136 Wilson Bay Ct - BR18-004556 - REROOFS 1
CITY OF
ORD
n
FIRE UPARTMENT
Building & Fire Prevention Division
PERMIT APPLICATION
Application No: a - 4 S (Q
Documented Construction Value: $ I 3`J c 2
Job Address: 136 Wilson Bay Ct. Sanford, FL 32771 Historic District: Yes No
Parcel ID: 22-19-30-503-0000-2570 Residential Commercial
Type of Work: New Addition Alteration RepairDemo Change of Use Move Description
of Work: REMOVE EXISTING ROOF DOWN TO DECK. INSTALL NEW UNDERLAYMENT
AND SHINGLES TO LOCAL CODE. Plan
Review Contact Person: Title: Phone:
y0-I-2(6LI -1-13lb Fax: Name
Noll, Gary Street:
136 Wilson Bay Ct. Email:
C)Mi-(X('mi f }i61rw r'(n114, LO (1 Property
Owner Information City,
State Zip: SANFORD, FL 32771 Name
OAK CREST CONTRACTING Phone:
8159783537 Resident
of property? : Yes Contractor
Information Street:
115 TIMBERLACHEN CIR, STE 1013 City,
State Zip: LAKE MARY, FL 32746 Name:
Street:
City,
St, Zip: Phone:
407-284-1738 Fax:
State
License No.: CCC1330407 Architect/
Engineer Information Phone:
Fax:
E-
mail: Bonding
Company: Mortgage Lender: Address:
Address: WARNING
TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING
TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDED
AND POSTED ON THE JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING,
CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT.
Application
is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced
prior to the issuance of a permit and that all work will be performed to meet standards of all laws regulating construction in
this jurisdiction. I understand that a separate permit must be secured for electrical work, plumbing, signs, wells, pools, furnaces,
boilers, heaters, tanks, and air conditioners, etc. FBC
105.3 Shall be inscribed with the date of application and the code in effect as of that date: 6"' Edition (2017) Florida Building Code Revised:
January 1, 2018 Permit Application
NOTICE: In addition to the requirements of this permit, there may be additional restrictions applicable to this property that may be
found in the public records of this county, and there may be additional permits required from other governmental entities such as water
management districts, state agencies, or federal agencies.
Acceptance of permit is verification that I. will notify the owner of the property of the requirements of Florida Lien Law, FS 713.
The City of Sanford requires payment of a plan review fee at the time of permit submittal. A copy of the executed contract is required
in order to calculate a plan review charge and will be considered the estimated construction value of the job at the time of submittal.
The actual construction value will be figured based on the current ICC Valuation Table in effect at the time the permit is issued, in
accordance with local ordinance. Should calculated charges figured off the executed contract exceed the actual construction value,
credit will be applied to your permit fees when the permit is issued.
OWNER'S AFFIDAVIT: I certify that all of the foregoing information is accurate and that all work will
be done in compliance with all applicable laws regulating construction and zoning.
Signature of er/Agent Date
Agent's Name
Julian Olajos
COMMISSION O GG259135
i EXPIR : Se t16 C22
to Me or
D ype o L cce41S
Si re ofcontrac o /Agent Date
s)r; 1(
Print Contractor/Agent's Name
Signature of -• te of FILMS' Ney GQ'c
P I"'7 Gois ICMISSINI
S GG22 M 4;..
EXPIRES: June 19, 2022 lttnt
Aston Notary Contractor/
Agent is Personally Known to Me or Produced
ID Type of ID BELOW
IS FOR OFFICE USE ONLY Permits
Required: Building Electrical Mechanical Plumbing Gas Roof Construction
Type: Total
Sq Ft of Bldg: Occupancy
Use: Min.
Occupancy Load: New
Construction: Electric - # of Amps Flood
Zone: of
Stories: Plumbing - #
of Fixtures Fire
Sprinkler Permit: Yes No # of Heads Fire Alarm Permit: Yes No APPROVALS:
ZONING: UTILITIES: WASTE WATER: ENGINEERING:
COMMENTS:
FIRE:
BUILDING: Revised:
January 1, 2018 Permit Application
OAK CREST CONTRACTING, INC.
115 Timberlachen Cir #1013
Lake Mary, FL 32746 oakcrest.com
Contractor Registration: CCC1330407
PHONE: 407-284-1738 FAX:866-648-8193
No Risk' Guarantee!
REP: _ 'J (Ck 1 v lGl{OS
SOLICITOR'S LIC:
PHONE: --I uu--
ll ` L4 CR I'l----------------
OWNER I`
t 1
DATE
6 i {-I`
EMAIL ADDRESS
j 4 OeAio)Wlr` v[T3Sa co .
STREET CELL PHONE WORK PHONE
3 6 1.50..E r- 1S" T7,K 537
CITY
5h :/
ST-TE ZI
7 71
HOME PHONE
W erebySJ}U+ ml SCO a Of WOrIC fOr: FLORIDA CONSTRUCTION LIEN. ACCORDING TO FLORIDA'S CONSTRUCTION
r Off1t}a rsQ G LIEN LAW (SECTIONS 713.001-713.37, FLORIDA STATUTES), THOSE WHO WORK
ON YOUR PROPERTY OR PROVIDE MATERIALS AND ARE NOT PAID -IN -FULL
f squares off — L u Iew RAVE A RIGHT TO ENFORCE THEIR CLAIM FOR PAYMENT AGAINST' YOURecoverroofwithL—+ wLc /y" C. PROPERTY. THIS CLAIM IS KNOWN AS A CONSTRUCTION LIEN. IF YOUR
of squares on t-L WCW Y
Ingle/COIOf G r ,
er'61tect
CONTRACTOR OR A SUBCONTRACTOR FAILS TO PAY SUBCONTRACTORS, SUB-
SUBCONTRACTORS OR MATERIAL SUPPLIERS OR NEGLECTS TO MAKE OTHER
LEGALLY REQUIRED PAYMENTS, THE PEOPLE WHO ARE OWED THE MONEY
property as eded daily -,n,
eking OSB
as
others "6' '' `W j
MAY LOOK TO YOUR PROPERTY FOR PAYMENT, EVEN IF YOU HAVE PAID
YOUR CONTRACTOR IN FULL. IF YOU FAIL TO PAY YOUR CONTRACTOR, YOUR
nderlayment 15 lb. 30 lb. Others y''1 1Q.,*iCCONTRACCORetaledgecolorUUtK
Iley aAA Wcuic-1 sil i Ci closed open
MAY ALSO HAVE A LIEN ON YOUR PROPERTY. THIS MEANS IF A
LIEN IS FILED, YOUR PROPERTY COULD BE SOLD AGAINST YOUR WILLTO PAY
FOR LABOR, MATERIALS OR OTHER SERVICES THAT YOUR CONTRACTOR OR A
SUBCONTRACTOR MAY HAVE FAILED TO PAY. TO PROTECT YOURSELF, YOU
Ridge GOew standard enhanced SHOULD STIPULATE IN THIS CONTRACT THAT BEFORE ANY PAYMENT ISaandils1, rL C-Lo(V - Open eaves
Ipe flashing IVC.c v 3/1RELEASEead
enti lation box U . ridge other o-F4= v , c k 4-
MADE, YOUR CONTRACTOR IS REQUIRED TO PROVIDE YOU WITH A WRITTEN
OF LIEN FROM ANY PERSON OR COMPANY THAT HAS PROVIDED TO
YOU A "NOTICE TO OWNER." FLORIDA'S CONSTRUCTIONN LIEN LAW IS
COi4IPLEX, AND IT IS RECOMMENDED THAT YOU CONSULT AN ATTORNY.
eal around all vents, pipes and flashings FLORIDAHOMEOGVNIERS' CONSTRUCTION RECOVERY FUND. PAYMENT MAY
ce and water shield to local code BE AVAILABLE FROM THE FLORIDA HOMEOWNERS' CONSTRUCTION
Furnish all materials, labor an ecessary permits
vellve Instructions left right otherrYg
aul off construction debris
RECOVERY FUND IF YOU LOSE MONEY ON A PROJECT PERFORMED UNDER
CONTRACT, WHERE THE LOSS RESULTS FROM SPECIFIED VIOLATIONS OF
FLORIDA LAW BY LICENSED CONTRACTOR. FOR INFORMATION ABOUT THE
RECOVERY FUND AND FILING A CLAIM, CONTACT THE FLORIDA
year limited warranty CONSTRUCTION INDUSTRY LICENSING BOARD AT THE FOLLOWING
oil magnet through yard
TELEPHONE NUMBER AND ADDRESS: CILB, 1940 North Monroe SL, Ii42,'rallahassee,
FL32399.
Lien waivers provide upon final payment ANY CLAIMS FOR CONSTRUCTION DEFECTS ARESUBJECT TO THE NOTICE AND
CURE PROVISIONS OF CHAPTER 558, FLORIDA STATUTES.
BUYER'S RIGHT TO CANCEL: This is a home solicitation sale, and if you do not want the goods or services, you may cancel this Agreement by providing written notice to the seller in
person, by telegram, or by mail. This notice must indicate thatyou do not want the goods or services and must be delivered or postmarked before midnight on the third business day after
you sign this Agreement. If you cancel this Agreement, the seller may not keep all or part of any cash down payment. By signing this Agreement, you agree that you have also been
provided notice of this right to cancel orally in addition to the writing contained herein.
Customer's signature below signifies acceptance ofall terms and conditions of this Agreement, including all terms on the reverse side hereof.
Terms: This Agreement is contingent upon insurance company price and approval. This Agreement does not obligate the Customer or Company in any way unless it is
approved by Customer's insurance company and accepted by Company. Company proposes to furnish all permits, labor and materials to complete the above
replacement or repair for the estimated sum of total cost below or the price otherwise agreed upon with Customer's insurance company (the "Agreed Price"). Customer
authorizes Company to obtain labor and materials in accordance with the Agreed Price and the specifications set forth herein to accomplish the above replacement or
repair. Customer understands that Company does not work for Customer's insurance company and/or the insurer for the property, and that Customer alone has the
authority to authorize Company to perform the above replacement or repair. Customer's signature on this Agreement also signifies acceptance of all terms and
conditions of this Agreement, including all terms on the reverse side hereof. In situations where supplements for additional work are necessary outside of the original,-
scope of work (ex. additional layers or measurements), Company will seek approval from insurance company. Customer's out of pocket expense not to exceed
deductible plus upgrades for non -insurance related claim items.
Payment Method: Payment Upon Completion of Each Trade. Check or money order made payable to Oak Crest. Cash will not bean acceptable form of payment.
Emergency Tarps
Insurance Proceeds
Cash/ Financing
Total cost (tax included)
Acceptance by Owner of property By:
Representative Signature By:
Estimated Project Start Date:
Estimated Date of Completion::
Date:1 '`/ _
Date: FL
Grant Maloy, Clerk Of The Circuit Court & Comptroller Seminole County FL
Inst #2018125913 Book:9243 Page:414; (1 PAGES) RCD: 11/2/2018 4:00:49 PM
REC FEE $10.00
THIS INSTRUMENT PREPARED BY:
Name: Julian Olalos
Address: 115 Tlmberiachen Circle, Suite 1013
Lake Mary, FL 32746
NOTICE OF COMMENCEMENT
Permit Number.
Parcel 10 Number. 22-19-30-503-0000-2570
The undersigned hereby gives notice that improvement will be made to certain real property, and in accordance with Chapter 713. Florida Statutes, the
following Information Is provided in this Notice of Commencement. s
1. DESCRIPTION OF PROPERTY: (Legal description of the property and street address ifavailable)
LOT 257 PRESERVE AT LAKE MONROE UNIT 2 PB 66 PGS 10 & 11
2. GENERAL DESCRIPTION OF IMPROVEMENT:
REMOVE EXISTING ROOF TO DECK. INSTALL NEW UNDERLAYMENT AND ROOF TO CODE.
3. OWNER INFORMATION OR LESSEE INFORMATION IF THE LESSEE CONTRACTED FOR THE IMPROVEMENT:
Name and address: NOLL GARY 136 WILSON BAY CT SANFORD FL 32771
Interest in property. OWNER
Fee Simple Title Holder (if other than ownerlisted above) Name:
4. CONTRACTOR: Name: OAK CREST CONTRACTING Phone Number. 407-284-1738
Address: 115 TIMBERLACHEN CIR, STE 1013 LAKE MARY, FL 32746
5. SURETY (If applicable, a copy of the payment bond Is attached): Name:
Address: Amount of Bond:
6. LENDER: Name: Phone Number.
Address:
7. Persons within theState of Florida Designated by Owner upon whom notice orother documents maybe served as provided by Section
713.13(1)(a)7., Florida Statutes.
Name: Phone Number.
Address:
8. In addition, Owner designates of
to receive a copy of the Llenor's Notice as provided In Section 713.13(1)(b), Florida Statutes. Phone number.
9. Expiration Date of Notice of Commencement (The expiration is 1 year from date of recording unless a different date Is specified)
WARNING TO OWNER: ANY PAYMENTS MADE BY THE OWNER AFTER THE EXPIRATION OF THE NOTICE OF COMMENCEMENT ARE
CONSIDERED IMPROPER PAYMENTS UNDER CHAPTER 713. PART I, SECTION 713.13, FLORIDA STATUTES, AND CAN RESULT IN YOUR
PAYING TWICE FOR IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDED AND POSTED ON THE
JOB SITE BEFORE THE FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY
BEFORE COMMENCING WORK OR RECORDING YOUR NOTICE OF COMMENCEMENT.
9 of Owner Lessee or Owrera or Leased, (PAN NWM and Provide Signab Y6'n4&f0rtee)
AuVatwdOnced08rae= Pa rmNanWw)
State of '-- (A9y`i a CA County of t f' (M (Ad(4 The
foregoing instrument was acknowledged before me this I. ` day off by
N-0Who Is personally known tome D OR who
has produced Identificationn7 typeof identification produced:. L Uy6r L— `ceVIC-G Julian
Olaeos 6 ;,
l OMM 581QN 6G 135 N EXPIRES.
Sept 16, 2022 ; Bonded
ihru Asm NoUry wl
MJ
CONSTRUCTION MATERIALS
TECHNOLOGIES
October 27, 2017
IKO Industries, Ltd
120 Hay Rd.
Wilmington, DE 19809
Re: FBC FL7006
Sir(s),
PRI Construction Materials Technologies has completed a technical review and attached sealed shingle
instructions in compliance the 2017 Florida Building Code.
This review was completed based on the receipt of following evidence from IKO Industries, Ltd:
1) IKO Shingle Application Instructions — 3-Tab Shingles
EN-3Tab_Appins_8AGXEFS-2012-11_reformatted 2013-02-rev07/13-Florida)
2) IKO Laminated Shingles Application Instructions
EN -Laminated Appins_8TTEFS-2012-04 reformatted 2013-02-rev07/13-Florida)
3) IKO Hip and Ridge 12 Application Instructions
EN-HipandRidge12_3HRTri-2013-08_reformatted 2013-08)
4) IKO Leading Edge Plus Shingle Application Instructions
EN-3LEP-Tri-2012-06—reformatted 2013-03)
5) ASTM D3161 Test Report (FM Approvals Project No. 3040947)
The attached instructions should be used in conjunction with the published manufacturer's application
instructions and applicable code. In the event the instructions conflict, these instructions shall govern.
Statement of Independence: PRI Construction Materials Technologies and/or Duc T. Nguyen, FL P.E. do not
have nor plan to acquire a financial interest in any company manufacturing or distributing products for which
the test reports are issued.
r°
Signed: 4zz,Signed:
Brad Gr ybo ki
Managing rector
Date: October 27, 2017 Date
Attachments: A) IKO Shingle Application Instructions - 3-Tab
B) IKO Laminated Shingles Application Instructions
C) IKO Hip and Ridge 12 Application Instructions
D) IKO Leading Edge Plus Application Instructions
IKO-187-02-01
Duc T./Nuu en
Florida Re`gMlArred ProfessionaEngineer
P.E. Number: 65034
October 27. 2017
PRI Construction Materials Technologies, LLC. 6412 Badger Drive Tampa, FL33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: materialstestng@pdcmt.com WebSite: http:llwww.pricmLcom
IKO
Installation Instructions for
Asphalt Shingles
Page 2 of 5
IKO Shingle Application Instructions — 3-Tab Shingles
ASTM D3161, Class F — IKO Marathon 26 AR and CRC Superglass M26AR)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
ROOF DECK: Solidly sheathed and fastened deck conforming to 2017 FBC.
UNDERLAYMENT: Applied in accordance with building code requirements. For areas where the roof slope is
less than 4" per foot down to 2" per foot, use 2 layers of underlayment conforming to building code
requirements, the first sheet overlapping the eave protection by 19", followed by full 36" widths overlapping
each preceding course by 19" or other Approved underlayments in accordance with the qualified application
instructions. For areas where the roof slope is 4" per foot or greater, cover the deck with one ply of
underlayment laid parallel to the eaves, with 2" horizontal laps and 4" end laps. Apply metal drip edges on top
of any underlay along rake edges and directly to the deck along eaves in accordance with building code
requirements.
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8" diameter heads, long
enough to penetrate through plywood or 3/4" into boards. Use 4 nails per shingle placed 6-1/8" above the butt
edge, approx. 1" and 13" from each end and 1/2" above each cutout. Drive nails straight so that nail head is
flush with, but not cutting into shingle surface.
NAILING ON STEEP SLOPES: For steep slopes of 21" per foot (600) or more, use 6 nails per shingle placed
as shown below. Ensure that no nail is within 2" of a joint/cutout of the underlying shingle. Seal down each
shingle at time of application with three 1" diameter (approx. size and thickness of a quarter) spots of asphalt
plastic cement placed under the shingle 2" above the bottom edge and equally spaced along the shingle.
Apply plastic cement in moderation since excessive amounts may cause blistering. CAUTION: Shingles
should seal to the underlying course when the factory applied asphalt sealant is sufficiently warmed by the
heat of direct sunlight.
EXPOSURE: Installed shingles shall have a maximum average exposure of 5-5/8".
STEEP SLOPES
1-1fZ' 1-12"
t
i SEALING STRIP — — — — —
NAILS NAILS
DO NOT NAIL INTO OR ABOVE THE SEALING STRIP
PRI Construction Materials Technologies, LLC. 6412 Badger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: matedaistesting@pricmt.com WebSite: htlp:/Avww.pdcmtcom
IKO
Installation Instructions for
Asphalt Shingles
Page 3 of 5
IKO Laminated Shingles Application Instructions
ASTM D3161, Class F — Cambridge, Cambridge HD, and CRC Biltmore AR)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
ROOF DECK: Solidly sheathed and fastened deck conforming to 2017 FBC.
UNDERLAYMENT: Applied in accordance with building code requirements. For areas where the roof slope is
less than 4" per foot down to 2" per foot, use 2 layers of underlayment conforming to building code
requirements, the first sheet overlapping the eave protection by 19", followed by full 36" widths overlapping
each preceding course by 19" or other Approved underlayments in accordance with the qualified application
instructions. For areas where the roof slope is 4" per foot or greater, cover the deck with one ply of
underlayment laid parallel to the eaves, with 2" horizontal laps and 4" end laps. Apply metal drip edges on top
of any underlay along rake edges and directly to the deck along eaves in accordance with building code
requirements.
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least 3/8" diameter heads, long
enough to penetrate through plywood or 3/4" into boards. Use 4 nails per shingle placed in the nail line 7-3/8"
below the top edge, approx. 1" and 13" in from each end. Drive nails straight so that nail head is flush with,
but not cutting into shingle surface.
NAILING ON STEEP SLOPES: For steep slopes of 21" per foot (60°) or more, use 6 nails per shingle placed
as shown below. Ensure that no nail is within 2" of a joint/cutout of the underlying shingle. Seal down each
shingle at time of application with three 1" diameter (approx. size and thickness of a quarter) spots of asphalt
plastic cement placed under the shingle 2" above the bottom edge and equally spaced along the shingle.
Apply plastic cement in moderation since excessive amounts may cause blistering. CAUTION: Shingles
should seal to the underlying course when the factory applied asphalt sealant is sufficiently warmed by the
heat of direct sunlight.
EXPOSURE: Installed shingles shall have a maximum average exposure of 5-7/8".
6 3J
NAIL LINE
NAILING - STEEP SLOPES APPLICATION
Use sic nails as shown.
Fa EL F1 -,Tl
CEMENT
PROPER APPLICATION REQUIRES THAT THE NAILS PENETRATE BOTH THE OVERLAY AND UNDERLAY PORTIONS OFTHE SHINGLE
PRI Construction Materials Technologies, U.C. 6412 Badger Drive Tampa, FL33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: materialstesting@pricmt.com WebSite: http://www.pricmLcom
IKO
Installation Instructions for
Asphalt Shingles
Page 4 of 5
IKO Hip and Ridge 12 Application Instructions
ASTM D3161, Class F — IKO Hip and Ridge 12)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
Cut hip and ridge shingles into thirds, using the perforation marks as a cutting guide. These shingles are
designed for a 5 1/8" (130 mm) exposure. (For a neater appearance, the top of each side of each piece has
been factorytrimmed on a 1" (25 mm) taper (see drawing). Bend each piece over the hip or ridge, and nail 5 5/
8" (143 mm) above the butt edge 1" (25 mm) in from each edge, exposing each piece 5 1/8" (130 mm). Apply
hip pieces starting at the lower end of the hip, working up toward the ridge. On hip roofs, apply ridge pieces
starting at each end, meeting in the middle. On gable roofs, apply ridge pieces starting at the end opposite
to the prevailing wind direction and continue to the other end. Note: To obtain a three-dimensional effect, (
which is recommended, but not required), apply hip and ridge shingles double thickness by stacking 2 pieces
on top of one another, the lower piece extending about 3/4" (19 mm) further than the top piece (see diagram).
The final shingle should be set in cement, and the exposed nail heads of the final shingle should be covered
with cement. Prior to application in cold weather, storing the shingles in a heated area will allow for easier
bending. NOTE:
SHINGLES MUST BE APPLIED PROPERLY. THEY ARE DESIGNED FOR USE AS HIP AND RIDGE SHINGLES
ONLY, AND SHOULD NOT BE USED FOR ANY OTHER APPLICATIONS. WE ASSUME NO RESPONSIBILITY
FOR LEAKS OR DEFECTS RESULTING FROM POOR APPLICATION OR FAILURE TO PROPERLY
PREPARE THE SURFACE TO BE ROOFED OVER, OR FAILURE TO PROVIDE PROPER VENTILATION
IN ACCORDANCE WITH MINIMUM PROPERTY STANDARDS REQUIREMENTS. REVIEW ALL
APPLICABLE BUILDING CODES, MINIMUM PROPERTY STANDARDS, AND REQUIREMENTS PRIOR TO
APPLYING THESE SHINGLES USING THESE APPLICATION INSTRUCTIONS. TAPER
CUT PRI
Construction Materials Technologies, LLC. 6412 Badger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: matedalstesting@pdcmt.com WebSite: http://www.pricmtcom
IKO
Installation Instructions for
Asphalt Shingles
Page 5 of 5
IKO Leading Edge Plus Application Instructions
ASTM D3161, Class F — IKO Leading Edge Plus)
NOTE: THESE INSTRUCTIONS SHALL BE USED IN CONJUCTION WITH IKO'S PUBLISHED
APPLICATION INSTRUCTIONS AND THE APPLICABLE CODE. IN THE EVENT THE INSTRUCTION
CONFLICT, THESE INSTRUCTIONS WILL GOVERN.
1. Apply any underlayment, eave protection, valley flashings, or drip edges to roof deck as required.
2. Each 39 3/8" x 131/4" (1000 mm x 336 mm) IKO Leading Edge Plus strip is perforated lengthwise for
separation into two (2) shingles. Take one IKO Leading Edge Plus strip and fold flat at perforation to
separate.
3. Take one of the separated shingles 39 3/8" x 6 5/8" (1000 mm x 168 mm) and remove approximately
20"(500 mm). Install this shingle on the lower left comer of the roof deck, granule side up, with the
factory installed sealant adjacent to the eaves. The shingle should overhang the rake edge and eaves
by a nominal 1/4" (6 mm) minimum. Fasten the shingle to the roof deck with nails located 3" to 4" (75
mm to 100 mm) from the eave edge and 1" (25 mm) in from each end.
4. Take the leftover 20" (500 mm) piece shingle. Rotate the piece and align it vertically up the rake edge
with the factory installed sealant adjacent to the outer edge of the roof. The shingle should overhang
the rake edge by a nominal 1/4" (6 mm) minimum. Fasten the shingle to the roof deck with fasteners
located 3" to 4" (75 mm to 100 mm) from the rake edge and 1" (25 mm) in from each end.
5. Repeat Steps 3 —4 for the right lower corner of the roof deck.
NAILING: Use galvanized (zinc coated) roofing nails, 11 or 12 gauge, with at least
3/8" (9 mm) diameter heads, long enough to penetrate through plywood or 3/4" (20
mm) into boards. Use 4 nails per shingle placed 3" to 4" (75 mm to 100 mm) from
the eave edge and approximately 1" and 13" (25 mm and 330 mm) in from each end.
6. Apply full-length IKO Leading Edge Plus shingles to the remaining eave edges of the roof deck. Install
the shingles granule side up with the factory applied sealant adjacent to the eaves. The shingles
should overhang the rake edge and eaves by a nominal 1/4" (6 mm) minimum. Fasten the shingles to
the roof deck with nails located 3" to 4" (75 mm to 100 mm) from the eave edge, 4 nails per shingle.
7. Apply roof shingles as per the instructions printed on each product's package. Make certain the first
course of field shingle lies flush with the edges of the fastened IKO Leading Edge Plus. In this way,
the sealant on the IKO Leading Edge Plus shingles will adhere to the first -course field shingles and
help keep them from lifting in high winds.
PRI Construction Materials Technologies, LLC. 6412 Badger Drive Tampa, FL 33610 Tel: 813.621-5777 Fax: 813-621-5840 e-mail: materialstestng@pricmt.com WebSite: http:/lwww.pricmtcom
LIMITED POWER OF ATTORNEY
Altamonte Springs, Casselberry, Lake Mary, Longwood, Sanford,
Seminole County, Winter Springs
Date: 11- -1 6
I hereby name and appoint: A5V) le q 6 6s
an agent o£ Oak Crest Contracting
Name of Company)
to be my lawful attorney -in -fact to act for me to apply for, receipt for, sign for and do all things
necessary to this appointment for (check only one option):
S( The specific permit and application for work located at:
136 V OSoo OjaU C• -
Street Address)
Expiration Date for This Limited Power ofAttorney:
License Holder Name: Dustin Doll
State License Number:
Signature of License H
STATE OF FLORIDA
COUNTY OF " 1%V-Cke
The foregoi strument was acknowledged before me this
l
1 5 da of,
20 , by t N (tit,, who isersonally known
to me or o who has produced as
identification and who did (did not) t< n ath.
Signature
Notary Sear G, RYLJ y
GO'i • Print or type name
N
QG 229700
r Z- REB = Notary Public -State of i
a '•, Commission No. CO
gd' u u '.• My Commission Expires: (o- f • o?oz
Rev. 08.12)
CITY OF ,
ORD Building & Fire Prevention Division
RESIDENTL4L RE -ROOF POLICY & PROCEDURES
FIRE DEPARTMENTMENT 3j
PERMITTING REQUIREMENTS - NO PLAN REVIEW REQUIRED
THIS DOCUMENT (SIGNED) ALONG WITH AN ACCURATE AND COMPLETED RESIDENTIAL RE -ROOF SCOPE OF WORK ARE
REQUIRED TO BE SUBMITTED AS PART OF YOUR PERMIT APPLICATION.
THE SCOPE OF WORK MUST INCLUDE ALL APPLICABLE FLORIDA PRODUCT APPROVAL NUMBERS FOR ALL ROOF
COMPONENTS THAT WILL BE INSTALLED ON THE PROJECT.
A PERMIT WILL NOT BE ISSUED WITHOUT THESE DOCUMENTS. COPIES WILL BE MADE TO POST ON THE JOB SITE.
PROJECTS LOCATED IN THE SANFORD HISTORIC DISTRICT WILL REQUIRE PLAN REVIEW AND APPROVAL BY THE
SANFORD HISTORIC PRESERVATION BOARD
INSPECTION POLICY & PROCEDURES
A FINAL ROOF INSPECTION IS THE ONLY INSPECTION REQUIRED FOR RESIDENTIAL (SINGLE FAMILY, TOWNHOUSE,
MOBILE HOME, APARTMENT AND/OR CONDOMINIUM) RE -ROOF PERMITS.
THE FOLLOWING IS REQUIRED TO BE PROVIDE ON THE JOB SITE:
PERMIT CARD, POSTED IN A CONSPICUOUS AND WEATHERPROOF LOCATION
COMPLETED RESIDENTIAL RE -ROOF SCOPE OF WORK
COMPLETED AND NOTARIZED INSPECTION AFFIDAVIT
ALL FLORIDA PRODUCT APPROVAL AND CORRESPONDING INSTALLATION INSTRUCTIONS
PRODUCT APPROVAL SHALL MATCH WHAT IS ON THE SCOPE OF WORK)
DIGITAL PHOTOGRAPHS (MUST INCLUDE THE PERMIT NUMBER OR ADDRESS IN EACH PICTURE)
o EACH PLANE OF THE ROOF, SHOWING THE UNDERLAYMENT INSTALLED
o ROOF DECK NAILING PATTERN & SPACING (INCLUDING A MEASURING DEVICE OR RULER)
o ROOF DECK NAILS USED (INCLUDING A MEASURING DEVICE OR RULER SHOWING SIZE OF NAILS)
o UNDERLAYMENT PATTERN & SPACING (INCLUDING A MEASURING DEVICE OR RULER)
o DRIP EDGE & VALLEY ATTACHMENT (INCLUDING A MEASURING DEVICE OR RULER)
o SHINGLES INSTALLED, NAIL PATTERN AND LOCATION OF NAILS
SKYLIGHTS (IF APPLICABLE)
o DIGITAL PHOTOGRAPHS SHOWING ALL INSTALLATION COMPONENTS, PER FL PRODUCT APPROVAL
o DIGITAL PHOTOGRAPHS SHOWING ALL REQUIRED FLASHING, PER FL PRODUCT APPROVAL
FAILURE TO FOLLOW THESE SPECIFIC GUIDELINES WILL RESULT IN AN AFFIDAVIT PROVIDED BY A FLORIDA DESIGN
PROFESSIONAL (ARCHITECT OR ENGINEER), CERTIFYING FBC CODE COMPLIANCE BY PERSONAL INSPECTION.
CONTRACTOR (OR OWNER/BUILDER) SIGNATURE: I DATE: 11 /14/18
CITY OF
ORD! PERMIT #
i
Building & Fire Prevention Division
FIRE DEPA RTMEN-r RESIDENTML RE -ROOF SCOPE OF WORK
JOB ADDRESS: 136 Wilson Bay Ct
STRUCTURE TYPE: (D SINGLE FAMILY RESIDENCE/TOWNHOUSE O MOBILE HOME O APARTMENT/CONDOMINIUM
RE -ROOF TYPE: 0 REPLACEMENT (TEAR OFF EXISTING ROOF AND REPLACE WITH NEW COMPONENTS)
O RE-COVER (NEW ROOF INSTALLED OVER EXISTING ROOF)
DECK TYPE (PLEASE SPECIFY):
PLEASE NOTE. ONLY 100 SQUARE FEET OF THE EXISTING DECK IS PERMITTED TO BE REPLACED**
ROOF VENTILATION: * OFF -RIDGE O RIDGE OSOFFIT OPOWERED VENT OTURBINES
SKYLIGHTS: O YES * NO IF YES, PLEASE PROVIDE FLORIDA PRODUCT APPROVAL #:
MAIN ROOF AREA
ROOF SLOPE: O LESS THAN 2:12 O 2:12-4:12 * 4:12 OR GREATER
TYPE OF ROOF MANUFACTURER FLORIDA PRODUCT APPROVAL
SHINGLE IKO Cambridge FL# FL7006.1
O METAL FL#
O MODIFIED BITUMEN FL#
O TORCH DOWN FL#
OINSULATED FL#
O TILE FL#
O OTHER: FL#
ROOF EXTENSIONS (PORCHES, PATIOS, ETC.) **IFAPPL/CABLE**
ROOF SLOPE: O LESS THAN 2:12 O 2:12 - 4:12 O 4:12 OR GREATER
TYPE OF ROOF MANUFACTURER FLORIDA PRODUCT APPROVAL
O SHINGLE FL#
O METAL FL#
O MODIFIED BITUMEN FL#
O TORCH DOWN FL#
OINSULATED FL#
O TILE FL#
O OTHER: FL#
r
CITY OF'
ORD Building & Fire Prevention Division
RESIDENTIAL RE-ROOFAFFIDAVIT
FIRE Dl i'ARTMENT
RESIDENTIAL RE -ROOF INSPECTION AFFIDAVIT
NAILING, SHEATHING, DRY -IN, FLASHING, AND ALL FINAL ROOF COVERINGS
PERMIT #: 16 — 4I55 U ADDRESS: 136 Wilson Bay Ct
Sanford, FL 32771
I Dustin Doll , AS A(N) GENERAL, BUILDING, RESIDENTIAL, OR
ROOFING CONTRACTOR, ENGINEER, ARCHITECT, OF F.S. CHAPTER 468 BUILDING INSPECTOR, I HEREBY AFFIRM, THAT ALL OF THE
FOREGOING INFORMATION IS TRUE AND ACCURATE AND THAT ALL ROOFING COMPONENTS LISTED ON THE SCOPE OF WORK AT THE
ABOVE REFERENCED ADDRESS HAVE BEEN INSTALLED IN ACCORDANCE WITH THEIR PRODUCT APPROVALS AND ALL APPLICABLE CODE
REQUIREMENTS - SPECIFICALLY FLORIDA BUILDING CODE, EXISTING BUILDING. IN ADDITION I CERTIFY THE INSTALLATION MEETS ALL
REQUIREMENTS FOR SECONDARY WATER BARRIER AND NAILING OF THE ROOF DECK, IN ACCORDANCE WITH THE HURRICANE RETROFIT
MANUAL REQUIREMENTS (BASED ON F.S. CHAPTER 553.844).
LICENSE#: CCC1330407
COMPANY / CONTRACTOR:
Q ( CONTRACTOR SIGNATURE: DATE:
MUST BE SIGNED BY LICENZH ROR O R/BUILDER)
A FINAL ROOF INSPECTION LS REQUIRED:
THIS SIGNED AND NOTARIZED AFFIDAVIT MUST BE PROVIDED AT THE JOB SITE AT THE TIME OF THE FINAL ROOF INSPECTION,
ALONG WITH DIGITAL PHOTOGRAPHS OF EACH PLANE OF THE ROOF SHOWING IN DETAIL ALL COMPONENTS (DECKING,
UNDERLAYMENT, FLASHING, DRIP EDGE ATTACHMENT) WITH THE PERMIT NUMBER OR ADDRESS CLEARLY MARKED ON THE DECK
FOR EACH INSPECTION. THE PHOTOGRAPHS MUST INCLUDE A RULER OR MEASURING DEVICE TO CONFIRM ALL NAIL SPACING AND
OVERLAPS, INCLUDING DRIP EDGE AND VALLEY FLASHING. PLEASE REFER TO THE RE -ROOF POLICY AND INSPECTION PROCEDURE
PAPERWORK FOR FURTHER EXPLANATION OF ALL REQUIREMENTS.
FAILURE TO FOLLOW ALL REQUIREMENTS WILL RESULT IN A FAILED INSPECTION, A RE -INSPECTION FEE AS
WELL AS REQUIRING A DESIGN PROFESSIONAL (ARCHITECT OR ENGINEER) TO CERTIFY, BASED ON PERSONAL
INSPECTION, THE INSTALLATION OF ALL ROOFING COMPONENTS.
STATE OF FLORIDA COUNTY OF rn i n C) ( P.
Sworn to and Subscribed before me this 19 day of Nov enmhr- 20 L by: Do'
l n S*OI L . Who is Personally Known to me or has Produced (type of identification) —
Signature
of N4 y Public State
of Florida I'
Tohlcy &6 S Print/
Type/Staimp Name of
Notary Public as
identification. Ashley
GOIS piSSI4N
G 29759 EXPIRES:
Jug 19, 2022