HomeMy WebLinkAbout106 N Somerset Ct0 CITY OF SANFORD
BUILDING & FIRE PREVENTION
PERMIT APPLICATION
Application No:
p.o
Documented Construction Value: $
Job Address: 106 N SOMERSET CT SANFORD, FL 32773 Historic District: Yes No
Parcel ID: 07-20-31-506-0000-0350 Residential x Commercial
Type of Work: New Addition Alteration Repair Demo Change of Use Move
Description of Work: Roof Replacement
Plan Review Contact Person: Justin Shelton Title: R/R Manager
Phone: 321-441-2300 Fax:
Name Pax) &UA4--
Street:
106 N kMERSET CT
City, State Zip:
Name
321-441-2313 Email: swilliams@collisroofing.com
Property Owner Information
SANFORD, FL 32773
Phone:
Resident of property? :
Contractor Information
Collis Roofinq, Inc. Phone: 321-441-2300
Street: P n 52nFiFi13 Fax: _391-441-9313
City, State Zip: Longwood, FL. 32752 State License No.: CCC058022
Name: n/a
Street:
City, St, Zip:
Bonding Company:
n/a
Address:
Architect/Engineer Information
Phone:
Fax:
E-mail:
Mortgage Lender: n/a
Address:
WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR
PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE
RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN
FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY, BEFORE RECORDING YOUR NOTICE OF
COMMENCEMENT.
Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has
commenced prior to the issuance of a permit and that all work will be performed to meet standards of all laws regulating construction
in this jurisdiction. I understand that a separate permit must be secured for electrical work, plumbing, signs, wells, pools,
furnaces, boilers, heaters, tanks, and air conditioners, etc.
FBC 105.3 Shall be inscribed with the date of application and the code in effect as of that date: 5' Edition (2014) Florida Building Code tA
Revised: June 30, 2015 Permit Application 6q /
NOTICE: In addition to the requirements of this permit, there may be additional restrictions applicable to this property that may be
found in the public records of this county, and there may be additional permits required from other governmental entities such as water
management districts, state agencies, or federal agencies.
Acceptance of permit is verification that I will notify the owner of the property of the requirements of Florida Lien Law, FS 713.
The City of Sanford requires payment of a plan review fee at the time of permit submittal. A copy of the executed contract is required
in order to calculate a plan review charge and will be considered the estimated construction value of the job at the time of submittal.
The actual construction value will be figured based on the current [CC Valuation Table in effect at the time the permit is issued, in
accordance with local ordinance. Should calculated charges figured off the executed contract exceed the actual construction value,
credit will be applied to your permit fees when the permit is issued.
OWNER'S AFFIDAVIT: I certify that all of the foregoing information is accurate and that all work will
be done in compliance with all applicable laws regulating construction and zoning.
lee
Signature of Owned/Agent ate Signature of Co ractor/Agent Date
Print Own A s Nai Print Co ract is N e
Signatu'of N -State of
FFe&rrs
ignat o tate of Florida ate
R'I U . Y••••11STEPHANIEJ. WILLIAMS '4"aYPieSTEPHANIE JNotaryPublic - State of Florida ?: ; WILLIAMS
Commission 8 GG 008373 .`Notary Public -State of F orida
OF.f.My COmm. Expires Oct 29. 2020 F oF";' Commis ion a GG 008373Mmr
Owner/Agent is a Cont 0e>Qs81Kt@Pev to Me or
Produced ID Type of ID Produced ID ype
BELOW IS FOR OFFICE USE ONLY
Permits Required: Building Electrical Mechanical Plumbing Gas Roof
Construction Type: Occupancy Use: Flood Zone:
Total Sq Ft of Bldg: Min. Occupancy Load: # of Stories:
New Construction: Electric - # of Amps Plumbing - # of Fixtures
Fire Sprinkler Permit: Yes 'No # of Heads Fire Alarm Permit: Yes No
APPROVALS: ZONING: UTILITIES: WASTE WATER:
ENGINEERING: FIRE: BUILDING:
COMMENTS:
Revised: June 30, 2015 Permit Application
COLLIS ROOFING, INC.
P.O. Box 520668
Longwood, FL 32752-0668
Ph. (321) 441-2300
Fax (321) 441-2313
Lic. # CCCO58022 / I
Date: 11 7/12/16 Phone: 407-474-5007
Attention: Caren Bender Fax:
Job Address: 106 N Somerset Court, Sanford, FL 32773
Collis Roofing, Inc. proposes to supply the labor and materials necessary to apply your roofing as follows:
A) Remove old tile and underlayment to bare deck and dispose of properly.
B) Inspect existing decking for water damage and re -nail according to code. We will remove and replace at a rate of $65.00
per sheet of plywood or $5.00 per linear foot. (Note: This amount is not included in the total below).
C) Collis Roofing, Inc. will provide all applicable permits.
1. Supply and install code approved Rhino U20 Synthetic underlayment to deck using simplex nails.
2. Supply and install code approved 1 W' galvanized paime eave drip and secure to the roof deck with nails around all
eaves and rakes (Please specify drip edge color:
3. Secure the eave metal with mastic and then apply Tamko Starter shingles at all eaves with the seal strip at the edge of
the roof.
4. Supply and install all synthetic flashings for plumbing penetrations.
5. Supply and install color matched kitchen and bath exhaust vents.
6. Supply and install Tamko ELITE Hip and Ridge shingles as required by manufacturers warranty.
7. Supply and install code approved 4ft off ridge vents as required.
8. Supply and install code approved Midstates self -adhered underlayment and preformed 26ga galvanized metal along all
valleys per manufacturer specifications.
9. Supply and install Tamko shingles per manufacturer's specifications and all applicable building codes (Please specify
shingle color: r^i-_, .
10. Collis Roofing Inc. will supply a 5 year full coverage warranty upon completion.
A manufacturer's warranty shall be furnished if called for above. The above work shall be performed in a substantial workmanlike
manner for the sum of:
Tamko Elite 25 year 60mph (3-tab) - $7,995.00
Tamko Heritage 30 year 130mph (architectural) - $8,350.00 x
With payment to be made as follows: 100% upon completion.
Respectfully submitted: Brian C. Kuehner
Date: ( / l r0 Approved By:
Collis Roofing, Inc.
ACCORDING TO FLORIDA'S CONSTRUCTION LIEN LAW (SECTIONS 713.001-713.37, FLORIDA STATUTES),
THOSE WHO WORK ON YOUR PROPERTY OR PROVIDE MATERIALS AND ARE NOT PAID IN FULL HAVE A
RIGHT TO ENFORCE THEIR CLAIM FOR PAYMENT AGAINST YOUR PROPERTY. IF YOUR CONTRACTOR
OR A SUBCONTRACTOR FAILS TO PAY SUBCONTRACTORS, SUB -SUBCONTRACTORS, OR MATERIAL
SUPPLIERS, THE PEOPLE WHO ARE OWED MONEY MAY LOOK TO YOUR PROPERTY FOR PAYMENT, EVEN
IF YOU HAVE ALREADY PAID YOUR CONTRACTOR IN FULL. IF YOU FAIL TO PAY YOUR CONTRACTOR,
YOUR CONTRACTOR MAY ALSO HAVE A LIEN ON YOUR PROPERTY. THIS MEANS IF A LIEN IS FILED
YOUR PROPERTY COULD BE SOLD AGAINST YOUR WILL TO PAY FOR LABOR, MATERIALS, OR OTHER
SERVICES THAT YOUR CONTRACTOR OR A SUBCONTRACTOR MAY HAVE FAILED TO PAY. TO PROTECT
YOURSELF, YOU SHOULD STIPULATE IN THIS CONTRACT THAT BEFORE ANY PAYMENT IS MADE, YOUR
CONTRACTOR IS REQUIRED TO PROVIDE YOU WITH A WRITTEN RELEASE OF LIEN FROM ANY PERSON
OR COMPANY THAT HAS PROVIDED TO YOU A "NOTICE TO OWNER" FLORIDA'S CONSTRUCTION LIEN
LAW IS COMPLEX AND IT IS RECOMMENDED THAT YOU CONSULT AN ATTORNEY.
Page I of 3
Initial
LIMITED POWER OF ATTORNEY
Altamonte Springs, Casselberry, Lake Mary, Longwood, Sanford,
Seminole County, Winter Springs
Date: 08/30/16
I hereby name and appoint
an agent of:
Ray Henderson
Collis Roofing, Inc.
Name of Company)
to be my lawful attorney -in -fact to act for me to apply for, receipt for, sign for and do all things
necessary to this appointment for (check only one option):
The specific permit and application for work located at:
106 N. Somerset Court, Sanford, FL 32773
Street Address)
Expiration Date for This Limited Power of Attorney:
License Holder Name: J. Douglas Lanier
State License Number: CCC058022
Signature of License Holder:
STATE OF FLORIDA
COUNTY OF Seminole
The foregoing instrument was acknowledged before me this 30 day of August ,
200_10_, by J. Douglas Lanier who is i personally known
to me or o who has produced as
identification and who did (did not) take o /-
Notary Seal)
Signature
J
Print or type name
PHANIE J. WILLIAMS Notary Public -State of
n,,..,,, y Public -State of Florida Commission No.
Commission # GG 008373 My Commission Expires:
My Comm. Expires Oct 29, 2020
Rev. 08.12)
i l ®R
1 0
CERTIFICATE OF LIABILITY INSURANCE
DATE (MM/DD/YYYY)
12/17/2015
THIS CERTIFICATE IS ISSUED AS A MATTER OF INFORMATION ONLY AND CONFERS NO RIGHTS UPON THE CERTIFICATE HOLDER. THIS
CERTIFICATE DOES NOT AFFIRMATIVELY OR NEGATIVELY AMEND, EXTEND OR ALTER THE COVERAGE AFFORDED BY THE POLICIES
BELOW. THIS CERTIFICATE OF INSURANCE DOES NOT CONSTITUTE A CONTRACT BETWEEN THE ISSUING INSURER(S), AUTHORIZED
REPRESENTATIVE OR PRODUCER, AND THE CERTIFICATE HOLDER.
IMPORTANT: If the certificate holder is an ADDITIONAL INSURED, the policy(ies) must be endorsed. If SUBROGATION IS WAIVED, subject to
the terms and conditions of the policy, certain policies may require an endorsement. A statement on this certificate does not confer rights to the
certificate holder in lieu of such endorsement(s).
PRODUCER CONTACT
NAME:
Frank H. Furman, Inc. acoNro Ext 800-344-4838 AIC No: (954)943-5417
E-MAILADDRESS: 1314 East Atlantic Blvd.
INSURERS AFFORDING COVERAGE NAIC tfP . O. BOX 1927
INSURERA:First Specialty Insurance Corp34916PompanoBeachFL33061
INSURED INSURER B American Economy Insurance Co 19690
INSURER CAmerican Guarantee & Liability Ins 26247CollisRoofingInc
INSURERD:FRSA Self Insurer Fund N/AP. O. Box 520668
INSURER E :
1 INSURER F: Longwood FL 32752
COVERAGES CERTIFICATE NUMBER: REVISION NUMBER:
THIS IS TO CERTIFY THAT THE POLICIES OF INSURANCE LISTED BELOW HAVE BEEN ISSUED TO THE INSURED NAMED ABOVE FOR THE POLICY PERIOD
INDICATED. NOTWITHSTANDING ANY REQUIREMENT, TERM OR CONDITION OF ANY CONTRACT OR OTHER DOCUMENT WITH RESPECT TO WHICH THIS
CERTIFICATE MAY BE ISSUED OR MAY PERTAIN, THE INSURANCE AFFORDED BY THE POLICIES DESCRIBED HEREIN IS SUBJECT TO ALL THE TERMS,
EXCLUSIONS AND CONDITIONS OF SUCH POLICIES. LIMITS SHOWN MAY HAVE BEEN REDUCED BY PAID CLAIMS.
INSR
LTR TYPE OF INSURANCE
ADDL SUBR
POLICY NUMBER
POLICY EFFMM/DD/YYYY POLICY EXPMWDDNWY LIMITS
X COMMERCIAL GENERAL LIABILITY EACH OCCURRENCE 1,000,000
A CLAIMS -MADE FxI OCCUR DAMAGE TO RENTED
PREMISES Ea occurrence 50,000
X MED EXP (Any one person) EXCLUDEDContractualIncludedIRG202258011/1/2016 1/1/2017
X XCU & Broad Form PD Incl PERSONAL & ADV INJURY 1,000,000
GEN'L AGGREGATE LIMIT APPLIES PER: GENERAL AGGREGATE 2,000,000
POLICY 7X JECOT- LOC PRODUCTS - COMP/OP AGG 2,000,000
OTHER:
AUTOMOBILE LIABILITY COMBINED SINGLE LIMIT
Ea accident 1,000,000
BODILY INJURY (Per person)
B X ANY AUTO
ALL OWNED SCHEDULED
AUTOS AUTOS 02CE23335520 1/1/2016 1/1/2017 BODILY INJURY (Per accident)
PROPERTY DAMAGE
Per accident
NON -OWNED
X HIRED AUTOS Ix AUTOS
Personal Injury Protection 10,000
X UMBRELLA LIAB X OCCUR EACH OCCURRENCE 2,000,000
AGGREGATE 2,000,000C
EXCESS LIAB CLAIMS -MADE
DED I I RETENTION$ AUC914077109 1/1/2016 1/1/2017
D
WORKERS COMPENSATION
AND EMPLOYERS' LIABILITY Y / N
ANY PROPRIETOR/PARTNER/EXECUTIVE
OFFICER/MEMBER EXCLUDED?
Mandatory in NH)
NIA
870033379 1/1/2016 1/1/2017
g STATUTE I ER
E.L. EACH ACCIDENT 1,000,000
E.L. DISEASE - EA EMPLOYE 1,000,000
If yes, describe under
DESCRIPTION OF OPERATIONS below E.L. DISEASE -POLICY LIMIT 1 $ 1,000,000
DESCRIPTION OF OPERATIONS I LOCATIONS I VEHICLES (ACORD 101, Additional Remarks Schedule, may be attached if more space is required)
For Information Purposes Only"
UANUri-LA I IL)N
SHOULD ANY OF THE ABOVE DESCRIBED POLICIES BE CANCELLED BEFORE
THE EXPIRATION DATE THEREOF, NOTICE WILL BE DELIVERED IN
ACCORDANCE WITH THE POLICY PROVISIONS.
AUTHORIZED REPRESENTATIVE
Dirk De Jong/JC ^ ^"" ..-
ACORD 25 (2014/01)
INS025 ooi4mt
U 1988-2014 ACORD CORPORATION. All rights reserved.
The ACORD name and logo are registered marks of ACORD
STATE OF FLORIDA
DEPARTMENT OF BUSINESS AND PROFESSIONAL REGULATION
CONSTRUCTION INDUSTRY LICENSING BOARD
1940 NORTH MONROE STREET
TALLAHASSEE FL 32399-0783
LANI.ER, JACK DOUGLAS
COLLIS ROOFING, INC.
P O BOX 520668
LONGWOOD FL 32752-0668
Congratulations! With this license you become one of the nearly
one million Floridians licensed by the Department of Business and
Professional Regulation. Our professionals and businesses range
from architects to yacht brokers, from boxers to barbeque
restaurants, and they keep Florida's economy strong.
Every day we work to improve the way we do business in order
to serve you better. For Information about our services, please
log onto www.myfloridalicense.com. There you can find more
information about our divisions and the regulations that impact
you, subscribe to department newsletters and Team more about
the Department's initiatives.
Our mission at the Department Is License Efficiently, Regulate
Fairly. We constantly strive to serve you better so that you can
serve your customers. Thank you for doing business in Florida,
and congratulations on your new license!
RICK SCOTT, GOVERNOR KEN LAWSO.N, SECRETARY
STATE OF FLORIDA
DEPARTMENT OF BUSINESS AND PROFESSIONAL REGULATION
C.ONSTRUCTION.(NDUSTRY LICENSING. BOARD
850) 487-1395
RISTATEOFFLODA, p;• DEPARTMENT OF BUSINESS ANDtPROFESSIONALREGULATION
CCC058022IS UE® 06/.06/2016 fr t
O
R? CERTIFIEDROOM4KCONTRASLANIER
JACK DOC JGLAS " w ,
g 2 COLLISROOFINGIz
i IS'
CfiRTrF6ED u der the pT.OyG ons—of Ch A Fs s Ezpgatfon
date - AUG'31,.,2018 a 1.1606060000724 DETACH
HERE CCC058022
r_
The"
ROOFING CONTRACTOR Named
below IS CERTIFIED ``=4
M'
Under the provisions of Ch""A" r 489 FS,.-. ^ Exp
r31,, 2018_ - _ 4„ { pr ia'
LANI:ER,
JACK DOUGLA§. ONGWOOD f ~, `
a' ." „
s .
e. .+' `...
aaa
ak3
a "+a t i h, S 4 `` ',ti. a sC`s
x..r'"
a
av»•.::".-
m1e.._. °a.i&..:-,3 ..'L:.: SS. k. ., i 1., 'a X ISSUED: 06/
06/2016 DISPLAY AS REQUIRED BY LAW SEQ # L1606060000724
City of Sanford
Roof Permit Application Checklist
All permit application packages must be complete prior to acceptance. You must check each box to the
left or indicate n/a on this submittal. A complete application package shall include the following:
Building Permit Application completed, signed and notarized. Application must include correct address
and complete parcel I.D. number.
X Copy of applicable contractor's license issued by the State of Florida (if the contractor is the
applicant).
X A site specific notarized power of attorney shall be required from the licensed contractor if
he/she appoints an employee of his/her company to sign the permit application as the contractor.
I Certificate of insurance indicating worker's compensation insurance coverage and naming the City of
Sanford as certificate holder, or a copy of a worker's compensation exemption issued by the State .of
Florida (must be submitted with each application if contractor is the applicant).
Completed and signed Owner Builder Statement / Affidavit (if the owner is the applicant).
These guidelines were compiled to assist the applicant in preparing a roof permit application and may not be
complete. The applicant is required to meet all City of Sanford, state, and federal code requirements.
City of Sanford
Residential Re -Roof
Hurricane Mitigation Inspection Process
1. Roofing contractor shall be responsible for the protection of contents and structure at all
times.
2. An in -progress inspection shall be scheduled after the old roof has been removed and
the dry -in is complete. All components of the dry -in must be in place. To schedule an
inspection, call 407.688.5151.
3. For roofs using an entire peel and stick dry -in, a nailing affidavit shall be required to be
posted on jobsite at time of in -progress inspection.
4. A minimum of one hundred (100) square feet of the new roof component shall be installed
at time of inspection. Up to fifty percent (50%) of the new roof may be installed, but all
flashing and valley metal shall remain exposed for inspection.
5. The contractor shall contact the inspector the day of the scheduled inspection between
7:30 a.m. and 8:30 a.m. to coordinate the inspection time. Please call 407.688.5061 or
5063
6. At time of inspection the inspector shall, at his or her discretion, select location(s) for
inspection.
7. A representative of the contractor shall be on job site to facilitate any necessary repairs.
8. After the inspection is conducted, the contractor will make any necessary repairs and
proceed as directed by the inspector.
9. For approved inspections, the inspector shall collect the required affidavit for filing with the
permit application.
The above shall serve as the inspection process to meet requirements per Florida Statute. Any and all
suggestions to better serve the contractor needs will be considered.
2
L..ER.K.. '_!f' C:1 Rt_IS):-i COUR-1 X (C)t'IP1Fi::l._I._I::f;:
THIS INSTRUMENT PREPARED BY:
Name: Stephanie! Williams
Address: Collis Roofing, Inc.
P.O. Box 520668, Longwood FL. 32752
NOTICE OF COMMENCEMENT
State of Florida
County of Seminole
Permit Number:
C:I..FRK'8 r 2i11.6115'1.01
Parcel ID Number: 07-20-31-506-0000-0350
The undersigned hereby gives notice that improvement will be made to certain real property, and in accordance with
Chapter 713, Florida Statutes, the following information is provided in this Notice of Commencement.
DESCRIPTION OF PROPERTY: (Legal description of the property and street address if available)
LOT 35 BRYNHAVEN 1ST REPLAT PB 39 PGS 20 & 21
106 N SOMERSET CT SANFORD, FL 32773
GENERAL DESCRIPTION OF IMPROVEMENT:
Roof Replacement
OWNER INFOJRFIATION:
Name: i71.1'U
Address: 106 N SOOERSET CT SANFORD, FL 32773
Fee Simple Title Holder (if other than owner) Name:
Address:
CONTRACTOR:
Name: Collis Roofing, Inc.
Address: P.O. Box 520668, Longwood, FL. 32752
Persons within the State of Florida Designated by Owner upon whom notice or other documents may be served
as provided by Section 713.13(1)(b), Florida Statutes.
Name: n/a
Address:
In addition to himself, Owner Designates of
To receive a copy of the Lienor's Notice as Provided in
Section 713.13(1)(b), Florida Statutes.
Expiration Date of Notice of Commencement (The expiration date is 1 year from date of recording unless a
different date is specified)
WARNING TO OWNER.ANY PAYMENTS MADE BY THE OWNER AFTER THE EXPIRATION OF THE NOTICE OF
COMMENCEMENT ARE CONSIDERED IMPROPER PAYMENTS UNDER CHAPTER 713, PART I, SECTION 713.13,
FLORIDA STATUTES, AND CAN RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A
NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE JOB SITE BEFORE THE FIRST
INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY
BEFORE COMMENCING WORK OR RECORDING YOUR NOTICE OF COMMENCEMENT.
Under penalties of perjury, I declare that I have read the foregoing and that the facts stated in it are true
to the best of my knowledge and belief. v
J,kS Gp
o
Owner's Signature Owners Printed Name
J
Florida Statute 713.13(1)(g): " The owner must sign the notice of commencement and no one else may be permitted to sign in his or her stead."
ItIlL 5.
0. u O
w
y nc:(
N
State of Count of zo -
The foregoing instrument was acknowledged before me this C/- L day of % f 20 r
by 1 91 f Who is personall owrl-to me r}c
Name of person making statement Q j
OR who has produced identification type of identification produ ed: 1
J 0 W L. t
s
rn
ro4 rn Br"- ST ANC
ix_
yiEPM EJ. WILLIAMS
aotary p b . - u - State of Florida f, /Nory Signature ' L>
o.,: Commission u GG 008373
p ° My Comm, Expires Oct 29, 2020
8/2312016 SC PA Parcel View: 07-20-31-506-0000-0350
Property Record Card
HI
Parcel: 07-20-31-506-0000-0350
Owner: BENDER MARY L
Property Address: 106 N SOMERSET CT SANFORD, FL 32773
Parcel Information
Parcel 07-20-31-506-0000-0350
Owner BENDER MARY L
Property Address 106 N SOMERSET CT SANFORD, FL 32773
Mailing 106 N SOMERSET CT SANFORD, FL 32773-7318
Subdivision Name BRYN HAVEN 1STREPLAT
Tax District S1-SANFORD
DOR Use Code 01-SINGLE FAMILY
Exemptions 00-HOMESTEAD(2000)
00.1
b Q
Seminole County GIS
Legal Description
LOT 35
BRYN HAVEN 1 ST REPLAT
PB 39 PGS 20 & 21
Taxes
Value Summary
2016 Working
Values
2015 Certified
Values
Valuation Method CosUMarket Cost/Market
Number of Buildings 1 1
Depreciated Bldg Value 92,944 89,688
Depreciated EXFT Value 1,800 1,800
Land Value (Market) 20,000 20,000
Land Value Ag
Just/MarketValue** 114,744 111,488
Portability Adj
Save Our Homes Adj 39,061 36,331
Amendment 1 Adj
P&G Adj 0 0
Assessed Value 75,683 75,157
Tax Amount without SOH: $1,447.59
2015 Tax Bill Amount $708.20
Tax Estimator
Save Our Homes Savings: $739.39
TRIM Notice Help
Does NOT INCLUDE Non Ad Valorem Assessments
Taxing Authority Assessment Value Exempt Values Taxable Value
County General Fund 75,683 50,000 25,683
Schools 75,683 25,000 50,683
City Sanford 75,683 50,000 25,683
SJWM(Saint Johns Water Management) 75,683 50,000 25,683
County Bonds 75,683 50,000 25,683
Sales
Description Date Book Page Amount Qualified Vac/Imp
WARRANTY DEED 9/1/1999 03733 1437 88,000 Yes Improved
WARRANTYDEED 7/1/1989 02094 0127 81,200 Yes Improved
Find Comparable Sales
Land
Method Frontage Depth Units Units Price Land Value
LOT 0.00 1 0.00 1 20,000.00 1 $20,000
Building Information
is bea/tfaln couni1ncorrecte UICK mere.
Description
Year Built
Fixtures Bed Bath Base Area Total SF Living SF Ext Wall Adj Value Repl Value Appendages
Actual/Effective
1 SINGLE 1989 8 3 2.0 1,480 1,968 1,480 CB/STUCCO 92,944 104,431 Description Area
http://parcel detai I .scpafl.org/Parcel D etai I lnfo.aspx?PID=07203150600000350 1/2
SCPA Parcel View: 07-20-31-506-0000-03508/23/2016
11 1 FAMILY
Permits
FINISH GARAGE
FINISHED
420.00
OPEN
PORCH 48.00
FINISHED
OPEN
PORCH 2O.00
FINISHED
Permit # Description Agency Amount CO Date Permit Date
02596 ADDITION - RESIDENTIAL SANFORD 5,880 5/9/2005
Extra Features
Description Year Built Units Value New Cost
SCREEN PATIO 1 12/1/1990 1 600 1,500
PATIO 1 6/1 /1990 1 200 500
FIREPLACE 12/1/1989 1 1,000 2,500
hUp:Hparceidetai l.scpafl.org/Parcel Detai I info.aspx?PID=07203150600000350 2/2
8/29/2016 Florida Building Code Online
1
r
77
0 0 0 0 a _
t -
BCIS Home Log In i User Registration i Hot Topics I Submit Surcharge i Stats & Facts I Publications i FBC Staff i BCIS Site Map I Links i •Search i
Florida
rd-Rd s
o _°°s Product Approval
USER: Public User
Product Approval Menu > Product or Application Search > Application List > Application Detail
FL #
Application Type
Code Version
Application Status
Comments
Archived
Product Manufacturer
Address/Phone/Email
Authorized Signature
Technical Representative
Address/Phone/Email
Quality Assurance Representative
Address/Phone/Email
Category
Subcategory
Compliance Method
Florida Engineer or Architect Name who developed
the Evaluation Report
Florida License
Quality Assurance Entity
Quality Assurance Contract Expiration Date
Validated By
Certificate of Independence
Referenced Standard and Year (of Standard)
Equivalence of Product Standards
Certified By
Sections from the Code
FL15216-R2
Revision
2014
Approved
U
InterWrap, Inc.
32923 Mission Way
Mission, NON -US 00000
551) 574-2939
mtupas@interwrap.com
Eduardo Lozano
elozano@interwrap.com
Eduardo Lozano
32923 Mission Way
Mission, NON -US 00000
778) 945-2891
elozano@interwrap.com
Roofing
Underlayments
Evaluation Report from a Florida Registered Architect or a Licensed
Florida Professional Engineer
U Evaluation Report - Hardcopy Received
Robert Nieminen
PE-59166
Intertek Testing Services NA, Inc.
11/17/2016
John W. Knezevich, PE
I U Validation Checklist - Hardcopy Received
FL15216 R2 COI 2015 01 COI Nieminen.odf
1507.2.3
1507.5.3
1507.8.3
1507.9.3
hUps://www.flori dabui Idi ng.org/pr/pr_app_dtl.aspx?param=wGEVXQwtDgv3yVVKJZ 1 QRAdhyl2u8kQGQyljaH hVei OpVSvxwSdCoQ%3d%3d 1 /2
8/29/2016 Florida Building Code Online
1507.9.5
T1507.8
Product Approval Method
Date Submitted
Date Validated
Date Pending FBC Approval
Date Approved
Summary of Products
Method 2 Option B
04/28/2015
04/29/2015
05/04/2015
06/23/2015
FL # Model, Number or Name Description
15216.1 RhinoRoof Underlayments Synthetic roof underlayments
Limits of Use Installation Instructions
Approved for use in HVHZ: No FL15216 R2 II 2015 04 FINAL ER INTERWRAP RHINOROOF FL15216-
R2. DidApprovedforuseoutsideHVHZ: Yes
Impact Resistant: N/A Verified By: Robert Nieminen PE-59166
Design Pressure: N/A Created by Independent Third Party: Yes
Other: See ER Section 5 for Limits of Use. Evaluation Reports
FL15216 R2 AE 2015 04 FINAL ER INTERWRAP RHINOROOF FL15216-
R2.pdf
Created by Independent Third Party: Yes
Back Next
Contact Us :: 2601 Blair Stone Road, Tallahassee FL 32399 Phone: 850-487-1824
The State of Florida is an AA/EEO employer. Copyright 2007-2013 State of Florida.:: Privacy Statement :: Accessibility Statement :: Refund Statement
Under Florida law, email addresses are public records. If you do not want your e-mail address released in response to a public -records request, do not send electronic
mail to this entity. Instead, contact the office by phone or by traditional mail. If you have any questions, please contact 850.487.1395. *Pursuant to Section
455.275(1), Florida Statutes, effective October 1, 2012, licensees licensed under Chapter 455, F.S. must provide the Department with an email address if they have
one. The emails provided may be used for official communication with the licensee. However email addresses are public record. If you do not wish to supply a
personal address, please provide the Department with an email address which can be made available to the public. To determine if you are a licensee under Chapter
455, F.S., please click here .
Product Approva l Accepts:
cCheck
Credit Card
Safe
https://www.flori dabui ldi ng.orglprlpr_app_c tl.aspx?param=wGEVXQwtDgv3yVVKJZ 1 QRAdhyl2u8kQGQylj aH hVeiOpVSvxwSdCoQ%3d%3d 2/2
01
EXTERIOR RESEARCH & DESIGN, LLC.
Certificate of Authorization #9503
353 CHRISTIAN STREET, UNIT #13
OXFORD, CT 06478
PHONE: (203) 262-9245
FAX: (203) 262-9243
EVALUATION REPORT
Interwrap, Inc. Evaluation Report 140510.02.12-112
32923 Mission Way FL15216-112
Mission, BC V2V-6E4 Date of Issuance: 02/17/2012
Canada Revision 2: 04/27/2015
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code
sections noted herein.
DESCRIPTION: RhinoRoof Underlayments
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product
changes or the referenced Quality Assurance documentation changes. Trinity) ERD requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity IERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 3.
Prepared by:
Robert J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCA ANE1983
The facsimile seal appearing was authorized by Robert Nieminen,
P.E. on 04/27/2015. This does not serve as an electronically signed
document. Signed, sealed hardcopies have been transmitted to the
Product Approval Administrator and to the named client
CERTIFICATION OF INDEPENDENCE:
1. TrinitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity) ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Underlayment
Compliance Statement: RhinoRoof Underlayments, as produced by Interwrap, Inc., has demonstrated compliance with the
intent of following sections of the Florida Building Code through testing in accordance with applicable sections of the following
Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein.
2. STANDARDS:
Section Properties Standard Year
1507.2.3, 1507.5.3, T1507.8, Unrolling, Breaking Strength, Pliability, Loss ASTM D226 2006
1507.8.3, 1507.9.3, 1507.9.5 on Heating
1507.2.3, 1507.5.3, 1507.8.3, Unrolling, Tear Strength, Pliability, Loss on ASTM D4869 2005
1507.9.3 Heating, Liquid Water Transmission,
Breaking Strength, Dimensional Stability
3. REFERENCES:
Entity Examination Reference Date
ITS (TST1509) Physical Properties 100539395COQ-006 10/27/2011
ITS (TST1509) Physical Properties 100539395COQ-002 10/27/2011
ITS (TST1509) Physical Properties 100539395COQ-006 03/14/2014
ITS (QUA1673) Quality Control Inspection Report 11/17/2014
4. PRODUCT DESCRIPTION:
4.1 RhinoRoof U20 is a multilayered polymer woven coated synthetic roof underlayment intended as an alternate to ASTM
D226, Type I or Type II felt or D4869 Type II felt. RhinoRoof Underlayment is available in 42-inch wide rolls, and can be
produced in various other sizes.
5. LIMITATIONS:
5.1
5.2
5.3
S.4
5.5
5.6
5.6.1
This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the Designer of
Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or
design guidance unless retained specifically for that purpose.
This Evaluation Report is not for use in the HVHZ.
Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory or test
report from accredited testing agency for fire ratings of this product.
RhinoRoof Underlayments may be used with any prepared roof cover where the product is specifically referenced
within FBC approval documents. If not listed, a request may be made to the AHJ for approval based on this evaluation
combined with supporting data for the prepared roof covering.
Allowable roof covers applied atop RhinoRoof Underlayments are follows:
TABLE S PROOF COVER OPTIONS,r
Asphalt Wood Shakes Slate or
Underlayment Nail -On Tile Foam -On Tile Metal
Shingles Shingles Simulated Slate
RhinoRoof U20 Yes No No Yes Yes No
Exposure Limitations:
RhinoRoof Underlayment shall not be left exposed for longer than 30-days after installation.
6. INSTALLATION:
6.1 RhinoRoof Underlayments shall be installed in accordance with Interwrap, Inc. published installation instructions
subject to the Limitations set forth in Section 5 herein and the specifics noted below.
6.2 Install RhinoRoof Underlayments in compliance with manufacturer's published installation instructions and the
requirements for ASTM D226, Type I or II or D4869, Type II underlayments in FBC Sections 1507 for the type of
prepared roof covering to be installed.
Exterior Research and Design,LLC. Evaluation Report 140510.02.12-R2
Certificate of Authorization #9503 FL15216-R2
Revision 2: 04/27/2015
Page 2 of 3
w
8.
9
QOTRINI-ry I ERD
6.3 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove
any dust and debris prior to application.
6.4 RhinoRoof U20:
6.4.1 Fasteners:
For exposure < 24 hours, corrosion resistant fasteners may be 1-inch roofing nails with a 3/8-inch diameter head, or
those noted in 6.4.2. The use of staples is prohibited.
For exposure > 24 hours up to maximum 30 days, corrosion resistant fasteners shall be minimum 1-inch diameter
plastic or metal cap nails or FBC HVHZ nails & 1-5/8" diameter tin caps (with the rough edge facing up). The use of
staples is prohibited.
6.4.2 Single Layer; Roof Slope > 4:12:
End (vertical) laps shall be minimum 6-inches and side (horizontal) laps shall be minimum 4-inches. Refer to Interwrap,
Inc. recommendations for alternate lap configurations and/or the use of sealant under certain conditions.
For exposure < 24 hours, use of every -other fastening location printed on the surface is acceptable. For exposure > 24
hours up to maximum 30-days, use of every fastening location printed on the surface is required.
When batten systems are to be installed atop the underlayment, the underlayment need only be preliminarily attached
pending attachment of the battens on the same day. Battens shall not be positioned over cap nails. If this occurs,
remove the cap nail and patch the hole in accordance with Interwrap published instructions.
6.4.3 Double Layer; 2:12 < Roof Slope < 4:12:
End (vertical) laps shall be minimum 12-inches and side (horizontal) laps shall be minimum half -sheet -width plus 1-inch.
Double layer application; begin by fastening a half -width plus 1-inch starter strip along the eaves. Place a full -width
sheet over the starter, completely overlapping the starter course. Continue as noted in 6.5, but maintaining minimum
half -width plus 1-inch side (horizontal) laps, resulting in a double -layer application.
BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product.
MANUFACTURING PLANTS:
Contact the manufacturer or the named CIA entity for information on plants covered under Rule 61G20-3 CIA requirements.
QUALITY ASSURANCE ENTITY:
Intertek Testing Services NA Inc.-ETL/Warnock Hersey — QUA1673; (604) 520-3321
Exterior Research and Design, LLC.
Certificate of Authorization #9503
END OF EVALUATION REPORT -
Evaluation Report 140530.02.12-112
FL15216-R2
Revision 2: 04/27/2015
Page 3 of 3
8/29/201,6 Florida Building Code Online
n
r• 0 0 0 0 + a
c
BCIS Home Log In i User Registration Hot Topics I Submit Surcharge Stats & Facts Publications FBC Staff BCIS Site Map Links •Search
Florida
Ao Product Approval
8ue rrt
USER: Public User
RRCaxral,-tm
Product Approval Menu > Product or Application Search > Application List > Application Detail
d+ FL # FL1956-R12
Application Type Editorial Change
Code Version 2014
Application Status Approved
Approved by DBPR. Approvals by DBPR shall be reviewed and ratified
by the POC and/or the Commission if necessary.
Comments
Archived U
Product Manufacturer TAMKO Building Products, Inc.
Address/Phone/Email PO Box 1404
Joplin, MO 64802
417) 624-6644 Ext2305
kerri_eden@tamko.com
Authorized Signature Kerri Eden
kerri—eden@tamko.com
Technical Representative Kerri Eden
Address/Phone/Email PO Box 1404
Joplin, MO 64802
417) 624-6644 Ext2305
kerri_eden@tamko.com
Quality Assurance Representative
Address/Phone/Email
Category Roofing
Subcategory Asphalt Shingles
Compliance Method Certification Mark or Listing
Certification Agency
Validated By
Referenced Standard and Year (of Standard)
Equivalence of Product Standards
Certified By
OFFICE
UL LLC
Robert J. M. Nieminen, PE
L-* Validation Checklist - Hardcopy Received
Standard
ASTM D3161
ASTM D3462
ASTM D7158
Year
2009
2009
2008
Product Approval Method Method 1 Option A
https://www.floridabuilding.orglprlpr_app_dtl.aspx?param=wGEVXQwtDgs%2fmGFoyT6raQ%2b%2bCX5ulUhEUshlcmF3nE3F2ytsDnaSgA%3d%3d 1/4
8/29/2016
U4
Date Submitted
Date Validated
Date Pending FBC Approval
Date Approved
Summary of Products
Florida Building Code Online
09/17/2015
10/06/2015
10/09/2015
FL # Model, Number Description
or Name
1956.1 Elite Glass -Seal A three tab asphalt shingle.
Limits of Use Certification Agency Certificate
Approved for use in HVHZ: No FL1956 R12 C CAC FL1956 R11 C CAC Tamko Sery Conf FL 1956 2015.pdf
FL1956 R12 C CAC UL certification 10-11-12.odfApprovedforuseoutside
HVHZ: Yes Quality Assurance Contract Expiration Date
Impact Resistant: N/A 09/17/2018
Design Pressure: N/A Installation Instructions
Other: Asphalt shingles shall be FL1956 R12 II Glass Seal Elite Glass Seal app inst.pdf
used only on roof slopes of 2:12 Verified By: Robert Nieminen 59166
or greater. Nails must be used Created by Independent Third Party: No
as the method of attachment. Evaluation Reports
Created by Independent Third Party:
1956.2 Glass -Seal A three tab asphalt shingle.
Limits of Use Certification Agency Certificate
Approved for use in HVHZ: No FL1956 R12 C CAC FL1956 R11 C CAC Tamko Sery Conf FL 1956 2015.0f
FL1956 R12 C CAC UL certification 10-11-12.ndfApprovedforuseoutside
HVHZ: Yes Quality Assurance Contract Expiration Date
Impact Resistant: N/A 09/17/2018
Design Pressure: N/A Installation Instructions
Other: Asphalt shingles shall be FL1956 R12 II Glass Seal Elite Glass Seal app inst.pdf
used only on roof slopes of 2:12 Verified By: Robert Nieminen PE 59166
or greater. Nails must be used Created by Independent Third Party: No
as the method of attachment. Evaluation Reports
Created by Independent Third Party:
1956.3 Heritage A dimensional asphalt shingle.
Limits of Use Certification Agency Certificate
Approved for use in HVHZ: No FL1956 R12 C CAC FL1956 R11 C CAC Tamko Sery Conf FL 1956 2015.pdf
FL1956 R12 C CAC UL certification 10-11-12.odfApprovedforuseoutside
HVHZ: Yes Quality Assurance Contract Expiration Date
Impact Resistant: N/A 09/17/2018
Design Pressure: N/A Installation Instructions
Other: Asphalt shingles shall be FL1956 R12 II Heritage D F J P apt) inst.odf
used only on roof slopes of 2:12 FL1956 R12 II Heritage F app inst.pdf
or greater. Nails must be used FL1956 R12 II Heritage T app inst.odf
as the method of attachment. Verified By: Robert J. M. Nieminen FL 59166
Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
1956.4 Heritage 30 A dimensional asphalt shingle.
Limits of Use Certification Agency Certificate
Approved for use in HVHZ: No FL1956 R12 C CAC FL1956 R11 C CAC Tamko Sery Conf FL 1956 2015.1)df
FL1956 R12 C CAC UL certification 10-11-12.pdfApprovedforuseoutside
HVHZ: Yes Quality Assurance Contract Expiration Date
Impact Resistant: N/A 09/17/2018
Design Pressure: N/A Installation Instructions
Other: Asphalt shingles shall be FL1956 R12 II heritage 30 app inst april 10.pdf
used only on roof slopes of 2:12 FL1956 R12 II heritage 30 app inst f april 10.1)df
or greater. Nails must be used Verified By: Robert Nieminen PE 59166
as the method of attachment. Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
1956.5 Heritage 50 A dimensional asphalt shingle.
Limits of Use Certification Agency Certificate
Approved for use in HVHZ: No FL1956 R12 C CAC FL1956 R11 C CAC Tamko Sery Conf FL 1956 2015.pdf
FL1956 R12 C CAC UL certification 10-11-12.odfApprovedforuseoutside
HVHZ: Yes Quality Assurance Contract Expiration Date
Impact Resistant: N/A 09/17/2018
Design Pressure: N/A Installation Instructions
Other: Asphalt shingles shall be FL1956 R12 II heritage 50 apo inst april 10.pdf
used only on roof slopes of 2:12 FL1956 R12 II heritage 50 apo inst f april 10.0df
or greater. Nails must be used Verified By: Robert Nieminen PE 59166
as the method of attachment. Created by Independent Third Party: No
Evaluation Reports
Created by Independent Third Party:
hfps://www.floridabuilding.orglprlpr_app_otl.aspx?param=wGEVXQwtDgs%2fmGFoyT6raQ%2b%2bCX5ulUhEUshlcmF3nE3F2ytsDnaSgA%3d%3d 2/4
Application Instructions for FORMERLY HERITAGE® 30
ffTA:IMK HEIRITAGED
BUILDING PRODUCTS LAMINATED ASPHALT SHINGLES
Dallas, TX • Frederick, MD . Joplin, MO a Phillipsburg, KS
THESE ARE THE MANUFACTURER'S APPLICATION INSTRUCTIONS FOR THE ROOFING CONDITIONS DESCRIBED.
TAMKO BUILDING PRODUCTS, INC. ASSUMES NO RESPONSIBILITY FOR LEAKS OR OTHER ROOFING DEFECTS RESULTING FROM
FAILURE TO FOLLOW THE MANUFACTURER'S INSTRUCTIONS. FAILURE TO FOLLOW THESE INSTRUCTIONS WILL ADVERSELY
AFFECT COVERAGE UNDER THE LIMITED WARRANTY. SEE THE LIMITED WARRANTY FOR DETAILS.
THIS PRODUCT IS COVERED BY A LIMITED WARRANTY, THE TERMS OF WHICH ARE PRINTED ON THE WRAPPER.
IN COLD WEATHER (BELOW 40°17), CARE MUST BE TAKEN TO AVOID DAMAGE TO THE EDGES AND CORNERS OF THE SHINGLES.
IMPORTANT: It is not necessary to remove the plastic strip from the back of the shingles.
I. ROOF BECK
These shingles are for application to roof decks consisting of plywood
or sheathing boards capable of receiving and retaining fasteners, and
to inclines of not less than 2 in. per foot. For roofs having pitches 2 in.
per foot to less than 4 in. per foot, refer to special instructions titled
Low Slope Application". For roofs having pitches greater than 21 in.
per foot, refer to special instructions titled "Mansard Roof or Steep
Slope Roof". Shingles must be applied properly. TAMKO assumes no
responsibility for leaks or defects resulting from improper application,
or failure to properly prepare the surface to be roofed over.
NEW ROOF DECK CONSTRUCTION: Roof deck must be smooth,
dry and free from warped surfaces. It is recommended that metal
drip edges be installed at eaves and rakes.
PLYWOOD: All plywood shall be exterior grade as defined by
APA - The Engineered Wood Association. Plywood shall be a
minimum of 3/8in. thickness and applied in accordance with the recommendations
of APA - The Engineered Wood Association. SHEATHING
BOARDS: Boards shall be well -seasoned tongue - and -
groove boards and not over 6 in. nominal width. Boards shall be
a 1 in. nominal minimum thickness. Boards shall be properly spaced
and nailed. 2.
VENTILATION Inadequate
ventilation of attic spaces can cause accumulation of moisture
in winter months and a build up of heat in the summer. These
conditions can lead to: 1.
Vapor Condensation 2.
Buckling of shingles due to deck movement. 3.
Rotting of wood members. 4.
Premature failure of roof. To
insure adequate ventilation and circulation of air, the ventilation system
must include inlets and outlets. This may be accomplished with a
combination of ridge and soffit vents or by using gable end vents. FHA
minimum property standards require one square foot of net free ventilation
area to each 150 square feet of space to be vented. This may
be reduced to one square foot of ventilation area per 300 square feet
if at least 40% and not more than 50% of venting is provided not
more than 3 feet below the ridge or if a Class 1 or 11 vapor barrier is
installed on the warm in winter side of the ceiling in climate zones 6,
7, and 8 as recommended by the 2012 International Residential Code.
For more information consult your design professional. If the ventilation
openings are screened, the total area should be doubled. IT
IS PARTICULARLY IMPORTANT TO PROVIDE ADEQUATE
VENTILATION. 8.
rASTENERS WIND
CAUTION: Extreme wind velocities can damage these shingles
after application when proper sealing of the shingles does not
occur. This can especially be a problem if the shingles are applied in
cooler months or in areas on the roof that do not receive direct sunlight.
These conditions may impede the sealing of the adhesive strips
on the shingles. The inability to seal down may be compounded by
prolonged cold weather conditions and/or blowing dust. In these situations,
hand sealing of the shingles is required. To insure quicker sealing,
apply 4 quarter -sized dabs of TAM -PRO® SBS Flashing Cement,
TAMKO or TAM -PRO® Plastic Roof Cement, or TAMKO Tam -
Seal Adhesive, meeting ASTM D 4586, Type 1, on the back of the
shingle 1 in. (25mm) and 13 in. (330mm) in from each side and 1
in. (25mm) up from the bottom of the shingle. Press shingle firmly into
the adhesive. For maximum wind resistance along rakes, install any
TAMKO starter shingle including sealant or cement shingles to the
underlayment and each other in a 4 in. (102mm) width of TAM - PRO®
SBS Flashing. Cement, TAMKO or TAM -PRO® Plastic Roof Cement,
or TAMKO Tam -Seal Adhesive. Caution: Apply ONLY a thin uniform
layer of adhesive less than21/8 in. (3mm) thick. Excessive amounts
can cause blistering of the shingles and may soften the asphalt
in certain underlayments resulting in the asphalt flowing, dripping
and staining. Shingles must also be fastened according to the
fastening instructions described below. Correct
placement of the fasteners is critical to the performance of the
shingle. If the fasteners are not placed as shown in the diagram and
described below, this will result in the termination of TAMKO's liabilities
under the Limited Warranty.. TAMKO will not be responsible for
damage to shingles caused by winds in excess of the applicable mph
as stated in the Limited Warranty. See Limited Warranty on the wrapper
or tamko.com for details. FASTENING
PATTERNS: Fasteners must be placed 6-1/8 in. from the
bottom edge of the shingle, penetrating through the common bond,
and located horizontally as follows: 1)
Standard Fastening Pattern. (For use on decks with slopes 2 in.
per foot to 21 in. per foot.) One fastener 1 in. from each end and one
13-1 /2 in. from each end of the shingle fora total of 4 fasteners. See
Standard Fastening Pattern illustrated below). STANDARD
FASTENING PATTERN BOND
NAILZONE
L
COMMON 6-
1 I I I I I I I I EXPOSURE 5-5/8' 1 "—
I h - 12-1 /2" 12-3/8"— Continued)
Central
District 220 West 4th St., Joplin, MO 64801 800-641-4691 09/19/14 Visit
Our Web Site at Northeast
District 4500 Tamko Dr., Frederick, MD 21701 800-368-2055 Southeast
District 2300 35th St., Tuscaloosa, AL 35401 800-228-2656 tamko.
eom Southwest District 7910 S. Central Exp., Dallas, TX 75216 800-443-1834 Western
District 5300 East 43rd Ave., Denver, CO 80216 800-530-8868 '
CONTINUED from page 1) FORMERLY HERITAGE® 30
ll llrl i HERITAGE®
SUIIa®ING PRODUCTS LAMINATED ASPHALT SHINGLES
Dallas, TX • Frederick, MD • Joplin, MO • Phillipsburg, KS
2) Mansard Fastening Pattern. (For use on decks with slopes
greater than 21 in. per foot.) One fastener 1 in. from each end and
one fastener 8-1/2 in. from each end and one fastener 16 in. from
each end for a total of 6 fasteners per shingle. (See Mansard and
High Wind Fastening Pattern illustrated below.)
MANSARD AND HIGH WIND WARRANTY FASTENING PATTERN
FASTENERS
NAIL ZONE
COMMON
BOND
6-1/8" EXPOSURE SS/d"
3) High Wind Warranty Fastening Pattern. (For High Wind Warranty
Application requirements) One fastener 1 in. from each end. One
fastener 8-1/2 in. from each end and one fastener 16 in. from each
end for a total of six (6) fasteners per shingle. In addition to this
shingle fastening pattern requirement for High Wind Application,
TAMKO also requires the use of TAMKO starter shingles including
sealant strip at eaves and rakes. Alternatively, along rakes, cement
shingles to the underlayment and each other in a 4 in. (102 mm)
width of TAM -PRO® SBS Flashing Cement, TAMKO or TAM -PROD
Plastic Roof Cement, or TAMKO Tam -Seal Adhesive. Caution: Apply
ONLY a thin uniform layer of adhesive less than 1/8 in. (3mm) thick.
Excessive amounts can cause blistering of the shingles and may
soften the asphalt in certain underlayments resulting in the asphalt
flowing, dripping and staining.
High Wind Application is offered on new construction or complete
tear -off applications only. It is not offered for recover applications.
If High Wind Application requirements are not followed, the High
WindApplication Warranty MPH, as stated on Table I in the Limited Warranty,
reverts to the Standard Application Wind Warranty MPH limit. (
See Mansard and High Wind Fastening Pattern illustrated above.)
NAILS:
TAMKO recommends the use of nails as the preferred method of
application. Standard type roofing nails should be used. Nail shanks
should be made of minimum 12 gauge wire, and a minimum head
diameter of 3/8 in. Nails should be long enough to penetrate 3/
4 in. into the roof deck. Where the deck is less than 3/4 in. thick, the
nails should be long enough to penetrate completely through plywood
decking and extend at least 1/8 in. through the roof deck. Drive
nail head flush with the shingle surface. Properly
Driven Improperly Driven Qt
3W min diameter untlerdrlven overdriven crooked t_
Asphen shinglesDecking
i
IX
nominal =\J straight,
good Penetration, Inadequate too deep, cuts Inadequate and
gush with shingle surface penetration Into shingle anchorage STAPLES:
If staples are used in the attaching process, follow the above
instructions for placement. All staples must be driven with pneumatic
staplers. The staple must meet the following minimum dimensional
requirements. Staples must be made from a minimum 16
gauge galvanized wire. Crown width must be at least 15/16 in. staple
crown width is measured outside the legs). Leg length should be
a minimum of 1-1/4 in. for new construction and 1-1/2 in. for reroofing
thus allowing a minimum deck penetration of 3/4 in. The Property
Driven Improperly Driven underdnven
overdriven crooked Asphalt
Shingles
Decking
crown
of the staple must be parallel to the length of the shingle. The
staple crown should be driven flush with the shingle surface. Staples
that are crooked, underdriven or overdriven are considered improperly
applied. CAUTION:
ALL FASTENERS MUST BE DRIVEN INTO THE NAIL
ZONE COMMON BOND AS SHOWN IN THE FASTENING PATTERN
DIAGRAMS. 4.
UNDCR16AYMENT UNDERLAYMENT:
An underlayment must be applied over the entire
deck before the installation of TAMKO shingles. Failure to add underlayment
can cause premature failure of the shingles which is not
covered by TAMKO's Limited Warranty. Products
which are acceptable for use as underlayment are: Asphalt
Saturated Felt Underlayments: SuperX
30T"' Underlayment TAMKO
No. 15 Asphalt Saturated Organic Felt Any
TAMKO non -perforated asphalt saturated organic felt A
non -perforated asphalt saturated organic felt which meets ASTM:
D226, Type I or II or ASTM D4869 Specialty
Underlayments: Tam -
Shield® Synthetic Underlayment or Synthetic Shield Underlayment
TAMKO
TW Metal and Tile Underlayment, TW Underlayment and
Moisture Guard Plus@ (additional ventilation may be required.
Contact TAMKO's Technical Services Department for
more information.) A
self-adhesive underlayment designed for use with asphalt shingles
which meets ASTM D1970. For
Asphalt Saturated Felt Underlayments: Apply
the felt when the deck is dry. On roof decks with slopes 4
in. per foot and greater apply the felt parallel to the eaves lapping
each course of the felt over the lower course at least 2
in. Where ends join, lap the felt 4 in. if left exposed, the felt may
be adversely affected by moisture and weathering. Laying of
the felt and the shingle application must be done together. For
All Other SDecial#y Underlayments: On
roof decks with slopes 4 in. per foot and greater apply the
underlayment parallel to the eaves in accordance with
underlayment written application instructions. The underlayment
should not be left exposed for a longer period of time
than is specified in the underlayments written application instructions.
The final roof covering must be installed before the
structure is exposed to adverse weather conditions, such as
wind driven rain, high wind, hail, ice storms, etc. (Continued) Central
District 220 West 4th St., Joplin, MO 64801 800-641-4691 09/19/14 Visit
Our Web Site at Northeast District 4500 Tamko Dr., Frederick, MD 21701 800-368-2055 Southeast
District 2300 35th St., Tuscaloosa, AL 35401 800-228-2656 tamko.
com Southwest District 7910 S. Central Exp., Dallas, TX 75216 800-443-1834 Western
District 5300 East 43rd Ave., Denver, CO 80216 800-530-8868 2
CONTINUED from page 2) FORMERLY HERITAGE® 30
11ILIT BUILDING
PRODUCTS 16AMINATED ASPHALT SHINGLES Dallas,
TX • Frederick, MD • Joplin, MO • Phillipsburg, KS In
areas where ice builds up along the eaves or a back-up of water from
frozen or clogged gutters is a potential problem, TAMKO's Moisture
Guard Plus", TW Metal and Tile Underlayment or TW Underlayment (
or any specialty eaves flashing product) may be applied
to eaves, rakes, ridges, valleys, around chimneys, skylights or
dormers to help prevent water damage. Contact TAMKO's Technical
Services Department for more information. Substitute
products as shingle underlayment should not be used 5.
APPLICATION INSTRUCTIONS STARTER
COURSE: A starter course may consist of TAMKO Shingle Starter,
TAMKO 10-inch Starter or self-sealing 3-tab shingles. If self- sealing
3-tab shingles are used, remove the exposed tab portion and install
with the factory applied adhesive adjacent to the eaves. Attach the
starter course with approved fasteners along a line parallel to and
1.5 in. to 3 in. above the eaves edge. The starter course should overhang
both the eaves and rake edges 1/4 in. to 3/8 in. if drip edge flashing
is not used along the eaves or rakes. If drip edge flashing is
present, install shingles even with the drip edge. For
maximum wind resistance a" rakes, in.tell any TAMKO
starer shingle I= udirig sealant a cement shingles b
underayment and eac h otller In a 4" (102 mm) width of TAM -
PROS SBS Flashing Cement, TAMKO or TAM -PROS Plastic
Roof Cement, or TAMKO Tam -Seal Adhesive. Underiayment Deck Esve
saturated asphalt1, or fell edgeDIP
Rake\\\
Faalenen \
1-12" I.3' fromlocarakehornrakeStanfirst
strip with 12 shingle Starter strips over -V Self-sealing Eeve Fastener Drip edge removed, than
follow with hal eaves and rakes adhesNe located ships in
order to offset with the 1/4" to 31W 9 no drip edge positioned 1-12" to 3" W shingle
course. Bearing is present. If drip along eaves from save edge edge flashing
is present; or rake edge instant shingles
even with drip edge.
SHINGLE APPLICATION:
Start the first course with a full size shingle and overhang
the rake edge 1/4 in. if drip edge is not present. If drip edge
is present, align shingle edge with drip edge flashing. Cut 10-3/
8 in. from a full shingle to form a shingle 29 in. long. Use this to start
the second course (see diagram below). Cut a 23 in. long shingle to
start the third course. Use the remaining 16-3/8 in. piece repeat 10.
3/8' W. courses 23
t
fr3/
8"' 23" rote `- Frrll.
5th course
4th course
3rd course
2nd course
1 at
counts 08" -- J23"
i
6,V8" 10-3/
8" of shingle
to start the fourth course and use the remaining 10-3/8 in. piece
to begin the fifth course. Continue up the rake in as many rows as
necessary using the same formula as outlined above. The butt
of the shingle should be aligned with the top edge of the sawtooth of
the underlying shingle for a 5-5/8 in, exposure (see shingle application
drawing illustrated on this panel). When you make your
final cut at the roof's edge, flip any pieces that are 8 in. or longer back
onto the roof. These pieces can be worked in anywhere without creating
zippers or color variations. NOTE: Do
not align joints of shingle courses when working in cut pieces. Joints
should be no closer than 4 in. from one another. 1Cut your
first course shingle to make 29" and a 10 3/8" length. Cutasecondshingletomakea23" and a /63ra"
length. 29' i
10 3/e' Al 2 0"
in application with a fun length shingle. Then layyour29", 23", 16 3/8 and 10 3/6" lengths. As you
can see, three shingles with two cuts make two
courses. 3. Continue
working your way across the roof. When you make your final cutattheroorsedge, flip any pieces that are 6" or longer back onto
the root. These pieces can be worked in anywhere without creating zippers
or color variations. NOTE:. Do
not align Joints ofshingle courses when working In cut plecas. Joints
should be no closer than 4" from one another. S. LOW SLOPE
APPLICATION On pitches 2
in. per foot to 4 in. per foot cover the deck with two layers of underlayment.
Begin by applying the underlayment in a 1/2-sheet
width along the eaves and overhanging the drip edge by 1/4
to 3/4 in. Place a full -sheet width over the 1/2-sheet width starter piece, completely
overlapping it. All succeeding courses will be positioned to
overlap the preceding course by 1/2-sheet width. If winter temperatures
average 25°F or less, thoroughly cement the laps of
the entire underlayment to each other with TAM -PRO or TAMKO Plastic
Roof Cement from eaves and rakes to a point of a least
24 in. inside the interior wall line of the building. As an alternative, TAMKO's
Moisture Guard Plus®, TW Metal and Tile Underlayment, or TW
Underlayment self -adhering underlayment may be used
in lieu of the cemented felts. 9. MANSARD ROOF
OR STEEP SLOPE ROOF If the slope
exceeds 21 in. per foot (601, each shingle must be sealed with TAM -PRO®
SBS Flashing Cement, TAMKO or TAM -PRO® Plastic Roof Cement,
or TAMKO Tam -Seal Adhesive immediately upon installation. Quarter -
sized dabs of cement or adhesive must be applied to
shingles with a 5-5/8 in. exposure, use 6 fasteners per shingle. See Section
3 for the Mansard Fastening Pattern. Continued) Central District
220
West 4th St., Joplin, MO 64801 800-641-4691. 09/19/14 Visit Our Web
Site at Northeast District 4500 Tamko Dr., Frederick, MD 21701 800-368-2055 Southeast District 2300
35th St., Tuscaloosa, AL 35401 800-228-2656 tamko.com Southwest
District 7910 S. Central Exp., Dallas, TX 75216 800-443-1834 Western District 5300
East 43rd Ave., Denver, CO 80216 800-530-8868 3
CONTINUED from page 3) FORMERLY HERITAGE® 30
t 1, IF
1 '
zll , 41P plt
Dallas, TX • Frederick, MD • Joplin, MO • Phillipsburg, KS
8. RR -ROOFING
Before re -roofing, be certain to inspect the roof decks. All plywood shall
meet the requirements listed in Section 1.
It is not recommended to install laminated asphalt shingles directly
over existing laminated shingles due to the unevenness of the existing
multi -layered shingles. The performance of the sealant feature may be
compromised, preventing the shingles from sealing properly. It is
acceptable to install laminated shingles over existing three -tab strip
shingles which are flat and essentially intact. Nail down or remove curled
or broken shingles from the existing roof. Replace all missing shingles
with new ones to provide a smooth base. Shingles that are buckled
usually indicate warped decking or protruding nails. Hammer down all
protruding nails or remove them and refasten in a new location. Remove
all drip edge metal and replace with new.
If re -roofing over an existing roof where new flashing is required to
protect against ice dams (freeze/thaw cycle of water and/or the backup
of water in frozen or clogged gutters), remove the old roofing to a point
at least 24 in. beyond the interior wall line and apply TAMKO's Moisture
GuardPlus® , TW Metal and Tile Underlayment, or TW Underayment. Contact
TAMKO's Technical Services Department for more information. Measurements
will vary when nesting over an existing 5 in. exposure single
roof: Call TAMKO Technical Services for further information. The
nesting procedure described below is the preferred method for reroofing
over existing metric size shingles with a 5-5/8 in. exposure. See
description below: Starter
Course: Remove the tabs and an additional portion from the head
of a full size shingle so that its height is equal to the exposure of the
existing shingles. Position the resulting strip over the existing roof edge (
with the factory -applied adhesive strip along the eaves). Cut approximately
6 in. from the rake end and apply the remaining portion at the
eaves. Continue the starter strip by applying full length shingle strips cut
to height as above, evenly along the existing roof at the eaves. The existing
roof should overhang the eaves far enough to carry water off
into the gutter. If this is not the case, cut and apply the starter strip
so that it will provide sufficient overhang for proper drainage. First
Course: Remove an amount from the butt edge of afull-size shingle so
that the remaining portion of the shingle fits between the butts of the existing
third course. This course must also be applied evenly along the eaves
edge of the new starter strip. Second
and Succeeding Courses: Remove 10-3/8 in. from the rake end
of the first shingle in the second course, and continue with full width
shingles for the remainder of the course, placing the top edge of each
new shingle against the butt edge of the old shingle in the course above.
This method should create an exposure of 5-5/8 in. afterthe first course.
When beginning the succeeding courses continue to follow the Heritage
application instructions. (See section 5). 9.
VA666Y APP6ICATION Over
the shingle underlayment, center a minimum 36 in. wide sheet of Moisture
Guard Plus®, TW Metal & Tile Underlayment, or a minimum 50
lb. roll roofing in the valley. Nail the underlayment only where necessary
to hold it in place and then only nail the outside edges. IMPORTANT:
PRIOR TO INSTALLATION WARM SHINGLES TO PREVENT
DAMAGE WHICH CAN OCCUR WHILE BENDING SHINGLES
TO FORM VALLEY. After
valley flashing is in place: Apply
the first course of shingles along the eaves of one of the intersecting
roof planes and across the valley. Note:
For proper flow of water over the trimmed shingle, always start
applying the shingles on the roof plane that has the lower slope
or less height. Extend
the end shingle at least 12 in. onto the adjoining roof. Apply
succeeding courses in the same manner, extending them across
the valley and onto the adjoining roof. Press
the shingles tightly into the valley. Use
normal shingle fastening methods. Note:
No fastener should be within 6 in. of the valley centerline, and
two fasteners should be placed at the end of each shingle crossing
the valley. To
the adjoining roof plane, apply one row of shingles vertically facing
the valley and 2 in. back from the valley centerline. Note:
For a neater installation, snap a chalkline over the shingles
for guidance. To
complete the valley, apply shingles on the adjoining roof plane
by positioning the tip of the first shingle of each row at the
2 in. point from the centerline where the edge of the vertical shingle
has been applied, covering the vertical shingle. Minimum
36' wide sheet of
Moisture Guard Plus, TW
Metal & " Tile
or501b. or heavier
roll roofing Underlayment
Valley
centerline 1
Extra nail in end
of shingle Place
Up of shingle on the edge of the
vertical shingle, 2 Inches back from
valley centerline and covering the
vertical shingle. Extend
end shingle 12'-
18'beyond valley
centerline No
fasteners within 6'
of centerline FOR
ALTERNATE VALLEY APPLICATION METHODS, PLEASE CONTACT
TAMKO'S TECHNICAL SERVICES DEPARTMENT AT 800-
641-4691. Continued)
Central
District 220 West 4th St., Joplin, MO 64801 800-641-4691 09/19/14 Visit
Our Web Site at Northeast District 4500 Tamko Dr., Frederick, MD 21701 800-368-2055 Southeast
District 2300 35th St., Tuscaloosa, AL 35401 800-228-2656 tamkoxom
Southwest District 7910 8. Central Exp., Dallas, TX 75216 800-443-1834 Western
District 5300 East 43rd Ave., Denver, CO 80216 800-530-8868 4
CONTINUED from page 4) FORMERLY HERITAGE® 30
1-1-AMINUI HEIRRIPARGE6
BUILDING PRODUCTS LAMINATED ASPHALT SHINGLES
Dallas, TX • Frederick, MD • Joplin, MO e Phillipsburg, KS
10. 81P AND RIDGE FASTENING DETA16
Apply the shingles with a 5-1/8 in. exposure beginning at the bottom
of the hip or from the end of the ridge opposite the direction of the
prevailing winds. Secure each shingle with one fastener on each side,
5-5/8 in. back from the exposed end and 1 in. up from the edge.
TAMKO recommends the use of TAMKO Hip & Ridge shingle
products. Where matching colors are available, it is acceptable to
use TAMKO's Elite Glass -Seal shingles cut down to 12 in. pieces.
Fasteners should be 1 /4 in. longer than the one used for shingles
IMPORTANT. PRIOR TO INSTALLATION, CARE NEEDS TO BE
TAKEN TO PREVENT DAMAGE WHICH CAN OCCUR WHILE
BENDING SHINGLE IN COLD WEATHER.
Direction of prevailing wind
Start 5-1/8" exposure
7
here—
r'flilfl
here
i 1
THESE ARE THE MANUFACTURER'S APPLICATION
INSTRUCTIONS FOR THE ROOFING CONDITIONS
DESCRIBED. TAMKO BUILDING PRODUCTS, INC. ASSUMES
NO RESPONSIBILITY FOR LEAKS OR OTHER ROOFING
DEFECTS RESULTING FROM FAILURE TO FOLLOW THE
MANUFACTURER'S INSTRUCTIONS. FAILURE TO FOLLOW
THESE INSTRUCTIONS WILL ADVERSELY AFFECT COVERAGE
UNDER THE LIMITED WARRANTY. SEE THE LIMITED
WARRANTY FOR DETAILS. IF YOU HAVE ANY QUESTIONS
REGARDING THESE APPLICATION INSTRUCTIONS, PLEASE
CONTACT TAMKO'S TECHNICAL SERVICES DEPARTMENT AT
800-641-4691.
Information included in these application instructions was current at time of printing. To
obtain a copy of the most current version of these application instructions, visit us online
at tamko.com or call us at 800-641-4691.
TAMKOO, Moisture Guard Plus®, Tam -Shield®, TAM -PROS and Heritage® are registered
trademarks and SuperX 30 is a trademark of TAMKO Building Products, Inc.
Central District 220 West 4th St., Joplin, MO 64801 800-641-4691 09/19/14
Visit Our Web Site at Northeast District 4500 Tamko Dr., Frederick, MD 21701 800-368-2055
Southeast District 2300 35th St., Tuscaloosa, AL 35401 800-228-2656
tamko.com Southwest District 7910 S. Central Exp., Dallas, TX 75216 800-443-1834
Western District 5300 East 43rd Ave., Denver, CO 80216 800-530-8868 5
JP69909
CITY OF SANFORD BUILDING SERVICES
Residential Re -Roof
Hurricane Mitigation Inspection Affidavit
Permit #: f A4A
I, hereby acknowledge that I personally inspected
t Roof deck nailing and/or 4/Secondary water barrier work
J. Douglas Lanier
at 10l N • Wmwsck Wkf 6wwd 6CC 11`J
and have determined that the work
Job Site Address)
was done according to the Hurricane Mitigation Retrofit Manual. (based on 553.844 F.S.)
I certify that my statements herein are true and accurate to the best of my belief and that I fully
understand that making any false statements in writing with the intent to mislead a public servant in the
performance of his or her official duty shall constitute a misdemeanor of the second degree pursuant to
Section 837.06 F.S.
Signature of Contractor
J. Douglas Lanier
Printed Name of Contractor
q-0?0-A
Date
CCC058022
License #
License Type: i., General L Building Residential x Roofing Contractor
or any individual certified in accordance with F.S. 468 to make such an inspection.
STATE OF FLORIDA COUNTY OF Seminole
Sworn to (oraffirmed) and subscribed before me this ZDdayof %/ , 20 16 , by
J. Dou a anier who is 31 Personally Known to me or has L Produced (type of
identi as identification.
EAL)
Signatur of No ry Public --'
State of Florida Y" : STEPHANIE JOY WILLIAMS
Stephanie J. Williamsp MY COMMISSION #EE847705
Print/Type/Stamp Name EXPIRES october 29, 201s of
Notary Public (407) 398 . F. 9: Nosa----Y e
rom