. For areas where the roof slope is 4" per foot or greater, cover the deck with one ply of
underlayment laid parallel to the eaves, with 2" horizontal laps and 4" end laps. Apply metal drip edges on top
of any underlay along rake edges and directly to the deck along eaves in accordance with building code
requirements.
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8" diameter heads, long
enough to penetrate through plywood or 3/4" into boards. Use 4 nails per shingle placed in the nail line 7-3/8"
below the top edge, approx. 1" and 13" in from each end. Drive nails straight so that nail head is flush with,
but not cutting into shingle surface.
NAILING ON STEEP SLOPES: For steep slopes of 21" per foot (60°) or more, use 6 nails per shingle placed
as shown below. Ensure that no nail is within 2" of a joint/cutout of the underlying. shingle'. Seal down each
shingle at time of application with three 1" diameter (approx.*size and thickness of a_.quarter) spots of asphalt
plastic cement placed under the shingle, 2" above the bottom edge and equally spaced.along'the shingle.
Apply plastic cement in moderation since excessive amounts may cause blistering. CAUTION: Shingles
should seal to the underlying course when the factory applied asphalt sealant is sufficiently warmed' by the
heat of direct sunlight.
EXPOSURE: Installed shingles shall have a maximum average exposure of 5-7/8".
6 3/8"I
NAIL LINE
NAILING - STEEP SLOPES APPLICATION
Use six nails as shown.
CEMENT
PROPER APPLICATION REQUIRES THAT THE NAILS PENETRATE BOTH THE OVERLAY AND UNDERLAY PORTIONS OFTHE SHINGLE
PRI Construction Materials Technologies, LLC. 6412 Badger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: materialstesting@pricmt.com WebSite: hUp://www.pricmt.com
IKO
Installation Instructions for
Asphalt Shingles
Page 4 of 5
IK® Hip and Ridge ,12 Application Instructions
ASTM D3161, Class F — IKO Hip and Ridge 12)
NOTE: THESE I
INSTRUCTIONS SHALL < BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
Cut hip and ridge shingles into thirds, using the perforation marks as a cutting guide. These shingles are
designed for a 5 1/8 (130. mm) exposure. (For a neater appearance, the top of each side of each piece has
been factory trimmed on a 1" (25 mm) taper (see drawing). Bend each piece over the hip or ridge, and nail 5
5/8" (143 mm) above the, butt edge 1 (25 mm) in from each edge, exposing each piece 5 1/8" (130 mm).
Apply hip pieces starting at;the lower end of the hip, working up toward the ridge. On hip roofs, apply ridge
pieces starting at each end, meeting in the middle. On gable roofs, apply ridge pieces starting at the end
opposite to the prevailing,wind direction and continue to the other end. Note: To obtain a three-dimensional
effect, (which is recommended, but not required), apply hip and ridge shingles double thickness by stacking 2
pieces on top of one another, the lower piece extending about 3/4" (19 mm) further than the top piece (see
diagram). The final shingle should be set in cement, and the exposed nail heads of the final shingle should be
covered with cement. Priorao application in, cold weather, storing the shingles in a heated area will allow for
easier bending.
NOTE: SHINGLES MUST BE APPLIED PROPERLY. THEYARE DESIGNED FOR USE AS HIP AND RIDGE
SHINGLES ONLY, AND'$HOULD NOT BE USED FOR ANY OTHER APPLICATIONS. WE ASSUME NO
RESPONSIBILITY FOR LEAKS OR DEFECTS RESULTING FROM POOR APPLICATION OR FAILURE TO
PROPERLY PREPARE THE SURFACE TO BE ROOFED OVER, OR FAILURE TO PROVIDE PROPER
VENTILATION IN ACCORDANCE WITH MINIMUM PROPERTY STANDARDS REQUIREMENTS. REVIEW
ALL APPLICABLE BUILDING CODES, MINIMUM PROPERTY STANDARDS, AND REQUIREMENTS PRIOR
TO APPLYING THESE SHINGLES USING THESE APPLICATION INSTRUCTIONS.
25 mm)
TAPER CUT
Technologies, LLC. 6412,Badger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: materialstesting@pricmt.com Website: http://www.pricmt.com
IKO
Installation Instructions for
Asphalt Shingles
Page 5 of 5
IK® Leading Edge Plus Application Instructions
ASTM D3161, Class F — IKO Leading Edge Plus)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
AP.PLICATIOWINSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
1. Apply any underlayment, eave protection, valley flashings, or drip edges to roof deck as required
2. Each 39 3/8" x 13 1/4" (1000 mm x 336 mm) IKO Leading Edge Plus strip is perforated lengthwise for
separation into two (2) shingles. Take one IKO Leading Edge Plus strip and fold flat at perforation to
separate.
3. Take one of the separated shingles 39 3/8" x 6 5/8" (1000 mm x 168 mm) and remove approximately
20"(500 mm). Install this shingle on the lower left corner of the roof deck, granule side up, with the
factory installed sealant adjacent to the eaves. The shingle should overhang the rake edge and,eaves
by a nominal 1/4" (6 mm) minimum. Fasten the shingle to the roof deck with nails located 3" to 4" (75
mm to 100 mm) from the eave edge and 1" (25 mm) in from each end.
4. Take the leftover 20" (500 mm) piece shingle. Rotate the piece and align it vertically up the rake edge
with the factory installed sealant adjacent to the outer edge of the roof. The shingle should overhang
the rake edge by a nominal 1/4" (6 mm) minimum. Fasten the shingle to the roof deck with fasteners
located 3" to 4" (75 mm to 100 mm) from the rake edge and 1" (25 mm) in from each end.
5. Repeat Steps 3 — 4 for the right lower corner of the roof deck.
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least
3/8" (9 mm) diameter heads, long enough to penetrate through plywood or 3/4"(20
mm) into boards. Use 4 nails per shingle placed 3" to 4" (75 mm to 100 mm) from
the eave edge and approximately 1" and 13" (25 mm and 330 mm) in from each end.
6. Apply full-length IKO Leading Edge Plus shingles to the remaining eave edges of the roof deck. Install
the shingles granule side up with the factory applied sealant adjacent to the eaves. The shingles
should overhang the rake edge and eaves by a nominal 1/4" (6 mm) minimum. Fasten the shingles to
the roof deck with nails located 3" to 4" (75 mm to 100 mm) from the eave edge, 4 nails per shingle.
7. Apply roof shingles as per the instructions printed on each product's package. Make certain the first
course of field shingle lies flush with the edges of the fastened IKO Leading Edge Plus. In this way,
the sealant on; the IKO Leading Edge Plus shingles will adhere to the first -course field shingles and
help keep them from lifting in high winds.
PRI Construction Materials Technologies, LLC. 6412 Badger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: materialstesting@pricmt.com Website: http://www.pricmt.com
2/10/2017 Florida Building Code Online
XIMiMlliy
i BCIS Home Log In User Registration i Hot Topics ( Submit Surcharge Stats & Facts
a
d^rb
Product ApprovalS&I USER: Public User
Product Approval Menu > Product or Application Search > Application List > Application Detail
FL # FL15216-R2
Application Type Revision
Code Version 2014
Application Status Approved
Comments
Archived
P4"Mx
Publications i FBC Staff BCIS Site Map ( Links I Search i
Product Manufacturer InterWrap, Inc.
Address/Phone/Email 32923 Mission Way
Mission, NON -US 00000
551) 574-2939
mtupas@interwrap.com
Authorized Signature Eduardo Lozano
elozano@interwrap.com
Technical Representative Eduardo Lozano
Address/Phone/Email 32923 Mission Way
Mission, NON -US 00000
778) 945-2891
elozano@interwrap.com
Quality Assurance Representative
Address/Phone/Email
Category Roofing
Subcategory Underlayments
Compliance Method Evaluation Report from a Florida Registered Architect or a Licensed
Florida Professional Engineer
i Evaluation Report- Hardcopy Received
Florida Engineer or Architect Name who developed Robert Nieminen
the Evaluation Report
Florida License PE -59166
Quality Assurance Entity Intertek Testing Services NA, Inc.
Quality Assurance Contract Expiration Date 11/17/2017
Validated By John W. Knezevich, PE
i Validation Checklist - Hardcopy Received
Certificate of Independence FL15216 R2 COI 2015 01 COI Nieminen.pdf
Referenced Standard and Year (of Standard)
Equivalence of Product Standards
Certified By
Sections from the Code
1507.2.3
1507.5.3
1507.8.3
1507.9.3
http://Www.floridabuildi ng.orglprlpr_app_dtl.aspx?param=wGEVXQwtDgv3yVVKJZl QRAdhyl2u8kQGQyljaH hVeiOpVSvxwSdCoQ%3d%3d 1/2
2/10/2017
Product Approval Method
Date Submitted
Date Validated
Date Pending FBC Approval
Date Approved
Summary of Products
Florida Building Code Online
1507.9.5
T1507.8
Method 2 Option B
04/28/2015
04/29/2015
05/04/2015
06/23/2015
h
FL # Model, Number or Name Description
15216.1 RhinoRoof Underlayments Synthetic roof underlayments
Limits of Use
Approved for use in HVHZ: No
Installation Instructions
FL15216 R2 II 2015 04 FINAL ER INTERWRAP RHINOROOF FL15216-
R2.pdf
Verified By: Robert Nieminen PE -59166
Created by Independent Third Party: Yes
Approved for use outside HVHZ: Yes
Impact Resistant: N/A
Design Pressure:' N/A
Other: See ER Section 5 for Limits of Use. Evaluation Reports
FL15216 R2 AE 2015 04 FINAL ER INTERWRAP RHINOROOF FL15216-
R2.pdf
Created by Independent Third Party: Yes
Back Next
Contact Us :: 2601 Blair Stone Road Tallahassee FL 32399 Phone: 850-487-1824
The State of Florida is an AA/EEO employer. Coovriaht 2007-2013 State of Florida :: Privacy Statement :: Accessibility Statement :: Refund Statement
Under Florida law, email addresses are public records. If you do not want your e-mail address released in response to a public -records request, do not send electronic
mail to this entity. Instead, contact the office by phone or by traditional mail. If you have any questions, please contact 850.487.1395. *Pursuant to Section
455.275(1), Florida Statutes, effective October 1, 2012, licensees licensed under Chapter 455, F.S. must provide the Department with an email address if they have
one. The emails provided may be used for official communication with the licensee. However email addresses are public record. -If you do not wish to supply a
personal address, please provide the Department with an email address which can be made available to the public. To determine if you are a licensee under Chapter
455, F.S., please click here .
Product Approva I Accepts:
d:hecY.
Credit Card
Safe
ix?param=wGEVXQwtDgv3yVVKJZ 1 QRAdhyl2u8kQGQyljaH hVei OpVSvxwSdCoQ%3d%3d 2/2
C)c
EVALUATION REPORT
Interwrap, Inc.
32923 Mission Way
Mission, BC V2V-6E4
Canada
EXTERIOR RESEARCH & DESIGN, LLC.
Certificate of Authorization #9503
353 CHRISTIAN STREET, UNIT #13
OXFORD, CT 06478
PHONE: (203) 262-9245
FAX: (203) 262-9243
Evaluation Report 140510.02.12-112
FL15216-R2
Date of Issuance: 02/17/2012
Revision 2: 04/27/2015
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code
sections noted herein.
DESCRIPTION: RhinoRoof Underlayments
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product
changes or the referenced Quality Assurance documentation changes. Trinity I ERD requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity IERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire. Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 3.
Prepared by:
Robert J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCA ANE1983
The facsimile seal appearing was authorized by Robert Nieminen,
P.E. on 04/27/2015. This does not serve as an electronically signed
document. Signed, sealed hardcopies have been transmitted to the
Product Approval Administrator and to the named client
CERTIFICATION OF INDEPENDENCE:
1. Trinity IERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity I ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
C)o
l TRINITY ERD
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Underlayment
Compliance Statement: RhinoRoof Underlayments, as produced by Interwrap, Inc., has demonstrated compliance with the
intent of following sections of the Florida Building Code through testing in accordance with applicable sections of the following
Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein.
2. STANDARDS:
Section Properties Standard Year
1507.2.3, 1507.5.3, T1507.8, Unrolling, Breaking Strength, Pliability, Loss ASTM D226 2006
1507.8.3, 1507.9.3, 1507.9.5 on Heating
1507.2.3, 1507.5.3, 1507.8.3, Unrolling, Tear Strength, Pliability, Loss on ASTM D4869 2005
1507.9.3 Heating, Liquid Water Transmission,
Breaking Strength, Dimensional Stability
3. REFERENCES:
Entity Examination Reference Date
ITS (TST1509) Physical Properties 10053939SCOQ-006 10/27/2011
ITS (TST1509) Physical Properties 100539395COQ-002 10/27/2011
ITS (TST1509) Physical Properties 100539395COQ-006 03/14/2014
ITS (QUA1673) Quality Control Inspection Report 11/17/2014
4. PRODUCT DESCRIPTION:
4.1 RhinoRoof U20 is a multilayered polymer woven coated synthetic roof underlayment intended as an alternate to ASTM
D226, Type I or Type II felt or D4869 Type II felt. RhinoRoof Underlayment is available in 42 -inch wide rolls, and can be
produced in various other sizes.
5. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the Designer of
Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or
design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory or test
report from accredited testing agency for fire ratings of this product.
5.4 RhinoRoof Underlayments may be used with any prepared roof cover where the product is specifically referenced
within FBC approval documents. If not listed, a request may be made to the AHJ for approval based on this evaluation
combined with supporting data for the prepared roof covering.
5.5 Allowable roof covers applied atop RhinoRoof Underlayments are follows:
6.
5.6 Exposure Limitations:
5.6.1 RhinoRoof Underlayment shall not be left exposed for longer than 30 -days after installation.
INSTALLATION:
6.1 RhinoRoof Underlayments shall be installed in accordance with Interwrap, Inc. published installation instructions
subject to the Limitations set forth in Section 5 herein and the specifics noted below.
Install RhinoRoof,Underlayments in compliance with manufacturer's published installation instructions and the
requirements for ASTM D226, Type I or II or D4869, Type II underlayments in FBC Sections 1507 for the type of
prepared roof covering to be installed.
Irch and Design, LLC.
luthorization #9503
Evaluation Report 140510.02.12-112
FL15216-R2
Revision 2: 04/27/2015
Page 2 of 3
i TABLE 1 ROOF COVER OPTIONS
Asphalt Wood Shakes Slate or
Underlayment
Shingles
Nail -On Tile Foam -On Tile Metal
Shingles Simulated Slate
RhinoRoof U20 Yes No No Yes Yes No
6.
5.6 Exposure Limitations:
5.6.1 RhinoRoof Underlayment shall not be left exposed for longer than 30 -days after installation.
INSTALLATION:
6.1 RhinoRoof Underlayments shall be installed in accordance with Interwrap, Inc. published installation instructions
subject to the Limitations set forth in Section 5 herein and the specifics noted below.
Install RhinoRoof,Underlayments in compliance with manufacturer's published installation instructions and the
requirements for ASTM D226, Type I or II or D4869, Type II underlayments in FBC Sections 1507 for the type of
prepared roof covering to be installed.
Irch and Design, LLC.
luthorization #9503
Evaluation Report 140510.02.12-112
FL15216-R2
Revision 2: 04/27/2015
Page 2 of 3
8.
F)o
t TRINITY ERD
6.3 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove
any dust and debris prior to application.
6.4 RhinoRoof U20:
6.4.1 Fasteners:
For exposure < 24 hours, corrosion resistant fasteners may be 1 -inch roofing nails with a 3/8 -inch diameter head, or
those noted in 6.4.2. The use of staples is prohibited.
For exposure > 24 hours up to maximum 30 days, corrosion resistant fasteners shall be minimum 1 -inch diameter
plastic or metal cap nails or FBC HVHZ nails & 1-5/8" diameter tin caps (with the rough edge facing up). The use of
staples is prohibited.
6.4.2 Single Layer; Roof Slope > 4:12:
End (vertical) laps shall be minimum 6 -inches and side (horizontal) laps shall be minimum 4 -inches. Refer to Interwrap,
Inc. recommendations for alternate lap configurations and/or the use of sealant under certain conditions.
For exposure < 24 hours, use of every -other fastening location printed on the surface is acceptable. For exposure > 24
hours up to maximum 30 -days, use of every fastening location printed on the surface is required.
When batten systems are to be installed atop the underlayment, the underlayment need only be preliminarily attached
pending attachment of the battens on the same day. Battens shall not be positioned over cap nails. If this occurs,
remove the cap nail and patch the hole in accordance with Interwrap published instructions.
6.4.3 Double Laver; 2:12 < Roof Slope < 4:12:
End (vertical) laps shall be minimum 12 -inches and side (horizontal) laps shall be minimum half -sheet -width plus 1 -inch.
Double layer application; begin by fastening a half -width plus 1 -inch starter strip along the eaves. Place a full -width
sheet over the starter, completely overlapping the starter course. Continue as noted in 6.5, but maintaining minimum
half -width plus 1 -inch side (horizontal) laps, resulting in a double -layer application.
BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product.
MANUFACTURING PLANTS:
Contact the manufacturer or the named QA entity for information on plants covered under Rule 61G20-3 QA requirements.
QUALITY ASSURANCE ENTITY:
Intertek Testing Services NA Inc.-ETL/Warnock Hersey — QUA1673; (604) 520-3321
END OF EVALUATION REPORT -
Exterior Research and Design, LLC. Evaluation Report 140510.02.12-112
Certificate of Authorization 119503 F1.15216-112
Revision 2: 04/27/2015
Page 3 of 3
City of Sanford Building Division
Residential Re -Roof Inspection Policy & Procedures
PERMITTING REQUIREMENTS — NO PLAN REVIEW REQUIRED
THIS DOCUMENT (SIGNED) ALONG WITH AN ACCURATE AND COMPLETED RESIDENTIAL RE ROOF SCOPE OF WORK ARE
REQUIRED TO BE SUBMITTED AS PART OF YOUR PERMIT APPLICATION.
THE SCOPE OF WORK MUST INCLUDE ALL APPLICABLE FLORIDA PRODUCT APPROVAL NUMBERS FOR ALL ROOF
COMPONENTS THAT WILL BE INSTALLED ON THE PROJECT.
A PERMIT WILL NOT BE ISSUED WITHOUT THESE DOCUMENTS. COPIES WILL BE MADE TO POST ON THE JOB SITE.
PROJECTS LOCATED IN THE SANFORD HISTORIC DISTRICT WILL REQUIRE PLAN REVIEW AND APPROVAL BY THE
SANFORD HISTORIC PRESERVATION BOARD
INSPECTION POLICY & PROCEDURES
A FINAL ROOF INSPECTION IS THE ONLY INSPECTION REQUIRED FOR RESIDENTIAL (SINGLE FAMILY, TOWNHOUSE,
s MOBILE HOME, APARTMENT AND/OR CONDOMINIUM) RE -ROOF PERMITS.
THE FOLLOWING IS REQUIRED TO BE PROVIDE ON THE JOB SITE:
PERMIT CARD, POSTED IN A CONSPICUOUS AND WEATHERPROOF LOCATION
COMPLETED RESIDENTIAL RE -ROOF SCOPE OF WORK
COMPLETED AND NOTARIZED INSPECTION AFFIDAVIT
ALL FLORIDA PRODUCT APPROVAL AND CORRESPONDING INSTALLATION INSTRUCTIONS
PRODUCT APPROVAL SHALL MATCH WHAT IS ON THE SCOPE OF WORK)
DIGITAL PHOTOGRAPHS (MUST INCLUDE THE PERMIT NUMBER OR ADDRESS IN EACH PICTURE)
o EACH PLANE OF THE ROOF, SHOWING THE UNDERLAYMENT INSTALLED
o ROOF DECK NAILING PATTERN & SPACING (INCLUDING A•MEASURING DEVICE OR RULER)
o ROOF DECK NAILS USED (INCLUDING A MEASURING DEVICE OR RULER SHOWING SIZE OF NAILS)
o UNDERLAYMENT PATTERN & SPACING (INCLUDING A MEASURING DEVICE OR RULER)
o DRIP EDGE & VALLEY ATTACHMENT (INCLUDING A MEASURING DEVICE OR RULER)
o SHINGLES INSTALLED, NAIL PATTERN AND LOCATION OF NAILS
SKYLIGHTS (IF APPLICABLE)
o DIGITAL PHOTOGRAPHS SHOWING ALL INSTALLATION COMPONENTS, PER FL PRODUCT APPROVAL
o DIGITAL PHOTOGRAPHS SHOWING ALL REQUIRED FLASHING, PER FL PRODUCT APPROVAL
FAILURE TO FOLLOW THESE SPECIFIC GUIDELINES WILL RESULT IN AN AFFIDAVIT PROVIDED BY A FLORIDA DESIGN
PROFESSIONAL (ARCHITECT OR ENGINEER), CERTIFYING FBC CODE COMPLIANCE BY PERSONAL INSPECTION.
CONTRACTOR (OR OWNER/BUILDER)SIGNATURE: DATE:
JOB ADDRESS:
PEPmT #
City of Sanford Building Division
Residential Re -Roof Scope of Work
STRUCTURE TYPE:® SINGLE FAMILY RESIDENCE/TOWNHOUSE 0 MOBILE HOME O APARTMENT/CONDOMINIUM
RE -ROOF TYPE:. , REPLACEMENT (TEAR OFF EXISTING ROOF AND REPLACE WITH NEW COMPONENTS)
Q RE-COVER (NEW ROOF INSTALLED OVER EXISTING ROOF)
DECK TYPE (PLEASE SPECIFY):
PLEASE NOTE: ONLY100 SQUARE FEET OF THEEXISTINGDECKIS PERMITTED TO BEREPLACED**
ROOF VENTILATION: 61OFF-RIDGE Q RIDGE OSOFFIT OPOWERED VENT OTURBINES
SKYLIGHTS: O YES 6,NO IF YES, PLEASE PROVIDE FLORIDA PRODUCT APPROVAL#:
MAIN ROOF AREA
ROOF SLOPE: 0 LESS THAN 2:12 02:12-4:12 4114:12 OR GREATER
TYPE OF ROOF MANUFACTURER FLORIDA PRODUCT APPROVAL
SHINGLE T It l% Fu '10N - '91
O METAL FL#
0 MODIFIED BITUMEN FL#
O TORCH DOWN FL#
OINSULATED FL#
OTILE FL#
0 OTHER: FL#
ROOF EXTENSIONS (PORCHES, PATIOS. ETC.) **IFAPPLICABLE**
ROOF SLOPE: 0 LESS THAN 2:12 02:12-4:12 04:12 OR GREATER
TYPE OF ROOF MANUFACTURER FLORIDA PRODUCT APPROVAL
0 SHINGLE FL#
O METAL FL#
0 MODIFIED BITUMEN FI #
OTORCH DOWN FL#
OINSULATED FL#
OTILE FL#
Q OTHER: FL#
07/07 NOTICE OF COMMENCEMENT GRANT 11ALOY, SENINOLE COUNTY
ft j,
1
joie LU,I r CLERK( OF CIRCUIT COURT & CONPTROLLER
State of Florida 11G(+ -.361l I's 825 C 11='s= tIolin9BK
ofuolusiaySG0A t'V) l (. J BOY,, CLE'RK'S v 201701565852os% RECORDED 2/14/21i17 1i9.'21,.).2 +=11'1PermitNo011QVkOk", Fl 329752-G668 RI:C.ORGING < FEES 1%10.00FEES
Tax Parcel Number RECORDED BY ilil+=vor e
The UNDERSIGNED hereby gives notice that improvement will be made to certain
real property, and in accordance with Chapter 713, Florida Statutes, the following
information is provided in this Notice of Commencement
1. Description of Property, (Legal descrlptlorypf the prope and street address If available.)
2. General description of improvement:
Roof Replacement I
3. Owner information:
a. Name and address AK /
b. Interest in property , 1)/,I 1ov
c. Name and address of fee simple titleholder (if other than owner)
sv/
p,
4. Contractor:
Name and address
Collis Roofing, Inc.
P.O. Box 520668, Longwood, FL. 32752
a. Phone number 321-441-2300
Fax number
321-441-2313
5. Surety: Name and address
a. Phone number( )
Fax number ( )
b. Amount of bond $ .00
6. Lender: Name and address
a. Phone number(
Fax number (
7. Persons within the State of Florida designated by Owner upon whom notices or other
documents may be served as provided by Section 713.13(1)(a)7., Florida Statutes:
a. Name and address
b. Phone number(
Fax number (
1. -1. P1GC1I^C I ICC ^.. V
8. in addition to himself, Owner designates of
to receive a copy of the Lienor's Notice as provided in Section 713.13(1)(b), Florida Statutes
a. Phone number( )
b. Fax number( )
9. Expiration date of Notice of Commencement (the expiration date is 1 year from the date of recording
unless a different date is specified)
WARNING TO OWNER: ANY PAYMENTS MADE BY THE OWNER AFTER THE EXPIRATION OF THE NOTICE OF COMMENCEMENT
ARE CONSIDERED IMPROPER PAYMENTS UNDER CHAPTER 713, PART I, SECTION 713.13, FLORIDA STATU S`PY -GRANT MAt.OY ,. • .,,
RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEME Ir} _
RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN F I tit CIRCUIT COURT ^ YT`'" `v?
CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE COMMENCING WORK OR RECORDING YOUR NOVaiti' ROLL
SEMINOLE C N 1 FL0 ACOMMENCEM
i1S,,la /%U CAZ*n.,e of Oer Print Name of Owner UEPUTY CLERKto
State of Florida Cg(n typf '/"7 it a •c FEB 14 2017
Affirmed and subsf/nfb/e0 b/! rree p,{e this day of 20 by `
d/
l
9 / '9 T Ll (00 9 !— (n -3 Z —V (type of ID) as identification.
who is pergop Ily jcno n t 'me r uc d
nature of Nota •
PiiIm
Type or Stamp Name of Notary
County Permit Center Fax # 386-740-5238NotarialSeal
My Comm. Expires Ocl 29, 2020
City of Sanford
Building and Fire Prevention
i nJ
W
yl
RESIDENTIAL RE—ROOF INSPECTION AFFIDAVIT
NAILING, SHEATHING, DRY—IN, FLASHING, AND. ALL FINAL ROOF COVERINGS
PERMIT #,`: LlV ADDRESS: N05 Y 1 OY I
f
flI100 "%"" • _ L& AS A(N) GENERAL, BUILDING, RESIDENTIAL, OR
ROOFING CONTRACTOR, ENGINEER, ARCHITECT, OF F.S. CHAPTER 468 BUILDING INSPECTOR, I HEREBY AFFIRM, THAT ALL OF THE
FOREGOING INFORMATION IS TRUE AND ACCURATE AND THAT ALL ROOFING COMPONENTS LISTED ON THE SCOPE OF WORK AT THE
ABOVE REFERENCED ADDRESS HAVE BEEN INSTALLED IN ACCORDANCE WITH THEIR PRODUCT APPROVALS AND ALL APPLICABLE CODE
REQUIREMENTS — SPECIFICALLY FLORIDA BUILDING CODE, EXISTING BUILDING. IN ADDITION I CERTIFY THE INSTALLATION MEETS ALL
REQUIREMENTS FOR SECONDARY WATER BARRIER AND NAILING OF THE ROOF DECK, IN ACCORDANCE WITH THE HURRICANE RETROFIT
MANUAL REQUIREMENTS (BASED ON F.S..CHAPTER 553.844).
LICENSE
COMPANY/CONTRACTOR:__ W I S K,6U I L
CONTRACTOR SIGNATURE:
MUST BE SIGNED BY LICEN OR OWNER/BUILDER)
A FINAL ROOF INSPECTION IS REQUIRED:
DATE:
THIS SIGNED AND NOTARIZED AFFIDAVIT MUST BE PROVIDED AT THE JOB SITE AT THE TIME OF THE FINAL ROOF INSPECTION,
ALONG WITH DIGITAL PHOTOGRAPHS OF EACH PLANE OF THE ROOT. SHOWING IN DETAIL ALL COMPONENTS (DECKING,
UNDERLAYMENT, FLASHING, DRIP EDGE ATTACHMENT) WITH THE PERMIT NUMBER OR ADDRESS CLEARLY MARKED ON THE DECK
FOR EACH INSPECTION. THE PHOTOGRAPHS MUST INCLUDE A RULER OR MEASURING DEVICE TO CONFIRM ALL NAIL SPACING AND
OVERLAPS, INCLUDING DRIP EDGE AND VALLEY FLASHING. PLEASE REFER TO THE RE–ROOF POLICY AND INSPECTION PROCEDURE
PAPERWORK FOR FURTHER EXPLANATION OF ALL REQUIREMENTS.
FAILURE TO FOLLOW ALL REQUIREMENTS WILL RESULT IN A FAILED INSPECTION, A RE -INSPECTION FEE AS
WELL AS REQUIRING A DESIGN PROFESSIONAL (ARCHITECT OR ENGINEER) TO CERTIFY, BASED ON PERSONAL
INSPECTION, THE INSTALLATION OF ALL ROOFING COMPONENTS.
STATE OF FLORIDA COUNTY OF
t
Sworn to and Subscribed before me this day of / 20 by:
A
Who is ersonally Known to me o has Produced (type of
State of Florida
cc ----'
Print/Type/Stamp Name
of.Notary Public
as identification.
Hn, _ h'A"'
STEPHANIE J.
Notar p WII IAMSYPuStateofFloridafCommission # GG 008373norCnn,rr, Expires Oct 29,202o