166 Towne Center Cir - BC07-002561 (FREDERICKS OF HOLLYWOOD) (INTERIOR REMODEL) DOCUMENTSPERMIT ADDRESS
vAr
ADDRESS
rE
ud
PHONE NUMBER I t 1- 146 o A141
fmftsa ,
PROPERTY OWNER rDel s
ADDRESS
PHONE NUMBER
ELECTRICAL CONTRACTOR
MECHANICAL CONTRACTO
PLUMBING CONTRACTOR
ire.
MISCELLANEOUS CONTRACTOR
PERMIT NUMBER FEE
MISCELLANEOUS CONTRACTOR
PERMIT NUMBER FEE
SUBDIVISION
PERMIT # 01 a6& I DATE
PERMIT DESCRIPTIONI Aa&j AALL
PERMIT VALUATION OQ 00
SQUARE FOOTAGE
Y
C7
C7
cn
cn
t
O
d
a
to
O
CITY OF SANFORD PERMIT APPLICATION
Permit # : o % - 2.r ( I Date: 4 0
Job AddreAU71te 2169 TO VV%e C-GN+,W C.O UGkL S A^ 4'94A
i
F I. 3.17 % I
Description of Work: S w t IWO/ 4WA 4ft— Total Square Footage
Historic District: Zoning: Value of Work: $ 6J rev -oJ
Permit Type: Building Electrical I/ Mechanical Plumbing Fire Sprinkler/Alarm Pool
Electrical: New Service - # of AMPS Addition/AIteration J/ Change of Service Temporary Pole
Mechanical: Residential Non -Residential Replacement New (Duct Layout & Energy Calc. Required)
Plumbing/ New Commercial: # of Fixtures # of Water & Sewer Lines # of Gas Lines
Plumbing/New Residential: # of Water Closets Plumbing Repair- Residential or Commercial
Occupancy Type: Residential Commercial Industrial _
Construction Type: ! # of Stories: # of Dwelling Units: _ Flood Zone: (FEMA form required )
OwnersName & Address: S f IMt h PI/0 ptl+/ +"ti 0 • ao j( 1033
Ide LNw Phone: 3
Contractor Name & Address: Terns AAC K i o mon Lowry 14A, K A-QWr`i EIefo t'C Tyt
C. S—Lf 0V 1 _ State License Number: h C, I i DO 3 i I I Phone &
Fax: µ01 ` g s t • O i% Contact Person: _ 614M iL-lwe lh Phone: 40-7 - 6r z - idrr Bonding
Company: A-11114 Address:
Mortgage
Lender: Address:
Architect/
Engineer: nft k It Phone: Address: l%
1% Fax: Application is
hereby made to obtain a permit to do the work and installations as indicat•:d. 1 certify that no work or installation has commenced prior to the issuance of
a permit and that all work will be performed to meet standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must
be secured for ELECTRICAL_ WORK, PLUMBING, SIGNS, WELLS, POOLS, FURNACES, BOILERS, FIEATERS, TANKS, and AIR CONDITIONERS,
etc. OWNER'S
AFFIDAVIT: I certify that all ofthe foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating construction and
zoning. WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESUL f IN YOUR PAYING TWICE FOR
IMPROVEMENTS TO YOUR PROPERTY. 11' YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE
RECORDING YOUR NOTICE OF COMMENCEMENT. NOTICE: In
addition to the requirements of this permit, there may be additional restrictions applicable to this property that may be found in the public records of this county,
and there may be additional permits required from other governmental entities such as • manageme stricts, state agencies, or federal agencies. Acceptance of
permit is verification that 1 will notify the owner of the property of the requ' ement Florida Lien Law S 713. 9V17 Signature
of
Owner/Agent Date Signature of Contractor/Agent Date T.,f !
w„ Print Owner/
Agent's Name Print uractot/Agent's Marne Signature of
Notary -State of Florida Date Signature of Notary -State of Florid Date IVELISSE 10TINEZ
Notary Public, St
a of Florida My Comm. Expires
Jan. 19, 2010 No. DD 08831
Owner/Agent is _
Personally Known to Me or Contractor/Agent is _ Personally Known to Me or Produced ID _ Produced
ID APPROVALS: ZONING: Special
Conditions: Rev
03/2006
UTIL: FD: L"•
NG BLDG:
POWER OF ATTORNEY
Date: C//S15DO%
I hereby name appoint,l12/2QV GRIFFIN of 926Uk Q WZV i-&C-. to
L"v
Be my lawful attorney in fact to act for me and apply to the 1T,,ij Z
Building Department for a/an kIjgc 72 i A:4 - permit
For work to be performed at a location described as: a o 0 T0 LvA a Cery raz C i QCLr= 54e l F-ozv =t- .'SL-)'11
Section Township Range Lot Block
SIM 0/1 P aP1ave-1-7is
Subdivision PO 90V- 70A I1h I /fVn 0J1-1 n,i MTV j 1,4/1A HbLOI
Owner of Property and Address)
and to sign my name and do all things necessary to this appointment.
112e rj r ivl G Kl Aap Louay I= G I3oo 3. 1 1
Type or priii ame of Re&yzter qr Certified Cont actor and Contractor's License Number
Signature of Reloter or Certified Contractor
The foregoing instrument was acknowledged before me this S `day of 2007
By:
Who ' ersonallyown to me /who produced
As identification and w o did t take oath.
State of Florida
County of
IVELISSE MARTINE7_
Notary Public, State of Florida
My Comm. Expires Jan. 19. Zptq
No. DD50883 1
Notary Public, Orange CoupIy, Florida
DATE:
CITY OF SANFORD ]FIRE DEPARTMENT
FEES FOR SERVICES
PHONE # 407-302-2516 - FAX # 407-302-2526
PERMIT #:
BUSINESS NAME / PROJECT:
ADDRESS: !(.a(o C-i-2
PHONE NO.: 4o7- 235- //3E: FAX T+O.: go-)— zzs ii,570
CONST. INSP. [ ] C / O INSP.:(] REINSPECTION [ ) . PLANS REVIE
F. A. [ ] F.S. [ ] HOOD [ ] PAINT BOOTH [) BURN PtRNGT [ )
TENT PERMIT ] TANK PERMIT [ ] OTHER [ ]
TOTAL FEES: S (PER UNIT SEE BELOW)
COMMENTS:
Address / Bldg. # / Unit # Square Footage
2.
3.
4.
5.
6.
7.
8.
9.
10.
12.
13. --
14.
15.
16.
17.
18.
19.
20.
Fees per Bldg. / Unit
Fees must be paid to Sanford Building Department. 300 N. Park Ave., Sanford, FI. 32771 Phone # -407-
330-5656. Proof of Payment must be made to Fire Prevention division before any further services can take
place. I certify that the above is true and correct and that I
will comply with all applicable codes and ordinances
ol'the City of Sanford. Florida.
Sanford F' Preve tion Division Applicant's Signature
CITY OF SANFORD 1FIRE DEPARTMENT
FEES FOR ,SERVICES
PHONE # 407-302-2516 - FAX # 407-302-2526
DATE:/-7
J
PERMIT #:
BUSINESS NAME / PROJECT: rt? C Q.,,
ADDRESS: C,k('G
PHONE N 6FAX NO.:
CONST. INSP. [ J C 10 INSP.:[ J REINSPECTION [ ] PLANS REVIEWF. A. (] F.S. [ J HOOD [ J PAINT BOOTH ( BURN PE MIT [
TENT PERMIT E ] TANK PERMIT [ ] OTHER ( .S
TOTAL FEES: S 31- 3 (PER UNIT SEE BELOW) ` '
COMMENTS: y r nn,co -—, (r'Zr2_
Address / Bldg. # / Unit # Square Footage Fees per Bldg. / Unit
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
002,j
Fees must be paid to Sanford Building Department, 300 N. Park Ave., Sanford, FI. 32771 Phone # -407-
330-5656. Proof of Payment must be made to Fire Prev;ntion division before any further services can take
place. I certify that the above is true and correct and that I
will comply with all applicable codes and ordinances
of the City of Sanford, Florida.
ll/ t'Vl0
Sanford Fire Pre ve ion Division Applicant's Signature
1
CITY OF SANFORD PERMIT APPLICATION Fre.dgl Js
Application # _ _ Submittal Date:
Job Address: `- .. E, ^ ,,..
e , ; (,'
Yea L Value of Work $ 1 O
Parcel ID: 8 ="
4` `"
g.i``. Zoning. Historic District: v
Description of Work: I r i-Y z gi Square Footage: /
Permit Type: Building Electrical Mechanical Plumbing Fire Sprinkler/Alarm Pool Sign
Electrical: New Service - # of AMPS :-
7 `
Addition/Alteration Change of Service Temporary Pole
Mechanical: Residential Non -Residential Replacement
Plumbing/ New Commercial: # of Fixtures 3 # of Water & Sewer Lines
Plumbing/New Residential: # of Water Closets
Occupancy Type: Residential Commercial's Industrial
New A(Duct Layout & Energy Calc. Required)
of Gas Lines
Plumbing Repair -Residential 01 Commercial
Occupancy Use Group(s):
Construction Type: _ # of Stories: # of Dwelling Units: A Flood Zone: (FEMA form required)
Property Owner: S4 M1f?A) {% lam? ( Contractor "€ `Lc, Y*€ r_
Address: 0 Address { a
i'°'• i x. e'•, P' r' r'" _ £ i `;T : :^r ' C? '" --"' ,t,a t t' '. %-'i ' ` —
Phone. E-mail: ' # Phone: 7- I ( State License Number:
Bonding Company`. ? •i` Mortgage Lender:
Address
Architect/Engineer:
Address: 9
Address:
Phone. 0 l -2,0 - (0
Fax f tj -' 'q I - ICE7 t>
Plan Review Contact Person: (0 0 Phone: 1 i => ( ? Fax
Application is hereby made to obtain a'permit to do the work and installations as indicated I certify that no work or installation has commenced prior to the
issuance of a -permit and that all work will be performed to meet standards of all laws regulating constriction in this jurisdiction. I understand thata separate
permit must be secured for ELECTRICAL WORE, PLUMBING, SIGNS, WELLS, POOLS, FURNACES. BOILERS, HEATERS. TANKS, and
AIR CONDITIONERS. etc.
OWNER'S AFFIDAVIT: I certify that all of the lbregoing information is accurate and that all work will be done in compliance with all applicable laws regulating
construction and zoning.
WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR
IMPROVEMENTS TO YOUR PROPERTY. A NOTICE OF COMMENCEMENT MUST BE RECORDIiD AND POSTED ON THE JOB SITE BEFORE THE
FIRST" INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR
NOTICE OF COMMENCEMENT.
NOTICE: In addition to the requirements of this permit, there may be additional restrictions applicable to this property tlw may be found in the public records of
this county, and there may be additional permits requiredfrom other governmental entities such as water management districts, state agencies, or federal agencies.. Acceptance
of per is veritin that 1 w"Il n rtifj t1je ownert Ux pwR e0yLF6Signature
of"Owner/Agent Date n7 Xr `Sign; I)
0 v Print
Owner/Agent's Name Print Sig
Date Si fflVftk-=`
OFliORIDA Patrick C.
Halpenny Commission # DD472356
Expires: NOV.
03, 2009 0,,%PAO
jWu AtlaM lPt jkl&Cl4rxt1, M, or Produced ID ,=
co124rGr1 0R4A4.-5 A APPROVALS:
ZONING:
Special Conditions:
Rev 07.
07 UTIL: FD.-
Lien Law.
FS 713. ractor/Agent
Date n $ $ ..i-
ram Name Date
A
MELISSA
R STAi Y y r
VtY COMMISSIC)N $ Ctp599223 ja OF
Q4L° E-XPIRFS: Sept. 26, 2010 407) 398'
01 S3 irioldti NOWY: Senivacom . c'f
C"or"%4gentis Personally Known to Me or Produced ID
Lo. ENG:
BLDG:
9 .
0- /,,
CITY OF SANFORD PERMIT APPLICATION
Application # : d Submittal Date:
p
Job Addr' 7t f v Y1 CP t7 -iyn c,4-4,
t
ST `V
Value of Work:
Parcel ID: 1(A^ L 11'' o '- DOt Zoning: Historic District: No
Description of Work: re rn b de_( ,u t f—C 1 Y' Se r') I t) tC iill Square Footage: ` %` 61 ? 2 U01
Permit Type: BuildingElectrical Mechanical Plumbing Fire Sprinkler/Alarm Pool Sign Electrical:
New Service — # of AMPS d Addition/Alteration 1 Change of Service Temporary Pole Mechanical:
Residential Non -Residential Replacement New (Duct Layout & Energy Cale. Required) Plumbing/
New Commercial: # of Fixtures 2, # of Water & Sewer Lines z # of Gas Lines 0 Plumbing/
New Residential: # of Water Closets Plumbing Repair —Residential Commercial Occupancy
Type: Residential Commercial ` Industrial Occupancy Use Group(s): M Construction
Type: # of Stories: _(_ # of Dwelling Units: _ Flood Zone: (FEMA form required I C '
n r cfI"r r PropertyOwner: •,'1 %1'1(") N , d ty'1/Contractor: r. F'( ? r- ".1 r Address:
P r? I c r % 0 5 %i Address: 204,
Phone:
E-mail: ^ (Phone: Zt I SY i`I( State License Number: CC 0 1 1 Bonding
Company: m / A Mortgage Lender: /y/gV) Address
Address: Architect/
Engineer: T—
tPhone:
2q-7 — (0 Ulett `..Z ChAddress: 10—
0 VLK A t , G Ay-e j0y--C . C-0 It/ W. >>S 1 U ri' 1'f -' L U 1 Fax: (d 1-(- ZQ 1 — Plan Review Contact
Person: k( bt i E' 1—UL . ;A Phon:( i'; U Fax a Sv `: ^L E-
mail: r'U'iJ{`
if i U.'r'! i%Ln!Yi i, t.t G,;v, Application is hereby
made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the issuance of a
permit and that all work will be performed to meet standards of all laws regulating construction in this jurisdiction. I understand that a separate permit must be
secured for ELECTRICAL WORK, PLUMBING, SIGNS, WELLS. POOLS, FURNACES, BOILERS, HEATERS, TANKS, and AIR CONDITIONERS, etc.
OWNER'S AFFIDAVIT:
I certify that all of the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating - construction and zoning.
WARNING TO OWNER:
YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS TO YOUR
PROPERTY. A NOTICE OF COMMENCEMENT MUST DE RECORDED AND POSTED ON THE 10B SITE BEFORE THE FIRST INSPECTION. IF
YOU INTEND TO OBTAIN FINANCING, CONSULT WITH YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT.
NOTICE: In addition
to the requirements of•this permit, there may be additional restrictions applicable to this property L-lorida und
inthe
public records of this county, and
there may he additional permits required from other governmental entities such as water management dgencies, or federal agencies. Acceptance of'permit
is verification that I will notify the ownergf-tlxr ert fill requirementsn Law, FS 713, _Co!) Signature of
Owner/
Agent Date ;ignatureofC itractor/AgenDate t 74 Print Owner/Agent'
s
Name Print Contractor/Agent's Name C Signature of Notary -State
of Florida Date Si et "" Date 1P 0 e MELISSA
K STA Y i`N t MY
COMMISSION #
DD599223
OFr e EXPIRES: Sept.
26.
2010 407) 398-0153 FlOtlda
Notety Sorviae.aom Owner/Agent is _ Personally
Known to Me or Co r, c or Agent is Personally Known to Me or Produced ID _ Produced ID
1 APPROVALS: ZONING: UTIL: ENG:
BL Special Conditions: IIW4Rev 07.
07 Iq
Application H : a7::A l0 1
r
Job Address:
Parcel ID:
CITY OF SANFORD PERMIT APPLICATION
aSubmittalDatc:
Value of Work: S
Zoning: _ historic District:
Description of Work: drL y Square Footage:
i.............i...................................................................... Permit hype: Building Electrical Mechanical Plumbing Fire Sprinkler/Alarm Pool Cl Sign
Electrical: New Service -„ ol*:\\Ill's l(lition/:\Iteration Change of Service Temporary Pole
Mechanical: Residential Nun -Residential Replacement New (Duct L.avout & Energy Calc. Required)
Plumbing/ New Commercial: 4 of l-ixnrres •'r of %Vater &, Scwcr L.incs it of Gas Lines _
Plurnbing/New Residential: tl of Water Closets Plumbing Repair - Residential Commercial
Occupancy Type: Residential Commercial 0- Industrial Occupancy Use Group(s):
Construction Type: b of Stories: _ 9of Dwelling Units: _— Flood "Gone
1................
Property Owner: - '
f '
f v(
J
Contractor:
Ad ss: Addr
r
Phone: E-mail:e1
Bonding Company:
Address:
Architect/Engineer:
Address:
Plan Review Contact Person:
FF.MA form required
State License Number40/62g2;!-—?-J Z3
Mortgage Lender:
Address:
Phone:
Fax:
Phone: Fax: E-mail:
Application is hereby made to obtain a permit to do the work and installations as indicated. I certify that no work or installation has commenced prior to the
issuance of a permit and that all work will be pertorrned to meet standards of all laws regulating construction in this jurisdiction. I understand that a separate
permit must be secured for ELECTRICAL WORK, PLUMBING, SIGNS, WI3LI. S, POOLS. FURNACES, BOILERS, HEATERS. TANKS, and
AIR CONDITIONERS, etc.
OWNER'S AFFIDAVIT: I certify that all of the foregoing information is accurate and that all work will be done in compliance with all applicable laws regulating
construction and zoning.
WARNING TO OWNER: YOUR FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR I'AYING TWICE FOR
IMPROVEMENTS TO YOUR PROPERTY. A NOTICE 01: COMMENCEMENT MUST BE RECORDED AND POSTED ON THE J013 SITE BEFORI: THE
FIRST INSPECTION. IF YOU INTEND TO OBTAIN FINANCING, CONSUur Wrm YOUR LENDER OR AN ATTORNEY BEFORE RECORDING YOUR
NOTICE OF COMMENCEMENT.
NOTICE: In addition to the requirements of this permit, there may be additional restrictions .applicable to this property that may be found in the public records of
this county, and there may be additional permits required from other governmental entities such as water management districts, state agencies, or federal agencies.
Acceptance of permit is verification that I will notil'y the owner of(
Signature of OwnedAgent Date
Print Owncr/Agent's Name
Signature of Notary -State of Florida Date
Owner/Agent is _ Personally Known to Me or
Produced ID
APPROVALS: ZONING:
Special Conditions:
Rev 07.07
U'I'1 L,: FD:
3.
13- D
Contractor/Aginti nall ' `' . I' • soy Kiios c D1c or
ProduC16
Cd/-rryi
ENG/\ 13LDG:------ -- -
CITY OF SANFORD PERMIT APPLICATION
Application q : O 1,Q- -
r `
Job Address: t0(9 - W e { r r -•- -
Submittal Date
RFORVED
Value of Work: $$ -.1uIl
Parcel ID: -__
1 1
Zoning: Hisioric District: -_
Description of Work: AcVA+ l f• eOdb :;±- -O/ Square rootage: - -
Permit Type: Building Fleetrical Mechanical Plumbing Fire Sprinkler/Alarm Pool Sign
Electrical: New Service - N of AMPS __ Addition/Alteration Change of Service Temporary Pole
Mechanical: Residcnlial Non -Residential Replacement U New (Duct Layout & Encrgy Cale. Required)
Plumbing/ New Commercial: Ii of Fixtures _ _ -- t1 of Water & Sewer Lines,
Plumbing/New Residential: It of Water Closets
Occupancy'rype: Residential Commercial Industrial
ft of Gas Lines
PlumbingRepair-Residential Commercial
Occupancy Use Group(s):
Construction Type: — . N of Stories:.-__- V of Dwelling Units: Flood Zone: (FEMA form required )
I............................................................-------
PropertyOwner: kt Vriecde rijCS O- (-{y(ctW-
s
Contractor: -
Address: n_?(21./ J- -
F 0mail: Plione: - -11 'tate License Numbi er: 2 dqr , 3000)2W3
Bonding Company:
Address:
Architect/Engineer:
Mortgage lender:
Address:
Phone:
Address----
L --- -- ----_ ____.-.__
Fax:-- -------- ------
flan Review Contact Person: Un Phone: Fax: F,-mail:.Q1d ALQ/M1 Application
is hereby made to obtain a pennit to do the work and installations as indi,;atcd. I certify that no work or installation has commenced prior to the issuance
of a permit and that all work will be performed to meet standards of all lows regulating construction in this jurisdiction. I understand dial a separate permit
must be scented for IELECI'RICAL WORK, PLUMBING, SIGNS, WELLS, POOLS, FURNACES, BOILERS, IWA'FERS,'I'ANKS, and AIR
CONDITIONERS, ctc. QWNIcR;$
FFIDAVI f: 1 certify that all of the foregoing infomration is accurate and that all work will be done in compliance with all applicable laws regulating conswc6on :
utd zoning. WARNING '
1'0 OWNER: YOUR FAILURE TO RECORD A NOTICE 01: COMM E•NCEMENT MAY RESULT IN YOUR PAYING TWICE FOR IMPROVEMENTS
TU Yout PROPERTY. A NOTICE UP C'OMMENCI:MEN'I' MUST BE R ECORI)ED AND POSTED ON THE JOB SITE, BEFORE TI117 FIRST
TI INSPECON. IF You INTENI)'I'O OBTAIN 1.INANCING, CONSUTA' WITII YOUR LENDER OR AN A'I'1'ORNl Y BtiFOKLE RIECORDING YOUR. NO'
l-1C1'_ OI CUMMI-:N(TMEN'1-. In
addition to the requirements of this permit, there may be additional restrictions applicable to this property that may be I'otmd in the puhlic records of this
county, and there may be additional permits required front other govemrnental entities such as water ntanagenrew districts. stnic agencies. or federal agencies. Acceptance
of permit is verification that I will notify ilhc owner of the property of the r unME ' Worrda Lien Law. FS 713. ignosturc
of O.vncr/Agcm------- --- - Date Signature of Contractor/Agent Date Print
Owner/Agent's Name -- Signature
of Notan :State of Florida - Date Owner/
Agent isPersonally Known to Me or Produced -_--- -__•_ Print
Contractor/
Agent's Name . 12 Signature
of -.
of Florida - Date tc UBI•!C-
STATE OF FLORIDA Kauileen M.
Finley Commission # DD584641
Expires: SEP.
24, 2010 Contractor/At),
Qh'ia1sD T}#2UcY'A 901g4C19oUfb1V0ti/1C,4hC. Produced ID --_ - ___-_. _-._------.-..---.
APPROVALS: ZONING: •--•-•--------------
U HL: --- ._......_. - I D: - - -- ---- tiNG Special Conditions:-----------_..---___.------.-.-----__.__;_
Lr'Iw-.-_---_----- Rev 07.
07 off L.
00
LIMITED POWER OF ATTORNEY
Altamonte Springs, Casselberry, Lalke Mary, Longwood, Sanford,
Seminole County, Winter Springs
Date: G/ Z 6/ 0-7
1 hereby name and appoint: J. M 1 e h I rJ 1 1 S d V!
an agent of: "" r ZrGI I C—d rt Sr 1ruc, f ( (' V1 In C .
Name of Company)
to be my lawful attorney -in -fact to act for me to apply for, receipt for, sign for and do all things
necessary to this appointment for (check only one option):
XAll permits and applications submitted by this contractor.
O The specific permit and application for work located at:
street Addres;)
Expiration Date for This Limited Power of Attorney:. 12-/31 07
License Holder Name:
State License Number
Signature of License E
STATE OF FLORIDA
COUNTY O o,
The foregoing instrument was acknowledged before me this`day of ,
2007, by -Ph a 11 ; e a, C; er—W'Q . who is..<pe sonaIIy known
to me or who has produced
identification and who did (did not) take an oath.
k
Signature
Notary Seal)
NOTARY PUBLIC -STATE OF FLORIDA
Sandra McIntosh
Commission #
AUG.30, 2010
Expires: C815BON
3 ,
BONDED THRU ATLAN fLC BONDING CO., INC.
Rcv. 3/27/07)
Ste„ & a tit c .12y7L s k
Print or type name
Notary Public - State of 1'A0_
Commission No. j)PS;W I
My Commission Expires: sS- 30 - 20 /0
as
PROJECT SUMMARY
Short Desc: 0713126
Owner: FREDERICICS OF HOLLYWOOD
Addressl: SEMINOLE TOWNE CENTER
Address2: 200 TOWNE CENTER CIRCLE
Description: FREDERICK'S OF HOLL
City:
State:
Zip:
Type: Retail Class:
Jurisdiction: SANFORD, SEMINOLE COUNTY, FL (691500)
Cond Area: 2277 SF Cond & UnCond Area:
No of Storeys: 1 Area entered from Plans
Permit No: 0 Max Tonnage
OFF20 IF I C E
If different, write in:
PLAN,REVIEWED
CSC FSANFORD 2/
8/2001 EnergyGauge FLA/COM 2004 v3.00 SANFORD
FLORIDA
32771
New
Finished building 2277
SF 2280
SF 0
JUN
2 ) ?sn7
Compliance Summary
Component Design Criteria Result
ENVELOPE PRESCRIPTIVE PASSES
LIGHTING POWER 2,574.0 4,252.5 PASSES
LIGHTING CONTROLS PASSES
EXTERNAL LIGHTING None Entered
HVAC SYSTEM None Entered
PLANT None Entered
WATER HEATING SYSTEMS None Entered
PIPING SYSTEMS None Entered
Met all required compliance from Check List? Yes/No/NA
IMPORTANT NOTE: An input report of this design building must be submitted
along with this Compliance Report.
2/8/2001 EnergyGauge FLA/COM 2004 v3.00 2
CERTIFICATIONS
I hereby certify that the plans and specifications covered by this calculation are in compliance with the
Florida Energy Code
Prepared By: Building Official:
Date: Date:
II I certify that this building is in compliance with the Florida Energy Efficiency Code
Owner Agent: Date:
If Required by Florida law, I hereby certify (") that the system design is in compliance with the FLorida
Energy Efficiency Code
Architect: Reg No:
Electrical Designer: David F. Gonzalez Reg No: 54327
Lighting Designer: Reg No:
Mechanical Designer: David F. Gonzalez Reg No: 54327
Plumbing Designer: David F. Gonzalez Reg No: 54327
Signature is required where Florida Law requires design to be performed by registered design
professionals. Typed names and registration numbers may be used where all relevant information is
contained on signed/sealed plans.
Project: 0713126
Title: FREDERICK'S OF HOLLYWOOD
Type: Retail
WEA File: Orlando.TMY)
Method C: Prescriptive Envelope Compliance
Item Zone Description Design Limit Meet Req.
Glass PrOZo2 Percent glass Max allowed .000 50.000 Yes
Skylights PrOZo2 Percent Skylight Max allowed .000 5.000 Yes
ROOF PrOZo2 Exterior Roof UValue Max allowed .034 0.034 Yes
Meets Prescriptive Envelope Requirements -- PASSES
2/8/2001 EnergyGauge FLA/COM 2004 v3.00 3
External Lighting Compliance
Description Category Allowance Area or Length ELPA CLP
W/Unit) or No. of Units (W) (W)
Sgft or ft)
None
Project: 0713126
Title: FREDERICK'S OF HOLLYWOOD
Type: Retail
WEA File: Orlando.TMY)
Lighting Power Compliance
Space Ashrae Description Area Height No. of Design Effective Allowance
ID (sq.ft) (ft) Spaces W) (W) (W)
Pr0Zo2Spl 25,00' Sales Area 1,836 12.0 1 6382 2454 3,856
PrOZo2Sp2 30,00' Medium/Bulky Material 441 12.0 1 312 120 397
Storage
Design 6694 (W) PASSES
Effective: 2574 (W)
Allowance: 4252.5 (W)
Project: 0713126
Title: FREDERICK'S OF HOLLYWOOD
Type: Retail
WEA File: Orlando.TMY)
Lighting Controls Compliance
Acronym Ashrae Description Area No. of Design Min Compli-
ID (sq.ft) Tasks CP CP ance
PrOZo2Spl ,001 Sales Area 1,836 1 3 1 PASSES
PrOZo2Sp2 -,002 Medium/Bulky Material Storage 441 1 1 1 PASSES
PASSES
2/8/2001 EnergyGauge FLA/COM 2004 v3.00
System Report Compliance
No. of Units
Component Category Capacity Design Eff Design IPLV Comp-
Eff Criteria IPLV Criteria Hance
None
Plant Compliance
Description Installed Size Design Min Design Min Category Comp
No Eff Eff IPLV IPLV Hance
None
Water Heater Compliance
Description Type Category
Design Min Design Max Comp
Eff Eff Loss Loss Hance
None
Piping ;System Compliance
Category Pipe Dia Is Operating Ins Cond Ins Req Ins Compliance
linchesl Runout? Temp [Btu-in/hr Thick linj Thick linj
1171 SF.Fj
None
2/8/2001 EnergyGauge FLA/COM 2004 v3.00
Project: 0713126
Title: FREDERICK'S OF HOLLYWOOD
Type: Retail
WEA File: Orlando.TMY)
Other Required Compliance
Category Section Requirement (write N/A in box if not applicable) Check
Infiltration 406.1 Infiltration Criteria have been met
System 407.1 HVAC Load sizing has been performed
Ventilation 409.1 Ventilation criteria have been met
ADS 410.1 Duct sizing and Design have been performed
T & B 410.1 Testing and Balancing will be performed
Motors 414.1 Motor efficiency criteria have been met
Lighting 415.1 Lighting criteria have been met
O & M 102.1 Operation/maintenance manual will be provided to owner
Roof/Ceil 404.1 R-19 for Roof Deck with supply plenums beneath it
Report 101 Input Report Print -Out from EnergyGauge FlaCom attached?
2/8/2001 EnergyGauge FLA/COM 2004 v3.00 6
EnergyGauge FLAXOM 2004 v3.00
INPUT DATA REPORT
Proiect Information
Project Name: 0713126
Project Title: FREDERICK'S OF HOLLYWOOD
Address: SEMINOLE TOWNE CENTER
200 TOWNE CENTER CIRCLE
State: FLORIDA
Zip: 32771
Owner: FREDERICK'S OF HOLLYWOOD
Orientation: North
Building Type: Retail
Building Classification: New Finished building
No.of Storeys: I
GrossArea: 2277 SF
Zones
No Acronym Description Type Area
S11
Multiplier Total Area
Sl1
1 PrOZo2 Zone 2 CONDITIONED 2277.0 1 2277.0
Spaces
No Acronym Description Type Depth
ftl
Width Height Multi
IN [ftl plier
Total Area
sfJ
Total Volume
1cl1
2/8/2001 EnergyGauge FLA/COM 2004 v3.00 1
In Zone: PrOZo2
I Pr0Zo2SvI ZoOSpI Sales Area 61.20 30.00 12.00 1 1836.0 22032.0
2 PrOZo2Sp2 ZoOSp2 Medium/Bulky Material 24.50 18.00 12.00 1 441.0 5292.0
Storage
Lighting
No Type Category No. of Watts per Power Control Type No.of
Luminaires Luminaire W] Ctrl pts
In Zone: PrOZo2
In Space: Pr0Zo2Sp1
1 Incandescent Task Lighting 12 60 720 Manual On/Off 1
2 Compact Fluorescent General Lighting 17 52 884 Manual On/Off 1
3 Incandescent General Lighting 1 250 250 Manual On/Off 1
4 Recessed Fluorescent Display/Accent fine 19 70 1330 Manual On/Off 1
No vent merchandise
5 Metal Halide Display/Accent fine 2 39 78 Manual On/Off 1
merchandise
6 Incandescent General Lighting 10 60 600 Manual On/Off 1
7 Incandescent Lighting in retail 36 70 2520 Manual On/Off 1
windows
In Space: PrOZo2Sp2
1 Recessed Fluorescent Display/Accent Lighting 3 64 192 Manual On/Off 1
2
No vent
Incandescent General Lighting 2 60 120 Manual On/Off 1
Walls
No Description Type Width H (Effec) Multi Area DirectionConductance Heat Dens. R-Value
Ift] Ift] plier sf] Btufhr. sf. F] Capacity Ilb/cfI [h.sf.F/Btu]
Btu/sf.F]
In Zone:
2/8/2001 EnergyGauge FLA/COM 2004 v3.00
Windows
No Description Type Shaded U SHGC
Btu/hr sf Fj
Vis.Tra W H (Effec) Multi
IN [ftj plier
Total Area
sq
In Zone:
In Wall:
Doors
No Description Type Shaded? Width H (Effec) Multi
ftj [ftj plier
Area
sf]
Cond. Dens. Heat Cap.
Btu/hr. sf. Fj [Ib/cfj [Btu/sf. Fj
R-Value
h.sf.F/Btuj
In Zone:
In Wall:
Roofs
No Description Type Width H (Effec) Multi
ftj IN plier
Area
sf]
Tilt
deg]
Cond. Heat Cap
Btu/hr. SE Fj [Btu/sf. Fj
Dens.
Ib/cfj
R-Value
h.sf.FBtu]
In Zone: PrOZo2
1 ROOF T24R 19b 26.00 102.85 1 2674.0 0.00 0.0339 0.86 5.47 29.5
Skylights
No Description Type U SHGC Vis.Trans
Btu/hr sf Fj
W
IN
H (Effec) Multiplier
IN
Area
S11
Total Area
Sfj
In Zone:
In Roof:
2/8/2001 EnergyGauge FLA/COM 2004 v3.00
Floors
II No Description Type Width H (Effec) Multi Area Cond. Heat Cap. Dens. R-Value IIft] [ft] plier [sf] [Btu/hr. sf. F] [Btu/sf. F] [lb/cf] (h.sf.F/Btu]
IIn Zone:
Systems
No. Of Units
Component Category Capacity Efficiency IPLV
Plant
Equipment Category Size Inst.No Eff. IPLV
Water Heaters
W-Heater Description Capacit3Cap.Unit III? Rt. Efficiency Loss
Ext-Lighting
II Description Category No. of Watts per Area/Len/No. of units Control Type Wattage IILuminairesLuminaire [sf/ft/No] [W]
2/8/2001 EnergyGauge FLA/COM 2004 v3.00 4
No Type
Piping
Operating Insulation
Temperature Conductivity
F] [ Btu-in/h.sf.F]
Fenestration Used
Glass
Name Glass Type No. of SHGC
Conductance
Panes [
Btu/h.sf.F]
Materials Used
V LT
Nomonal pipe Insulation Is Runout?
Diameter Thickness
in] [in]
Mat No Acronym Description
Only R-Value
Used
RValue
h.sf.F/Btu]
Thickness
IN
Conductivity
Btu/h.ft.F]
Density
Ib/cf]
SpecificHeat
Btu/Ib.F]
187 Mat1187 GYP OR PLAS No 0.4533 0.0417 0.0920 50.00 0.2000
BOA RD,1/2 IN
244 Mat1244 PLYWOOD, 1/21N No 0.6318 0.0417 0.0660 34.00 0.2900
82 Mat182 ASPHALT -SHINGLE AND Yes 0.4400
SIDING
El
91 Matl91 BUILDING PAPER, Yes 0.0600
PERMEABLE FELT
407 Mat1407 R-19 Generic Insulation No 19.0000 0.4147 0.0218 0.30 0.2000
414 Mat1414 R-8 generic Insulatrion No 8.0000 0.1746 0.0218 0.30 0.2000
80 Mat180 AIR LAYER, 41N OR Yes 0.9200
MORE, HORIZ. ROOFS
2/8/2001 EnergyGauge FLA/COM 2004 v3.00 5
No Name
Constructs Used
Simple Massless Conductance Heat Capacity
Construct Construct [Btu/h.sfFI [Btu/sfF[
Density RValue
Ib/cfJ [h.sf.F/Btuj
1053 T24R19b No No 0.03 0.86 5.47 29.5
Layer Material Material Thickness Framing
No. IN Factor
1 82 ASPHALT -SHINGLE AND SIDING 0.000
2 91 BUILDING PAPER, PERMEABLE FELT 0.000
3 244 PLYWOOD, 1/21N 0.0417 0.000
4 414 R-8 generic Insulatrion 0.1746 0.000
5 407 R-19 Generic Insulation 0.4147 0.000
6 80 AIR LAYER, 4IN OR MORE, HORIZ. 0.000
ROOFS
7 187 GYP OR PLAS BOARD,1/21N 0.0417 0.000
2/8/2001 EnergyGauge FLA/COM 2004 v3.00 6
11111111111111111111IIIIII1IIIil111III IIIIII111211 uu fuu NOTICE
OF COMMENCEMENT IVFf' MARYANNE
MORSI:, CLERK OF CIRCUIT COURT PERMIT
NO: PARCEL 29-19-36-5LW-0100-0000 JUL 0 5 UH1NOLE COUNTY 9K-
06197 Pq 19411 (1pg) COUNTYOFSEMINOLESTATEOFFLORIDAGERARDI 'O"L' E RK' S # 2007122757 The
UNDERSIGNED hereby gives notice that improvement will be made to certain real property RI:I;I)1?0f'D A6/P-V ?I?l07 0:51410b PM and
in accordance with Chapter 713, FLORIDA STATUTES, the following information is RECORDING FEI,113 10.00 provided
in this Notice of Commencement: RECORDED BY H DeVore LEGAL
DESCRIPTION (Must include either lot, block, subdivision or section, range) 29-
19-36 URTOHED
COPY P"
P nYrvNE MORSE Return original
to: J. Michael Robinson, Gerardi Construction , Inc. CLERK OF C' :'';T 1604 N.
19th Street, Tampa, Florida 33605 W Ir J-15 OWNER / AGENT
INFORMATION NAME: EDDIE
BOWLES. DIR. REAL ESTATE ADDRESS: 6255 SUNSET BLVD, 6TH FLOOR, HOLLYWOOD, CA 90028 NAME 8
ADDRESS OF FEE SIMPLE TITLEHOLDER (If other than owner)_N /A GENERAL DESCRIPTION
OF IMPROVEMENT REMODEL EXISTING
RETAIL SPACE IN SEMINOLE MALL D/ /CONTRACTOR
INFORMATION NAME GERARDI
CONSTRUCTION, INC., 1604 n. 19TH ST., TAMPA, FL 33605 BOND AMOUNTS
N/A NAME & ADDRESS OF SURETY N/A LENDING ORGANIZATION
NA Name: & Address)
Persons within
the State of Florida, designated by owner upon notices or other documents may be served as provided by SECTION 713.13 (1) (a) (7), FLA STATUTES NAME PHILLIP
H. GERARDI ADDRESS 1604
N. 19TH STREET, TAMPA, FLORIDA 33605 In addition
to him/herself, owner designates Phillip H. Gerardi of 1604 N. 19th St., Tampa, FLORIDA 33605 Name) (Address)
to receive
a copy of Lienor's Notice as provided in SECTION 713.13 •1 (b) FLORIDA STATUTES. EXPIRATION DATE
OF NOTICE -OMMEN NT a Year from date of recording, unless specified. SIGNATURE OF
OWNER/AGENT PRINTED NAME '
0— 1 /CERTIFICATION
STATE
OF
C 1 N A COUNTY OF 1,QL: A`\ The foregoing
instrument was acknowledged before me this 3% day of JytW 20G by INO-
7 /VV Lt'r/ He is personally known to me or has produced a Mi4W-? LtC.
as indentification rd who (did) (did not) take an oath. INETRI C. BRAZIL Commission Number (Stamp)
Notary Public -m
E Notary Public - California f x3"' MY COMM,
EXplrea May 16, 2010
SimplexGrinnell BE
SAFE.
tqCI7 Fire &Building
Products
Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500
Series TY-FRB — 2.8, 4.2, 5.6, and 8.0 K-factor
Upright, Pendent, and Recessed Pendent Sprinklers
Quick Response, Standard Coverage
General
Description
The Series TY-FRB, 2.8, 4.2, 5.6, and
8.0 K-factor, Upright and Pendent
Sprinklers described in this data sheet
are quick response - standard cover-
age, decorative 3 mm glass bulb type
spray sprinklers designed for use in
light or ordinary hazard, commercial
occupancies such as banks, hotels,
shopping malls, etc.
The recessed version of the Series
TY-FRB Pendent Sprinkler, where ap-
plicable, is intended for use in areas
with a finished ceiling. It uses either a
two-piece Style 10 (1/2 inch NPT) or
Style 40 (3/4 inch NPT) Recessed Es-
cutcheon with 1/2 inch (12,7 mm) of
recessed adjustment or up to 3/4 inch
19,1 mm) of total adjustment from the
flush pendent position, or a two-piece
Style 20 (1/2 inch NPT) or Style 30 (3/4
inch NPT) Recessed Escutcheon with
1/4 inch (6,4 mm) of recessed adjust-
ment or up to 1/2 inch (12,7 mm) of
total adjustment from the flush pen-
dent position. The adjustment provided
by the Recessed Escutcheon reduces
the accuracy to which the fixed pipe
drops to the sprinklers must be cut.
Corrosion resistant coatings, where
applicable, are utilized to extend the
life of copper alloy sprinklers beyond
that which would otherwise be ob-
tained when exposed to corrosive at -
IMPORTANT
Always refer to Technical Data
Sheet TFP700 for the "INSTALLER
WARNING" that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Page 1 of 8
mospheres. Although corrosion resis-
tant coated sprinklers have passed the
standard corrosion tests of the appli-
cable approval agencies., the testing is
not representative of all possible cor-
rosive atmospheres. Consequently, it
is recommended that the end user be
consulted with respect to the suitability
of these coatings for any given corro-
sive environment. The effects of ambi-
ent temperature, concentration of
chemicals, and gas/chemical velocity,
should be considered, as a minimum,
along with the corrosive nature of the
chemical to which the sprinklers will be
exposed.
An intermediate level versions of the
Series TY-FRB Pendent Sprinklers are
detailed in Technical Data Sheet
TFP356, and Sprinkler Guards are de-
tailed in Technical Data Sheet TFP780
WARNINGS
The Series TY-FRB :sprinklers de-
scribed herein must be installed and
maintained in compliance with this
document, as well as with the applica-
ble standards of the National Fire Pro-
tection Association, in addition to the
standards of any other authorities hav-
ing jurisdiction. Failure to do so may
impair the performance of these de-
vices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Model/Sprinkler
Identification
Numbers
TY1131 - Upright 2.81K, 1/2"NPT
TY1231 - Pendent 2.81K, 1/2"NPT
TY2131 - Upright 4.21K, 1/2"NPT
TY2231 - Pendent 4.21K, 1/2"NPT
TY3131 - Upright 5.6K, 1/2"NPT
JULY, 2004
TY3231 - Pendent 5.6K, 1/2"NPT
TY4131 - Upright 8.01K, 3/4"NPT
TY4231 - Pendent 8.01K, 3/4"NPT
Technical
Data
Approvals
UL and C-UL Listed.
FM, LPCB, and NYC Approved.
Refer to Table A for complete approval
information including corrosion resis-
tant status.)
Maximum Working Pressure
175 psi (12,1 bar)
Discharge Coefficient
K = 2.8 GPM/psis/2 (40,3 LPM/barli2)
K = 4.2 GPM/psili2 (60,5 LPM/barli2)
K = 5.6 GPM/psili2 (80,6 LPM/barli2)
K = 8.0 GPM/psis/2 (115,2 LPM/bars/2)
Temperature Ratings
Refer to Table A and B
TFP171
Page 2 of 8
ESCUTCHEON 7/16' (11,1 mm) STYLE 10 or' 0
PLATE SEATING , ** NOMINAL RECESSED
SSU* SURFACE NPT MAKE-IN ESCUTCHEON
DEFLECTOR
T_ / 7/16'
2-1/4"
57,2 mm) (
11,1 mm)
NOMINAL
MAKE -IN
1-9/16" 'T39,7 mm) WRENCH
FLATS
SSP DEFLECTOR' 2-7/8' (73,0 mm) DIA. —_a 1/2- NPT''
PENDENT RECESSED PENDENT UPRIGHT
TFP171
CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression 7 - Bushing orifice seat on frame.
Screw **
Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 1
QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY1131) AND PENDENT (TY1231) SPRINKLERS
2.8 K-FACTOR, 112 INCH NPT
ESCUTCHEON 7/16' (11,1 mm)
PLATE SEATING
1/2, **
NOMINAL
SURFACE
NPT
MAKE -IN
F_
1 1
2-3/16'
55,6 mm)
1-1/2*
38,1 mm)
STYLE 10 or 20
RECESSED
SSU' ESCUTCHEON
SSP DEFLECTOR* 2-7/8' (73,0 mm) DIA.
INOMINAL I7I
r r j' WRENCHI
FLATE___ rf
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame.
Screw **
Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 2
QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY2131) AND PENDENT (TY2231) SPRINKLERS
4.2 K-FACTOR, 112 INCH NPT
Finishes Bulb . . . . . . . . . . . . . . Glass
Sprinkler: Refer to Table A and B Compression Screw . . . Bronze
Recessed Escutcheon: White Coated, Deflector . . . . . . . Copper/Bronze
Chrome Plated, or Brass Plated Bushing (K=2.8) . . . . . . . Bronze
Physical Characteristics
Frame . . . . . . . . . . Bronze
Button . . . . . . . . . Brass/Copper
Sealing Assembly . . . . . . . .
Beryllium Nickel w/Teflont
Operation
The glass Bulb contains a fluid which
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass Bulb, allowing the sprinkler to
activate and water to flow.
s
ca
E
ro
a
N
0
a-
0
TFP171
ESCUTCHEON 7/16" (11,1 mm)
PLATE SEATING
1/2, **
NOMINAL
SURFACE
NPT
MAKE -IN
T_
2-3/16"
55,6 mm)
1-1/2'
38,1 mm)
STYLE 10 or 20
RECESSED
SSU' ESCUTCHEON
SSP DEFLECTOR* 2-7/8" (73,0 mm) DIA.
DEFLECTOR
7/16"
11,1 mm)
NOMINAL
MAKE -IN
2 3/16'
WRENGH (55,6 mm)
FLATS
I 1/2' NPT"`
Page 3 of 8
6"
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector ' Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame.
Screw "
Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 3
QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY3131) AND PENDENT (TY3231) SPRINKLERS
5.6 K-FACTOR, 1/2 INCH NPT
ESCUTCHEON 1/2" (12,7 mm) STYLE 30 or 40
PLATE SEATING .* NOMINAL RECESSED ,
SURFACE 3/4' MAKE -IN ESCUTCHEON SSU
NPT DEFLECTOR
r— 1/2° 5
2-5/16`
5
12,7 mm)
58,7 mm) NOMINAL 4
MAKE -IN
1-9/16° 2-1/4' 2
39,7 mm) W REN(:H (57,2 mm) WFLATS 3
1
SSP DEFLECTOR* 2 7/8' (73,0 mm) DIA. 3/4` NPT **
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector " Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame.
Screw
Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 4
QUICK RESPONSE SERIES TY-FRB UPRIGHT (TY4131) AND PENDENT (TY4231) SPRINKLERS
8.0 K-FACTOR, 3/4 INCH NPT
Design
Criteria
The Series TY FRB Pendent and Up-
right Sprinklers are intended for fire
protection systems designed in ac-
cordance with the standard installation
rules recognized by the applicable
Listing or Approval agency (e.g., UL
Listing is based on the requirements of
NFPA 13, and FM Approval is based
on the requirements of FM's Loss Pre-
vention Data Sheets ). Only the Style
10, 20, 30, or 40 Recessed Escutch-
eon, as applicable, is to be used for
recessed pendent installations.
Installation
The Series TY-FRB Sprinklers must be
installed in accordance with the follow-
ing instructions:
NOTES
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss of
liquid from the bulb. With the sprinkler
Page 4 of 8
SPRINKLER FINISH (See Note 7)
K TYPE TEMP. BULB
LIQUID
NATURAL
BRASS
CHROME
PLATED
WHITE"'
POLYESTER
2.8
PENDENT
TY1231
and
UPRIGHT
TY1131)
135°F/57°C Orange
1,2,3,5
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
286°F/141 °C Blue
1/2'
NPT
PENRECDENT
TY1231)'
Figure 5
135°F/57°C Orange
1, 2, 5
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
RECESSED
TY1231)"
Figure 6
135°F/57°C Orange
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
4.2
1/2'
NPT
PENDENT
TY2231)
and
UPRIGHT
TY2131)
135°F/57°C Orange
1 2
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
286°F/141°C Blue
RECESSED
PENDENT
TY2231)'
Figure 7
135°F/57°C Orange
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
RECESSED
PENDENT
TY2231)"
Figure 8
135°F/57°C Orange
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprin tiers.
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response
Sprinklers.
3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprin-
kle rs.
5. Approved by the City of New York under MEA 354-01-E.
7. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed, the sprin-
klers are UL and C-UL Listed as Corrosion Resistant Sprinklers.
Installed with Style 10 (1/2' NPT) or Style 40 (3/4' NPT) 3/4' Total Adjustment
Recessed Escutcheon, as applicable.
Installed with Style 20 (1/2' NPT) or Style 30 (3/4' NPT) 1/2' Total Adjustment
Recessed Escutcheon, as applicable.
Frame and Deflector only. Listings and approvals apply to color (Specia; Order).
N/A: Not Available
TABLE A
LABORATORY LISTINGS AND APPROVALS
2.8 AND 4.2 K-FACTOR SPRINKLERS
held horizontally, a small air bubble A leak tight 112 inch NPT sprinkler joint
should be present. The diameter of the should be obtained with a torque of 7
air bubble is approximately 1116 inch to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-
1,6 mm) for the 1351F157°C to 3132 mum of 21 ft. lbs. (28,5 Nm) of torque
inch (2,4 mm) for the 286°F1141 °C may be used to install .sprinklers with
temperature ratings. 112 NPT connections. A leak tight 314
TFP171
inch NPT sprinkler joint should be ob-
tained with a torque of 10 to 20 ft.lbs.
13,4 to 26,8 Nm). A maximum of 30
ft.lbs. (40,7 Nm) of torque is to be used
to install sprinklers with 314 NPT con-
nections. Higher levels of torque may
distort the sprinkler inlet and cause
leakage or impairment of the sprinkler.
Do not attempt to make-up for insuffi-
cient adjustment in the escutcheon
plate by under- or over -tightening the
sprinkler. Readjust the position of the
sprinkler fitting to suit.
The Series TY-FRB Pendent and Up-
right Sprinklers must be installed in
accordance with the following instruc-
tions.
Step 1. Pendent sprinklers are to be
installed in the pendent position, and
upright sprinklers are to be installed in
the upright position.
Step 2. With pipe thread sealant ap-
plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
Step 3. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
6 Sprinkler Wrench (Ref. Figure 13).
With reference to Figures 1, 2, 3, and
4, the W-Type 6 Sprinkler Wrench is to
be applied to the sprinkler wrench
flats.
The Series TY-FRB Recessed Pen-
dent Sprinklers must be installed in
accordance with the following instruc-
tions.
Step A. After installing the Style 10.
20, 30, or 40 Mounting Plate, as appli-
cable, over the sprinkler threads and
with pipe thread sealant applied to the
pipe threads, hand tighten the sprin-
kler into the sprinkler fitting.
Step B. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
7 Recessed Sprinkler Wrench (Ref.
Figure 14). With reference to Figure 1,
2, 3, and 4, the W-Type 7 Recessed
Sprinkler Wrench is to be applied to
the sprinkler wrench flats.
Step C. After the ceiling has been in-
stalled or the finish coat has been ap-
plied, slide on the Style 10, 20, 30, or
40 Closure over the Series TY-FRB
Sprinkler and push the Closure over
the Mounting Plate until its flange
comes in contact with the ceiling.
TFP171 Page 5 of 8
SPRINKLER FINISH (See Note 8)
K TYPE TEMP. BULB
LIQUID
NATURAL
BRASS
CHROME
PLATED
WHITE"'
POLYESTER
LEAD
COATED
5.6
1/2°
PENDENT
TY3231)
and
UPRIGHT
TY3131)
135°F/57°C Orange
1, 2, 3, 4, 5, E•, 7 1, 2, 3, 5
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
286°F/141°C Blue
NPT
RECESSED
PENDENT
TY3231)'
Figure 9
135°F/57°C Orange
1, 2, 4, 5 N/A
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
RECESSED
PENDENT
TY3231)"
Figure 10
135°F/57°C Orange
1, 2, 3, 4, 5 1, 2, 4, 5 N/A
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
8.0
3/4'
PENDENT
TY4231
and
UPRIGHT
TY4131)
135°F/57°C Orange
1, 2, 3, 4, 5, 6, 7
1, 2, 5
155°F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
286°F/141 °C Blue
NPT
RECESSED
PENDENT
TY4231)'
Figure 11
135°F/57°C Green
1, 2, 4, 5 N/A
155°F/68°C Orange
175°F/79°C Red
200°F/93°C Yellow
RECESSED
PENDENT
TY4231)"
Figure 12
135°F/57°C Orange
1, 2, 3, 4, 5 N/A
1550F/68°C Red
175°F/79°C Yellow
200°F/93°C Green
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers.
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinklers.
3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers.
4. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/04) as Quick Response Sprinklers; however, the
LPCB does not rate the thermal sensitivity of recessed sprinklers.
5. Approved by the City of New York under MEA 354-01-E.
6. VdS Approved (For details contact Tyco Fire 8 Building Products, Enschede, Netherlands, Tel. 31-53-428-4444/Fax 31-53-428-3377).
7. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) as Quick Response Sprinklers.
8. Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as
Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as a
Corrosion Resistant Sprinklers.
Installed with Style 10 (1/2' NPT) or Style 40 (3/4' NPT) 3/4' Total Adjustment Recessed Escutcheon, as applicable.
Installed with Style 20 (1/2' NPT) or Style 30 (3/4' NPT) 1/2' Total Adjustment Recessed Escutcheon, as applicable.
Frame and Deflector only. Listings and approvals apply to color (Special Order).
N/A: Not Available
TABLE B
LABORATORY LISTINGS AND APPROVALS
5.6 AND 8.0 K-FACTOR SPRINKLERS
Page 6 of 8
2-7/8' DIA.
5/8t1/4' (
73,0 mm) 3/4' 19,1 mm
15,9t6,4 mm) 2-1/4' DIA. 1/4' (6,4 mm)
FACE OF (57,2 mm)
MOUNTING
SPRINKLER PLATE
FITTING
1/8'
3,2 mm)
T
MOUNTING
SURFACE
CLOSURE SERIES 1-5116' 33,3 mm)
TY-FRB 13/16' (20,6 mm)
FIGURE 5
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 314 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON
2.8 K-FACTOR, 112 INCH NPT
2-7/8' DIA.
5/8t1/4' (
73,0 mm) 3/4' (19,1 mm)
15,9t6,4 mm) 2-1/4' DIA. 1/4' (6,4 mm)
FACE OF (57,2 mm)
MOUNTING
SPRINKLER PLATE
FITTING
1/8'
3,2 mm)
MOUNTING
SURFACE
CLOSURE SERIES 1-1/4'(31,8 mm)
TY-FRB 3/4' (19,1 mm)
FIGURE 7
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 314 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON
4.2 K-FACTOR, 112 INCH NPT
Care and
Maintenance
The Series TY-FRB Sprinklers must be
maintained and serviced in accord-
ance with the following instructions:
NOTES
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shutdown the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notified.
Absence of an escutcheon, which is
TFP171
2-7/8' DIA.
1/2t1/8' (
73,0 mm)
1/2• 12,7 mm
12,7t3,2 mm) 2-1/4' DIA. 1/4' (6,4 mm)
FACE OF (57,2 mm)
MOUNTING
SPRINKLER PLATE
FITTING
1/8'
3,2 mm)
MOUNTING
SURFACE
CLOSURE SERIES 1-5/16' 33,3 mm
TY-FRB 1-1/16' (27,0 mm)
FIGURE 6
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 112 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
2.8 K-FACTOR, 112 INCH NPT
2-7/8' DIA.
1/2t1/8' (
73,0 mm)
1/2' (12,7 mm)
12,7:3,2 mm) 2-1/4' DIA. 1/4' (6,4 mm)
FACE OF (57,2 mm)
MOUNTING
SPRINKLER
7-1 PLATE
FITTING
3,2;mm)
MOUNTING
SURFACE
CLOSURE SERIES 1-1/4' 31,8 mm
TY-FRB 1' (25,4 mm)
FIGURE 8
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 112 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
4.2 K-FACTOR, 112 INCH NPT
used to cover a clearance hole, may
delay the time to sprinkler operation in
a fire situation.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
fied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush.
Care must be exercised to avoid dam-
age to the sprinklers - before, during,
and after installation. Sprinklers dam-
aged by dropping, striking, wrench
twist/slippage, or the like, must be re-
placed. Also, replace any sprinkler that
has a cracked bulb or that has lost
liquid from its bulb. (Ref. Installation
Section).
Frequent visual inspections are rec-
ommended to be initially performed for
corrosion resistant coated sprinklers,
after the installation has been com-
pleted, to verify the integrity of the cor-
rosion resistant coating. Thereafter,
annual inspections per NFPA 25
should suffice; however, instead of in-
specting from the floor level, a random
sampling of close-up visual inspec-
tions should be made, so as to better
determine the exact sprinkler condi-
TFP171
2.7/8' DIA.
5/8t1/4' (
73,0 mm) 3/4' 19,1 mm)
15,9t6,4 mm) -1' DIA. 1/4' (6,4 mm) 2/4
FACE OF (57,2 mm)
MOUNTING
SPRINKLER PLATE
FITTING
1/8'
3,2 mm)
T
MOUNTING
SURFACE
CLOSURE
SERIES 1-1/4' 31,8 mm)
TY-FRB 3/4' (19,1 mm)
FIGURE 9
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON
5.6 K-FACTOR, 1/2 INCH NPT
2-7/8' DIA.
5/8t1/4' (
73,0 mm) 3/4' (19,1 mm)
15,9t6,4 mm) 2-1/4' DIA. 1/4' (6,4 mm)
FACE OF (
57,2 mm)
MOUNTING
SPRINKLER PLATE
FITTING
8'
3,21/mm)
MOUNTING
SURFACE
CLOSURE SERIES 1.5/16' (33,3 mm)
TY-FRB 13/16' (20,6 mm)
FIGURE 11
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 40 RECESSED ESCUTCHEON
8.0 K-FACTOR, 3/4 INCH NPT
tion and the long term integrity of the
corrosion resistant coating, as it may
be affected by the corrosive conditions
present.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
facturer should be contacted relative to
any questions.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a qualified
Inspection Service in accordance with
Page 7 of 8
2-7/8' DIA.
1/2t1B' (
73,0 mm)
1/2' 12,7 mm
12,7t3,2 mm) 2-1/4' DIA. J 1/4' (6,4 mm)
FACE OF (57,2 mm) -I MOUNTING
SPRINKLER PLATE
FITTING
1/8'
MOUNTING
SURFACE
CLOSURE
SERIES 1-1/4' (31,8 mm
TY-FRB 1' (25,4 mm)
FIGURE 10
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
5.6 K-rACTOR, 1/2 INCH NPT
2.7/8' DIA.
1/2t1/8' (
73,0 mm) 1/2' 12,7 mm
12,7t3,2 mm) 2-1/4' DIA. J 1/4' (6,4 mm)
FACE OF (
57,2 mm) I MOUNTING
SPRINKLER PLATE
FITTING
I 1/8'
3 2 mm)
MOUNTING
SURFACE
CLOSURE SERIES
TY-FRB
1-5/16' 33,3 mm
1-1/16' (27,0 mm)
FIGURE 12
SERIES TY-FRB RECESSED PENDENT
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 30 RECESSED ESCUTCHEON
8.0 K-FACTOR, 3/4 INCH NPT
WRENCH RECESS
END 'A' USED FOR
1/2' NPT MODELS)
WRENCH RECESS
END'B' USED FOR
3/4' NPT MODELS)
FIGURE 13
W-TYPE 6 SPRINKLER
WRENCH
local requirements and/or national
codes.
WRENCH
RECESS
PUSH WRENCH
IN TO ENSURE
ENGAGEMENT
WITH SPRINKLER
WRENCHING AREA
FIGURE 14
W-TYPE 7 RECESSED
SPRINKLER WRENCH
Page 8 of 8
P/N 57-XXX-X-XXX
L
MODEUSIN
330 2.8K UPRIGHT (1/2'NPT) TY1131
331 2.8K PENDENT (1/2'NPT) TY1231
340 4.2K UPRIGHT (1/2'NPT) TY2131
341 4.2K PENDENT (1/2'NPT) TY2231
370 5.6K UPRIGHT (1/2'NPT) TY3131
371 5.6K PENDENT (1/2"NPT) TY3231
390 8.OK UPRIGHT (3/4'NPT) TY4131
391 8.OK PENDENT (3/4'NPT) TY4231
Limited
Warranty
TFP171
SPRINKLER I
135
NATURAL BRASS 155
WHITE POLYESTER 175
y WHITE (RAL9010)' 200
CHROME PLATED 286
LEAD COATED
TEMPERATURE
RATING
135°F/57°C
1 155'F/68°C
4 175°Fl79°C
3 200°F/93°C
9 286'F/141"C
7
Eastern Hemisphere sales only.
TABLE C
PART NUMBER SELECTION
SERIES TY-FRB PENDENT AND UPRIGHT SPRINKLERS
Products manufactured by Tyco Fire
Products are warranted solely to the
original Buyer for ten (10) years
against defects in material and work-
manship when paid for and properly
installed and maintained under normal
use and service. This warranty will ex-
pire ten (10) years from date of ship-
ment by Tyco Fire Products. No war-
ranty is given for products or
components manufactured by compa-
nies not affiliated by ownership with
Tyco Fire Products or for products and
components which have been subject
to misuse, improper installation, corro-
sion, or which have not been installed,
maintained, modified or repaired in ac-
cordance with applicable Standards of
the National Fire Protection Associa-
tion, and/or the standards of any other
Authorities Having Jurisdiction. Mate-
rials found by Tyco Fire Products to be
defective shall be either repaired or
replaced, at Tyco Fire Products' sole
option. Tyco Fire Products neither as-
sumes, nor authorizes any person to
assume for it, any other obligation in
connection with the sale of products or
parts of products. Tyco Fire Products
shall not be responsible for sprinkler
system design errors or inaccurate or
incomplete information supplied by
Buyer or Buyer's representatives.
IN NO EVENT SHALL TYCO FIRE
PRODUCTS BE LIABLE, IN CON-
TRACT, TORT, STRICT LIABILITY OR
UNDER ANY OTHER LEGAL THE-
ORY, FOR INCIDENTAL, INDIRECT,
SPECIAL OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT
LIMITED TO LABOR CHARGES, RE-
GARDLESS OF WHETHER TYCO
FIRE PRODUCTS WAS INFORMED
ABOUT THE POSSIBILITY OF SUCH
DAMAGES, AND IN NO EVENT
SHALL TYCO FIRE PRODUCTS' LI-
ABILITY EXCEED AN AMOUNT
EQUAL TO THE SALE; PRICE.
THE FOREGOING WARRANTY IS
MADE IN LIEU OF ANY AND ALL
OTHER WARRANTIES EXPRESS OR
IMPLIED, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PUR-
POSE.
Ordering
Procedure
Owd?imbygutl local distributor for avail-
ablfky indicate the
full product
name. Refer to
the Price List for
complete listing
of Part Numbers.
Sprinkler Assemblies with NPT
Thread Connections:
Specify: (Specify Model/SIN), Quick
Response, (specify K-factor), (specify
temperature rating), Series TY-FRB
specify Pendent or Upright) Sprinkler
with (specify type of finish or coating),
P/N (specify from Table 0).
Recessed Escutcheon:
Specify: Style (specify) Recessed Es-
cutcheon with (specify finish), P/N
specify).
1/2' If mm)
Style 10
Chrome Plated ............ P/N 56-701-9-010
White Coated ............. P/N 56-701-4-010
White RAL9010'........... P/N 56-701-3-010
Brass Plated .............. P/N 56-701-2-010
1/2' (15 mm)
Style 20
Chrome Plated ............ P/N 56-705-9-010
White Coated ............. P/N 56-705-4-010
White RAL9010'........... P/N 56-705-3-010
Brass Plated .............. P/N 56-705-2-010
314' (20 mm)
Style 30
Chrome Plated ............ P/N 56-705-9-011
White Coated ............. P/N 56-705-4-011
White RAL9010'........... P/N 56-705-3-011
Brass Plated .............. P/N 56-705-2-011
3/4' (20 mm)
Style 40
Chrome Plated ............ P/N 56-700.9-010
White Coated ............. P/N 56-700.4-010
White RAL9010'........... P/N 56-700-3-010
Brass Plated .............. P/N 56-700.2-010
Eastern Hemisphere sales only.
Sprinkler Wrench:
Specify: W-Type 6 Sprinkler Wrench,
P/N 56-000-6-387.
Specify: W-Type 7 Sprinkler Wrench,
P/N 56-850-4-001.
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446
tqCLI Fire &Building
Products
Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500
Series RFII — 5.6 K-factor
Royal Flush 11" Pendent Concealed Sprinklers
Quick & Standard Response, Standard Coverage
General
Description
The Series RFII Quick Response
3 mm bulb) & Standard Response (5
mm bulb), 5.6 K-Factor, "Royal Flush
II" Concealed Pendent Sprinklers are
decorative sprinklers featuring a flat
cover plate designed to conceal the
sprinkler. It is the best choice for archi-
tecturally sensitive areas such as hotel
lobbies, office buildings, churches,
and restaurants.
Each unit includes a Cover Plate As-
sembly that conceals the sprinkler op-
erating components above the ceiling.
The separable two-piece design of the
Cover Plate and Support Cup Assem-
blies allows installation of the sprin-
klers and pressure testing of the fire
protection system prior to installation
of a suspended ceiling or application
of the finish coating to a fixed ceiling.
They also permit removal of sus-
pended ceiling panels for access to
building service equipment without
having to first shut down the fire pro-
tection system and remove sprinklers.
Also, the separable two-piece design
of the the Sprinkler provides for 1/2
inch (12,7 mm) of vertical adjustment,
to reduce the accuracy to which the
length of fixed pipe drops to the sprin-
klers must be cut.
The Series RFII Sprinklers are
shipped with a Disposable Protective
IMPORTANT
Always refer to Technical Data
Sheet TFP700 for the "INSTALLER
WARNING" that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Page 1 of 4
Cap. The Protective Cap is temporarily
removed for installation, and then it
can be replaced to help protect the
sprinkler while the ceiling is being in-
stalled or finished. The tip of the Pro-
tective Cap can also be used to mark
the center of the ceiling hole into plas-
ter board, ceiling tiles, etc. by gently
pushing the ceiling product against the
Protective Cap. When the ceiling in-
stallation is complete the Protective
Cap is removed and the Cover Plate
Assembly installed.
As an option, the Series RFII Standard
Response (5 mm bulb) "Royal Flush II"
Concealed Pendent Sprinklers may be
fitted with a silicone Air and Dust Seal
Ref. Fig. 5). The Air and Dust Seal is
intended for sensitive areas where it is
desirable to stop air and dust travel
through the cover plate from the area
above the ceiling.
WARNINGS
The Series RFII Concealed Pendent
Sprinklers described herein must be
installed and maintained in compli-
ance with this document, as well as
with the applicable standards of the
National Fire Protection Association,
in addition to the standards of any
other authorities having jurisdiction.
Failure to do so may impair the per-
formance of these devices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Model/Sprinkler
Identification
Numbers
TY3551 (5mm bulb) & TY3531 (3 mm
bulb): maximum 175 psi (12,1 bar) by
UL, C-UL, FM, LPCB and NYC.
TY3504 (5 mm bulb) & TY3505 (3 mm
bulb): maximum 250 psi (17,3 bar) by
JULY, 2004
UL, C-UL, and NYC. Maximum 175
psi (12,1 bar) by FM.
Technical
Data
Approvals for Series RFII
UL and C-UL Listed. FM Approved.
NYC under MEA 353-01-E. LPCB (Ref.
No. 094a/09 for TY3551 & 094a/10 for
TY3531) Approved.
The approvals apply only to the serv-
ice conditions indicated in the Design
Criteria section and maximum pres-
sure ratings indicated in the
Model/Sprinkler Identification Num-
bers section.
Approvals for Air & Dust Seal
Part #10908100)
UL and C-UL Listed for use with the
RFII (TY3551 & TY3504) Standard Re-
sponse Concealed Sprinkler.
Temperature Ratings
155F/68C Sprinkler - 135F/57C Plate
200F/93C Sprinkler - 165F/74C Plate
Discharge CoefliFient
K = 5.6 GPM/psi (80,6 LPM/bars/2)
Adjustment
1/2 inch (12,7 mm)
Finishes
Cover Plate: Chrome Plated, Brass
Plated, or White Painted (Custom paint
matches and colors other than white
are available on request.)
TFP181
Page 2 of 4
Physical Characteristics
Frame . . . . . . . . . . Bronze
Support Cup . Chrome Plated Steel
Guide Pins . . . . . . Stainless Steel
Deflector . . . . . . . . . . . Bronze
Compression Screw . . . . . . Brass
Bulb . . . . . . . . . . . . . . . Glass
Cap . . . . . . . . Bronze or Copper
Sealing Assembly .
Beryllium Nickel w/Teflon'
Cover Plate . . . . . . . . . . . Brass
Retainer . . . . . . . . . . Brass
Ejection Spring . . . . Stainless Steel
Patents
U.S.A. 4,014,388
Operation
When exposed to heat from a fire, the
Cover Plate, which is normally sol-
dered to the Retainer at three points,
falls away to expose the Sprinkler As-
sembly. At this point the Deflector sup-
ported by the Guide Pins drops down
to its operational position.
The glass Bulb contains a fluid that
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass Bulb, activating the sprinkler and
allowing water to flow.
Design
Criteria
The RFII (TY3551 & TY3504), 5 mm
Bulb Type, Concealed Pendent Sprin-
klers are UL and C-UL Listed as stand-
ard response - standard spray sprin-
klers for use in accordance with the
current NFPA standard. They are FM
Approved as standard response -
standard spray sprinklers for use in
accordance with the current FM Loss
Prevention Data Sheets.
The RFII (TY3531 & TY3505) 3 mm
Bulb Type, Concealed Pendent Sprin-
klers are UL and C-UL Listed as quick
response - standard spray sprinklers
for use in accordance with the current
NFPA standard. They are FM Ap-
proved as standard response - stand-
ard spray sprinklers for use in accord-
ance with the current FM Loss
Prevention Data Sheets.
The Series RFII Concealed Pendent
Sprinklers are only listed and ap-
proved with the Series RFII Concealed
Cover Plates having a metallic or white
painted finish.
The Series RFII must not be used in
applications where the air pressure
above the ceiling is greater than that
below. Down drafts through the Sup-
port Cup could delay sprinkler opera-
tion in a fire situation.
TFP181
1/2' NPT SEALING
ASSEMBLY
FRAME \
CAP
SUPPORT
CUP WITH BULB
ROLL FORMED
THREADS
COMPRESSION
GUIDE
SCREW
PINS (2)
DEFLECTOR
DROPPED
DEFLECTOR
I r=Ji-L-- -------- - POSITION)
SPRINKLER/SUPPORT CUP
ASSEMBLY
THREADINTO RETAINER
SUPPORT CUP WITH THREAD
UNTIL MOUNTING O O / DIMPLES
SURFACE IS
FLUSH WITH EJECTION
CEILING SPRING
SOLDER COVER
TABS (3) COVER PLATE/RETAINER PLATE
ASSEMBLY
FIGURE 1
SERIES RFII CONCEALED SPRINKLER
ASSEMBLY
Installation
The Series RFII must be installed in
accordance with the following instruc-
tions:
NOTES
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss of
liquid from the bulb. With the sprinkler
held horizontally, a small air bubble
should be present. The diameter of the
air bubble is approximately 1116 inch
1,6 mm) for the 155°F/68°C and 3/32
inch (2,4 mm) for the 200°F/93°C tem-
perature ratings.
A leak tight 112 inch NPT sprinkler joint
should be obtained with a torque of 7
to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-
mum of 21 ft.lbs. (28,5 Nm) of torque
is to be used to install sprinklers.
Higher levels of torque may distort the
sprinkler inlet with consequent leak-
age or impairment of the sprinkler.
Do not attempt to compensate for in-
sufficient adjustment in the Sprinkler
Assembly by under- or over -tightening
the Sprinkler/Support Cup Assembly.
Readjust the position of the sprinkler
fitting to suit.
Step 1. The sprinkler must only be
installed in the pendent position and
with the centerline of the sprinkler per-
pendicular to the mounting surface.
Step 2. Remove the Protective Cap.
Step 3. With pipe thread sealant ap-
plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
Step 4. Wrench tighten the sprinkler
using only the RFII Sprinkler Wrench
Ref. Figure 3). The RFII Sprinkler
Wrench is to be applied to the Sprin-
kler as shown in Figure 3.
Step 5. Replace the Protective Cap
Ref. Figure 4) by pushing it upwards
until it bottoms out against the Support
Cup. The Protective Cap helps prevent
damage to the Deflector and Arms dur-
ing ceiling installation and/or during
application of the finish coating of the
ceiling. It may also be used to locate
the center of the clearance hole by
gently pushing the ceiling material up
against the center point of the Protec-
tive Cap.
NOTE
As long as the Protective Cap remains
in place, the system is considered to
be "Out of Service".
Registered Trademark of DuPont
TFP181
FACE OF
SPRINKLER
FITTING
SPRINKLER
SUPPORT CUP
ASSEMBLY
1/2' (12,7 mm)
THREADED
D ADJUSTMENT
FACE OF CEILING,
RETAINING RING
MOUNTING
SURFACE
3/16'to 11/16'
4,8 to 17,5 mm)
REFERENCE
COVER PLATE
PROFILE DEPTH
DIMENSION B
CLEARANCE HOLE
DIAMETER -
DIMENSION C
T--
MANUFACTURER DEFLECTOR
PRESET GAP IN DROPPED
3/32' (2,4 mm) POSITION
COVER PLATE
DIAMETER
DIMENSION A
COVER PLATE
RETAINER
ASSEMBLY
A: 3-1/4' (82,6 mm) C: 2-3/8' to 2-5/8' (60,3 to 66,7 mm)
B: 3/16' (4,8 mm) D: 1-3/4' to 2-1/4' (44,5 to 57,E mm)
FIGURE 2
SERIES RFII CONCEALED SPRINKLER
INSTALLATION DIMENSIONS
FRAME
ARM
SUPPORT
CUP
7/8'(23 mm)
SQUARE
ALIGN
J
ARROWS WITH
FRAME ARMS j I al
r
ACCEPTS
1/2'SOCKET
DRIVE
FIGURE 3
RFII SPRINKLER WRENCH
Page 3 of 4
Step 6. After the ceiling has been com-
pleted with the 2-1/2 inch (63,5 mm)
diameter clearance hole and in prepa-
ration for installing the Cover Plate As-
sembly, remove and discard the Pro-
tective Cap, and verify that the
Deflector moves up and down freely. If
the Sprinkler has been damaged and
the Deflector does not move up and
down freely, replace the entire Sprin-
kler assembly. Do not attempt to mod-
ify or repair a damaged sprinkler.
Step 7. When installing an Air and
Dust Seal, refer to Figure 5, otherwise
proceed to Step 8. To attach the Air and
Dust Seal, verify the angle of the out-
side edge of the seal is oriented ac-
cording to Figure 5. Start the edge of
the Retainer in the grooved slot of the
Air and Dust Seal and continue around
the retainer until the entire Air and
Dust Seal is engaged.
NOTE
The Air and Dust Seal is only to be
installed on the periphery of the Re-
tainer.
Step 8. Screw on the Cover Plate/Re-
tainer Assembly until the Retainer -
Figure 2 (or Air and Dust Seal - Figure
5) contacts with the ceiling. Do not
continue to screw on the Cover
Plate/Retainer Assembly such that it
lifts a ceiling panel out of its normal
position. If the Cover Plate/Retainer
Assembly cannot be engaged with the
Support Cup or the Cover Plate/Re-
tainer Assembly cannot be engaged
sufficiently to contact the ceiling, the
Sprinkler Fitting must be repositioned.
Care and
Maintenance
The Series RFII must be maintained
and serviced in accordance with the
following instructions:
NOTES
Absence of the Cover Plate Assembly
may delay sprinkler operation in a fire
situation.
Page 4 of 4
When properly installed, there is a
nominal 3132 inch (2,4 mm) air gap
between the lip of the Cover Plate and
the ceiling, as shown in Figure 2. This
air gap is necessary for proper opera-
tion of the sprinkler. If the ceiling is to
be repainted after the installation of
the Sprinkler, care must be exercised
to ensure that the new paint does NOT
seal off any of the air gap.
Factory painted Cover Plates MUST
NOT be repainted. They should be re-
placed, if necessary, by factory
painted units.
Do not pull the Cover Plate relative to
the Enclosure. Separation may result.
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shut down the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notified.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
fied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush.
Care must be exercised to avoid dam-
age to the sprinklers - before, during,
and after installation. Sprinklers dam-
aged by dropping, striking, wrench
twist/slippage, or the like, must be re-
placed. Also, replace any sprinkler that
has a cracked bulb or that has lost
liquid from its bulb. (Ref. Installation
Section).
If a sprinkler must be removed, do not
reinstall it or a replacement without
reinstalling the Cover Plate Assembly.
If a Cover Plate Assembly becomes
dislodged during service, replace it im-
mediately.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
facturer should be contacted relative to
any questions.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a qualified
TFP181
SUPPORT SPRINKLER FACE OF ORIENT
CUP CEILING SEAL
BEVELAS
SHOWN
COVER
PLATE
RETAINER
ASSEMBLY
CLEAN
ROOM
LIP OF COVER SEAL
RETAINER PLATE
FIGURE 5
OPTIONAL AIR AND DUST SEAL FOR SERIES RFII (TY3551 & TY3504)
Inspection Service in accordance with
local requirements and/or national
codes.
Limited
Warranty
Products manufactured by Tyco Fire
Products are warrantee solely to the
original Buyer for tern (10) years
against defects in material and work-
manship when paid for and properly
installed and maintained under normal
use and service. This warranty will ex-
pire ten (10) years from date of ship-
ment by Tyco Fire Products. No war-
ranty is given for products or
components manufactured by compa-
nies not affiliated by ownership with
Tyco Fire Products or for products and
components which have been subject
to misuse, improper installation, corro-
sion, or which have not been installed,
maintained, modified or repaired in ac-
cordance with applicable Standards of
the National Fire Protection Associa-
tion, and/or the standards of any other
Authorities Having Juri:;diction. Mate-
rials found by Tyco Fire Products to be
defective shall be either repaired or
replaced, at Tyco Fire Products' sole
option. Tyco Fire Products neither as-
sumes, nor authorizes any person to
assume for it, any other obligation in
connection with the sale of products or
parts of products. Tyco Fire Products
shall not be responsible for sprinkler
system design errors or inaccurate or
incomplete information supplied by
Buyer or Buyer's representatives.
IN NO EVENT SHALL TYCO FIRE
PRODUCTS BE LIABLE, IN CON-
TRACT, TORT, STRICT LIABILITY OR
UNDER ANY OTHER LEGAL THE-
ORY, FOR INCIDENTAL, INDIRECT,
SPECIAL OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT
LIMITED TO LABOR CHARGES, RE-
GARDLESS OF WHETHER TYCO
FIRE PRODUCTS WAS INFORMED
ABOUT THE POSSIBILITY OF SUCH
DAMAGES, AND IN NO EVENT
SHALL TYCO FIRE PRODUCTS' Lk
ABILITY EXCEED AN AMOUNT
EQUAL TO THE SALES PRICE.
11 _ _ t,. . _ 1. 1 ::. 1 .
Ordering
Procedure
When placing an order, indicate the full
product name. Contact your local dis-
tributor for availability.
Sprinkler Assembly:
Specify: (SIN), (specify temperature
rating) Series RFII Concealed Pen-
dent Sprinkler, P/N (specify).
155F/68C 200F/93C
TY3551 51.790-1-155 51-790-1-200
TY3504 51-796-1-155 51-796-1-200
TY3531 51-792-1-155 51-792-1-200
TY3505 51-797-1-155 51-797-1.200
Separately Ordered Cover Plate:
Specify: (specify temperature rating)
Series RFII Concealed Cover Plate
with (specify finish), P/N (specify).
135F/57C(a) 165F/74C'(b)
Brass 56-792-1.135 56-792-1-165
Bright Brass 56-792-2-135 56-792-2-165
Chrome 56-792-9-135 56-792-9-165
Brushed Chrome 56-792-8-135 56-792-8-165
White 56-792-0-135 56-792-0-165
White (RAL9010)' 56-792-3-135 56-792-3-165
Bright While 56-792.4.135 56-792-4-165
Off White 56-792-5-135 56-792-5-165
Black 56-792-6-135 56-792-6-165
Custom 56-792-X-135 56-792-X-165
a) For use with 155F/68C sprinklers.
b) For use with 200F/93C sprinklers.
Eastern Hemisphere sales only.
Sprinkler Wrench:
Specify: RFII Sprinkler Wrench,
P/N 56-000-1-075.
Air and Dust Seal:
Specify: Air and Dust Seal,
P/N 56-908-1-001.
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446
FlexHead commercial fire sprinkler connections
n
t
r•
Submittal
i
Package
F
i
AA la.:i1 16dNrf? 9a, '>Oi fk'Al•Y5''y% Jfi.).j ifA' ',pa!_'j: 19'Adi tfa!
IN
FlexHead commercial firs sprinkler connections
WARNING!
These installation instructions are for qua 'fled and/or licensed technicians
in the Fire Protection field ONLY. Consult NFPA, FM, UL, state and local
code guidelines prior to installation.
Failure to follow these specific instruction.s may cause personal injury.
Installation technicians must read the ent re manual prior to attempting
installation of product. During maintenance or inspection of FlexHead
product, facility fire protection system MUST BE INACTIVE. DO NOT
ATTEMPT RELOCATION OR MAINTENANCE WHEN FIRE PROTECTION
SYSTEM IS "LIVE."
Installation Instructions
Tools Required
Standard pipe wrench
Safety glasses
Adjustable wrench
Screwdriver
Materials `Required
Sprinkler pipe thread sealant
Teflon" tape
1. Mounting Bracket Assembly
A. For this step you will need a 3/8" bolt, 1/4" bolt,
universal hub and mounting bracket.
B. Select one of the four sprinkler port location; on
mounting bracket.
C. Thread the 3/8" bolt through side of universal hub.
D. (Photo 1a) Insert tab of universal hub into slot on
mounting bracket as shown.
E. (Photo 1b) Flip bracket over and insert and tighten
1/4" attachment bolt thru pre -punched hole in
bracket until tight as shown.
0
2. Attaching Mounting Bracket
A. (Photo 2) Attach mounting bracket to T-bar
suspended ceiling grid. From above the ceiling,
position FlexHead Mounting Bracket legs on to
T-bar grid so that the selected hole in support
bracket aligns directly above sprinkler head
location in ceiling tile.
B. Position the two clips at the ends of the support
bracket legs on the T-bar grid and push each of
the two clips down to snap in place as shown.
Be sure the center section of the clip is on the
outside of grid and base section is on the inside.
NOTE. For additional support, screw self -tapping
screw through hole in center tab of bracket
into grid.
2A. Optional Attachment for
Mounting Bracket to Metal
Studs/Gypsum Board Ceiling
A. Flip mounting bracket over and install universal
hub on desired sprinkler port location.
B. (Photo 2A) From above the ceiling, position
mounting bracket over metal studs as shown.
Align hole in bracket directly over sprinkler hole
prepared in ceiling. Attach mounting bracket to
metal studs by screwing two 1/4" self -tapping
screws through bracket into grid.
C. Repeat process on opposite end of bracket.
Both ends of bracket should be attached with
two self -tapping screws.
3. Connect FlexHead SprinLer
Drop to Sprinkler Branch Line
A. Apply Teflon tape and pipe sealant to one inch
1") threaded end of FlexHead sprinkler drop per
NFPA guidelines.
B. Attach one inch (1") threaded end of FlexHead
Sprinkler Drop to branch line per NFPA, state and
local code guidelines.
C. (Photo 3) Do not use welded or braided hose section
of FlexHead sprinkler drop for a wrenching sL rface.
Attach FlexHead sprinkler drop using rigid pi )e end
of units as wrenching surface as shown.
4. Secure FlexHead Sprinkler
Drop to Mounting Bracket:
and Attach Sprinkler Head.
A.
B.
C.
Photo 4a) Bend the FlexHead to hold its desired
position. The FlexHead sprinkler drop has a 7"
minimum bend radius per FM guidelines and
minimum bend radius per UL guidelines. Inset
outlet fitting end of FlexHead sprinkler drop
through center hole in previously installed mounting
bracket and hole in ceiling tile. Make sure the hose
is bent sufficiently so that the reducing coupling
sits perfectly vertical in center hole of support
bracket. Do not torque or twist FlexHead during
installation process.
Photo 4B) Attach sprinkler head, properly prepared
with Teflon tape and sealant to FlexHead sprinkler
drop according to NFPA and sprinkler head
manufacturer's guidelines.
Photo 4C) Adjust FlexHead sprinkler drop hei(iht to
accommodate type of sprinkler head. When sprinkler
head is in desired location, tighten the fastening
bolt on center hub of support bracket by turn ng
clockwise with wrench until tight as shown.
5. Completing Installation
A. Test installation of sprinkler system for any
leaks per NFPA guidelines.
B. Install sprinkler escutcheon from below ceiling
per manufacturer's guidelines.
These connections are designed for use in ceilings
with grids that meet ASTM C 635 (Standard
Specification for the Manufacture, Performance,
and Testing of Metal Suspension Systems for
Acoustical Tile and Lay -in Panel Ceilings) and
ASTM C 636 (Standard Practice for Installation of
Metal Ceiling Suspension Systems for Acoustical
Tile and Lay -in Panels) referenced by the IBC. The
three structural classifications are the following:
Light -Duty Systems, Intermediate -Duty Systems
and Heavy -Duty Systems. These connections
have been approved for use in all Intermediate -
Duty and Heavy -Duty structural classifications.
ZI
NFPA 13 Code Language and
Seismic Qualification
NFPA 13 Standard for Installation of Sprinkler Systems
2007 Edition
9.2.1.3.3* Flexible Sprinkler Hose Fittings.
A. 9.2.1.3.3 Examples of areas of use include clean rooms, suspended ceilings, and
exhaust ducts.
9.2.1.3.3.1 Listed flexible sprinkler hose fittings and its anchoring components,
intended for use in installations connecting the sprinkler piping to
sprinklers, shall be installed in accordance with the requirements of the
Listing including any installation instructions.
9.2.1.3.3.2 When installed and supported by suspended ceilings, the ceiling shall meet
ASTM C-635and shall be installed in accordance with ASTM C-636.
9.2.1.3.3.3* When flexible sprinkler hose fittings exceed 6 ft in length and are
supported by a suspended ceiling a hanger(s) attached to the structure
shall be required to ensure that the maximum unsupported length does not
exceed 6 ft.
A. 9.2.1.3.3.3 The committee evaluation of flexible sprinkler hose fittings supported by
suspended ceilings was based upon a comparison of the weight of a 6 ft,
1 in diameter sch 40 water -filled flexible hose fitting weighing
approximately 9 lbs. The information provided to the committee showed
that the maximum load shed to the suspended ceiling by the flexible hose
fitting was approximately 6 lbs and that a suspended ceiling meeting ASTM
C-635, Standard Specification for the Manufacture, Performance, and Testing
of Metal Suspension of Acoustical Tile and Lay -In Panel Celings, and installed
in accordance with ASTM C-636, Standard Practice for Installation of Metal
Ceiling Suspension Systems for Acoustical Tile and Lay -In Panels, can
substancially support the load. In addition, the supporting material showed
that the flexible hose connection can be attached to the suspended ceilings
because it allows the necessary deflections under seismic conditions.
0
FlexHead° Flexible Sprinkler
Connections Satisfy New Seismic
Code Requirements
Background of New
Code Requirements:
More than 90% of the
states in the U.S. are
adopting the
International Building
Code (IBC) that address,
among other things, the
installation of fire
sprinkler systems in
seismic zones. The code
is intended to neutralize
the probability of fire
sprinkler systems being
damaged and made
inoperable by seismic
activity, including ceiling
movement than can shear
sprinkler heads and/or
TYPtt ally, each,lnit consi`sts.of Pe n,PPie
a threaded pipe nipple:for.;
connecting to the maih or branch
feeder. line, a.flexible:hose in
stand#dflehgths;•a reduang fitting i"'_$pnpkler
thkAhe sprinkler head attachesao branchline''.:
and a mounting -6iaeket. Flexible connecting hose4n standard
lengths aUothehead to mw s inanydHeAonduringa?se,sinic event - -•
without rau;ing damage to Hie: ; .
spookier rystemr,
Mounting bracket 6dudng fitting
rk
Ceiling file
SpNokt, 14ad
h
r
disrupt the integrity of FlexHead Industries recently satisfactorily completed full-scale seismic qualification
arm -over connections testing at the Structural Engineering Earthquake Simulation Laboratory located at
from the branch lines. SUNY, University at Buffalo. Tests were conducted using the International Code Council
The IBC Code and ICC) acceptance criteria "ICC-ES AC-156 Seismic Qualification Testing of Nonstructural
Sprinkler Design in
Components". This is the first time a sprinkler component has been seismically certi-
fied using test criteria accepted by the ICC.
Suspended Ceilings: The
latest version of the IBC
defers to ASCE 7 for the sprinkler/ceiling design in
Seismic Design Categories 9SDC) C and D, E & F. In
Seismic Design Category C, suspended ceilings are to be
designed and installed in accordance with Ceilings &
Interior Systems Construction Association (CISCA)
recommendations for Zones 0-2; and sprinkler heads
and other penetrations shall have a minimum of 1/4-
inch clearance on all sides. In Seismic Design
Categories D, E & F, suspended ceilings are to be
designed and installed in accordance with CISCA
recommendations for seismic Zones 3 and 4 with some
additional requirements. Except where rigid braces are
used to limit lateral deflections, sprinkler heads and
other penetrations shall have a 2-inch oversized ring,
sleeve, or adaptor through the ceiling to allow for free
movement of at least 1 inch of ceiling movement in all
horizontal directions.
Flexible Sprinkler Connections Exceed IBC Code
Requirements: Flexible sprinkler connection provide
characteristics that exceed the most stringent seismic
code requirements. The flexibility of the hose allows
the head to move with the ceiling in any direction
during a seismic event without causing damage to
the sprinkler system. FlexHead Industries recently
satisfactorily completed full-scale seismic
qualification testing at the Structural engineering
Earthquake Simulation Laboratory located at the
University of Buffalo using the International Code
Council (ICC) testing standard "ICC AC-156
Seismic Qualification Testing of Nonstructural
Components". This is the first time a sprinkler
component has been seismically certified using
test criteria accepted by the IBC. FlexHeads were
installed in suspended ceilings meeting the code
requirements for Seismic Design Category C and
Seismic Design Categories D, E & F and were
subjected to the highest accelerations determined
for each Seismic Design Category. No damage to
the fire sprinkler system or suspended ceiling
system was observed, and the sprinkler heads
remained in their intended location during all of
the test performed.
EA I
C,
Friction Loss Data and Specifications
FlexHead Internal outlet Hose Assembly Equivalent Length of i" Maximum Rated
Model # Diameter Size Length ft(m) schedule 40 pipe Pressure
True -Bore FM Approval/UL Listing
2024 1 in 1/2 in. 2 ft (0.6 m) 3.5 ft (1.1 m)/17 ft (5.1 m)• 175 psi (1205 kPa)
2036 1 in 1/2 in 3 ft (0.9 m) - 4.8 ft (1.5 m)/22 ft (6.6 m)• 175 psi (1205 kPa)
2048 1 in 1/2 in. 4 ft (1.2 m) 6.8 ft (2.1 m)/24 ft (7.3 m)• 175 psi (1205 kPa)
2060 1 in 1/2 in. 5 ft (1.5 m) 8.5 ft (2.6 m)/25 ft (7.5 m)• 175 psi (1205 kPa)
2072 1 in 1/2 in. - 6 ft (1.8 m) 8.9 ft (2.7 m)/28 ft (8.4 m)• 175 psi (1205 kPa)
2024 - 1 in 3/4 in. 2 ft (0.6 m) 7.8 ft (2.4 m)/9 ft (2.7 m)• 175 psi (1205 kPa)
2036 1 in 3/4 in. 3 ft (0.9 m) 8.1 ft (2.5 m)/16 ft (4.8 m)• 175 psi (1205 kPa)
2048 1 in - 3/4 in. 4 ft (1.2 m) 17.9 ft (5.4 m)/21 ft (6.4 m)• 175 psi (1205 kPa)
2060 1 in 3/4 in. 5 ft (1.5 m) 19.9 ft (6.1 m)/22 ft (6.6 m)• 175 psi (1205 kPa)
2072 1 in 3/4 in. 6 ft (1.8 m) 24.3 ft (7.4 m)/25 ft (7.5 m)• 175 psi (1205 kPa)
FlexHead products are intended for use in hydraulically designed wet, pre -action, deluge or dry pipe sprinkler connections
per NFPA 13, 13R, and 13D guidelines. The hydraulic loss of the FlexHead connector needs to be included in the hydraulic
design calculations the same as a valve or fitting. Each FlexHead sprinkler drop has a 3" minimum bend radius per UL
guidelines, and a 7" minimum bend radius per FM guidelines.
Equivalent lengths are shown with 3 bends. Different values were obtained by FM and UL due to the differences
in minimum bend radius, testing protocol and calculation methods. Please see individual testing standards for
more information relative to friction loss (Equivalent Length of Pipe).
System Specifications
Sprinkler system final connections in commercial
ceilings shall be FlexHead model number as
manufactured by FlexHead Industries Inc.,
Holliston, MA USA (800) 829-6975 or (508) 893-9596,
fax (508) 893-6020 as approved by Factory Mutual
Research Corporation and Underwriters Laboratories.
Each FlexHead system includes ceiling mounting bracket
with hardware and welded, leak -tested 1" braided
FlexHead Flexible sprinkler drop. The Fire Protection
Contractor shall be responsible for the installation
of sprinkler head and the final connection, fill and
test of the FlexHead ceiling system to sprinkler
sub -main in accordance to NFPA, FM, UL, and state
and local guidelines.
FlexHead Ceiling Sprinkler System
Model Numbers
Model # 2024 2 ft. FlexHead sprinkler drop
Model # 2036 3 ft. FlexHead sprinkler drop
Model # 2048 4 ft. FlexHead sprinkler drop
Model # 2060 5 ft. FlexHead sprinkler drop
Model # 2072 6 ft. FlexHead sprinkler drop
NOTE. FlexHead products are compatible with
FM/UL and LPCB listed sprinkler heads.
Usage of Flexible Piping Systems
Contractor shall provide flexible piping connections
to sprinkler heads for both suspended and sheet -
rock ceilings. All flexible piping systems shall be
UL Listed and FM Approved or LPCB certified and
suitable for their intended use.
All flexible piping connections to include a fully
welded (non -mechanical fittings), braided, leak -
tested sprinkler drop with a minimum internal
corrugated hose diameter of 1 inch true -bore;
and a one-piece ceiling bracket with removable
attachment hub and self -securing integrated
snap -on clip -ends, for attachment to ceiling grid
without the need for a screw fastener.
Acceptable Manufacturer(s):
1. FlexHead series 2000 as manufactured by
FlexHead Industries of Holliston, MA USA (800)
829-6975 or (508) 893-9596, fax (508) 893-6020
in lengths of 2 ft to 6 ft.
RexHead Suspended Ceiling Detail
Sprinkler head
not included)
Each FM approved, UL listed, LPCB certified
unit is ready to install, pressure- and
leak -tested, and comes complete with
a flexible stainless steel hose and
mounting bracket with adjustable hub.
FlexHead Sheetroc:k Ceiling Detail
Sprinkler head
not included)
E
Hose Specification Sheet
Regular Model Elbow Model
1 inch NPT threads
T to ANSI B1.20.1 T
Typ. 304 SS Sch.
B 40 Pipe B
Weld per
ANSI/AWS
B2. -00
Typ. 304 SS
Braid Sleeve
Okla Typ. 304 SS
Corrugated Hose
i inch true -bore
internal diameter
A provides lower
friction loss
Typ. 304 SS
Braid to prevent
elongation and improve
pressure retention
Weld per
ANSI/AWS
B2.1 00
Typ. 304 SS
C
Typ. 304 SS outlet
spud 1/2 & 3/4 inch
female NPT threads
to ANSI B1.20.1
Moiled #
2024 24 3 4.5 6.75
2036 36 3 4.5 6.75
2048 48 3 4.5 6.75
2060 60 3 4.5 6.75
2072 72 3 4.5 6.75
0
D
0
Bracket Specification Sheet
Multiport Design (For use with T-bar grid and metal stud applications)
4) 2.50"
Adjustable Design (For use with T-bar grid, metal stud, and
Chicago grid applications): standard sizes are 16" and 24" long
2.375"
1.13 5"
2.60"
E
Testing and Approvals
FM Global Testing — Approval Standard FM1637
FlexHead' series 2000 stainless steel sprinkler connections
Hydrostatic Strength Test
A sample FlexHead was subjected to a hydrostatic
pressure of four (4) times the rated working
pressure of 175 psi (1205 kpa) to 700 psi (4825
kpa) for a period of five minutes. The assembly
showed no signs of rupture, cracking, permanent
distortion, or deterioration of performance
characteristics. The FlexHead successfully passed
this test.
Vibration Test
A sample FlexHead was secured to a vibration
table. The FlexHead hose was bent in a 90' angle
and pressurized to 90 psi (620 kpa) and the
mounting bracket and hose were then subjected to
a total of 25 hours of severe vibration conditions.
After the successful completion of the vibration
tests the sample was subjected to the hydrostatic
pressure test at 700 psi and showed no signs of
deterioration. The FlexHead successfully passed
this test.
Friction Loss (Equivalent length of pipe)
To determine the effect of the FlexHead to the
discharge coefficient of the sprinkler, the average
friction loss through the FlexHead shall be
equated to the theoretical length of nominal 1"
diameter schedule 40 sprinkler pipe which would
produce the same amount of friction loss. Please
see friction loss table.
Vacuum Test
A sample FlexHead was subjected to a vacuum
of 25 inHG for a period of five minutes. After
the successful completion of the Vacuum Test
the sample was subjected to the hydrostatic
pressure test at 700 psi and showed no signs of
deterioration. The FlexHead successfully passed
this test.
Pressure Cycling Test
A sample FlexHead was filled with water and bent
at a 900 angle and subjected to 20,000 cycles of
pressure varying from 0 psi (0 kpa) to 175 psi
1205 kpa) at a rate of approximately 6 cycles per
minute. After the successful completion of the
pressure cycling tests the sample was subjected to
the hydrostatic pressure test at 700 psi and
showed no signs of deterioration. The FlexHead
successfully passed this test.
Fatigue Test
A sample FlexHead was subjected to 50,000 cycles
of repeated flexing at a rate of 5 to 30 cycles per
minute per section 8.3 of ISO standard 10380.
After the successful completion of the fatigue test
the sample was subjected to the hydrostatic
pressure test at 700 psi and showed no signs of
deterioration. The FlexHead successfully passed
this test.
Head Deployment
A sample FlexHead installed in a suspended ceiling
was fitted with a sprinkler head and pressurized to
26-175 psi. The sprinkler head was then activated
by a heat source at various pressures, and the
sprinkler head deployed. The assembly showed no
signs of distortion or deterioration of performance
on the assembly or sprinkler head. The FlexHead
successfully passed this test.
E
FM
APPROVED
FLEXIBLE SPRINKLER HOSE WITH FITTINGS FOR COMMERCIAL SUSPENDED CEILINGS
Flexible sprinkler hose with threaded end fittings are for use in commercial suspended
ceilings. The flexible hoses are to be installed according to the manufacturer's directives.
Unless indicated, the hoses have a rated working pressure of 175 (1205 kPa).
Flexhead Industries, Inc. 56 Lowland St, Holliston MA 01746
Model NPT in.
7—
Hose Assembly length ft (m)
2024H 1/2 2 (0.6)
2048H 1/2 4 (1.2)
2060H 1/2 5 (1.5)
6 (1.8) 2072H 112
Model NPT in. Hose Assembly length ft (m)
2024/2024 75 1/2 / 3/4 2 (0.6)
2036/2036 75 1/2 / 3/4 3 (0.9)
2048/2048 75 1/2 / 3/4 4 (1.2)
2060/2060
2072/2072
75
75
1/2
112 /
3/4 --
3/4
5 (1.5)
6 (1.8)
Model NPT in. Hose Assembly length ft (m)
2024E 1/2 0.6)
2036E 1/2 3 (0.9)
2048E 1/2 4 (1.2)
2060E --•-- 1/2 --- 5 (1.5) -- -- _
2072E 1/2 6 (1.8)
The "H" designation indicates a pressure rating
of 300 psi (2070 kPa). Approval on the 2000H
series flexible metal sprinkler hose is limited
for use in commercial suspended ceilings, with
a ceiling bracket system manufactured by
FlexHead Industries Inc. The brackets are
identified below.
This is a standard flexible hose with a pressure
rating of 175 psi (1205 kPa). Approval on
these models of flexible metal sprinkler hose is
limited for use in commercial suspended
ceilings, with a ceiling bracket system
manufactured by FlexHead Industries Inc. The
brackets are identified below.
This is a standard flexible hose with a pressure
rating of 175 psi (1205 kPa). Approval on
these models of flexible metal sprinkler hose
incorporates a stainless steel elbow welded on
the outlet end of hose and are limited for use
in commercial suspended ceilings, with a
ceiling bracket system manufactured by
FlexHead Industries Inc. The brackets are
identified below.
The seven FlexHead Industries, Inc. Brackets are identified as follows:
Part Number
SP-24-BKT (1) SP = Single Port (1) = 1 Piece
SP-24-BKT (2) 2) = 2 Piece
MP-24-BKT MP = Multiport
MP-24-BKT-2
SP-06-TZ-BKT TZ = Tech Zone
AD-16-BKT-2 AD = Adjustable
AD-24-BKT-2
BKT = Bracket
24 = Length in inches of bracket
06 = Length in inches of bracket
16 = Length in inches of bracket
24 = Length in inches of bracket
M
Testing and listings
Underwriters Laboratory Testing — Listing Standard
UL1474
FlexHead* series 2000 stainless steel sprinkler connections
Hydrostatic Pressure Test
A sample FlexHead was subjected to a hydrostatic
pressure of five (5) times the rated working
pressure of 175 psi (1205 kpa) to 875 psi (6030
kpa) for a period of one minute. The assembly
showed no signs of rupture, cracking, permanent
distortion, or deterioration of performance
characteristics. The FlexHead successfully passed
this test.
Vibration Test
A sample FlexHead was subjected to hydrostatic
pressure of 500 psi (3.45 MPa). The FlexHead hose
was bent in a 900 angle and pressurized to 175 psi
1.21 MPa) and the mounting bracket and hose
where then subjected to a total of 60 hours of
vertical vibration and 60 hours of horizontal
vibration with the amplitude of 0.04 inch (1.02
mm) at a continuously varying frequency between
18 and 37 hertz. After the successful completion of
the vibration tests the sample was subjected to the
hydrostatic pressure test at 500 psi and showed no
signs of deterioration or leakage. The FlexHead
successfully passed this test.
Friction Loss (Equivalent length of pipe)
To determine the effect of the FlexHead to the
discharge coefficient of the sprinkler, the average
friction loss through the FlexHead connector shall
be equated to the theoretical length of nominal
1 inch diameter schedule 40 sprinkler pipe which
would produce the same amount of friction loss.
Please see friction loss table.
Mechanical Strength Test
A sample FlexHead was secured and subjected
to a torsion force with a torque of 60 pound -feet
81 Nm) applied to the outlet. After the successful
completion of the mechanical strength test the
sample was subjected to the hydrostatic pressure
test at 175 psi (1205 kpa) and showed no signs of
deterioration or leakage. The FlexHead successfully
passed this test.
0
High Temperature Exposure Test
A sample FlexHead was subjected to hydrostatic
pressure of 500 psi (3.45 MPa) and then subjected
to a temperature of 375° F (191° Q for a period of
90 days. After the successful completion of the high
temperature test the sample was subjected to the
hydrostatic test of 500 psi (3.45 MPa) for a period
of one minute and showed no signs of deterioration
or leakage. The FlexHead connector successfully
Passed this test.
Salt Spray Corrosion Test
A sample FlexHead was subjected to salt spray (fog)
connector test, per ASTM B117-94, for a period of
10 days and showed no signs of deterioration or
incipient corrosion. The FlexHead successfully passed
this test.
Water Hammer Test
A sample FlexHead was subjected to 3,000
applications of pressure pressure surges from 50-500
psig at a rate of 60 cycles per minute and showed
no signs of deterioration or leakage. After the
successful completion of the water hammer test the
FlexHead was subjected to the hydrostatic test of
500 psi (3.45 MPa) for a period of one minute and
showed no signs of deterioration or leakage. The
FlexHead successfully passed this test.
Freezing Test
A sample FlexHead was filled with water and
exposed to an atmosphere of 10 F (-29 Q for a
period of 24 hours and showed no signs of
deterioration or leakage. After the successful
completion of the freezing test the FlexHead was
subjected to the hydrostatic test of 500 psi (3.45
MPa) for a period of one minute and showed no
signs of deterioration or leakage. The FlexHead
successfully passed this test.
c @us
LISTED
VENREX5269
Flexible Sprinkler Hose Fittings Certified for USA and Canada
FLEXHEAD INDUSTRIES EX5269
LOWLAND IND PARK
56 LOWLAND ST
HOLLISTON, MA 01746 USA
Models 2024H, 2036H, 2048H, 2060H, 2072H, flexible sprinkler hose fittings having a 300 psi
rated pressure. For use with ordinary, intermediate and high temperature rated automatic
sprinklers.
Models 2024S, 2036S, 2048S, 2060S, 2072S flexible sprinkler hose fittings having a 175 psi
rated pressure. Fore use with ordinary, intermediate and high temperature rated automatic
sprinklers.
Models 2024 24 DAL, 2036 36 DAL, 2048 48 DAL, 2060 60 DAL, 2072 72 OAL, flexible sprinkler
hose fittings having a 175 psi rated pressure. Fore use with ordinary intermediate and high
temperature rated automatic sprinklers.
Modes 2024I, 2036I, 2048I, 2060I, 2072I flexible sprinkler hose fittings having a 175 psi rated
pressure. Fore use with ordinary, intermediate and high temperature rated automatic sprinklers.
Maximum number of bends, maximum bend angles and associated pressure loses are shown in
the manufacturers installation instructions.
Testing and Certifications
Loss Prevention Certification Board — Loss Prevention
Standard LPS 1261
FlexHead' series 2000 stainless steel sprinkler connections
Hydrostatic Pressure S02 Conditioning Test
Flexible hose will be subjected to 4 times the Flexible hose will be subjected to 4 times the
maximum working pressure for a period of one maximum working pressure after completion of the
hour. FlexHead successfully passed this test. S02 conditioning. FlexHead successfully passed this
test.
Elevated Temperature Test
Flexible hose will be subjected to elevated
temperature of 122F (50C) for 90 days, then
subjected to 4 times the maximum working
pressure. FlexHead successfully passed this test.
Sulphuric Acid Test
Flexible hose will be subjected to 4 times the
maximum working pressure after conditioning in
sulphuric acid. FlexHead successfully passed
this test.
Crushing Load Test
The flexible connection with the cover removed
shall be subjected to a crushing load of 100kg
applied evenly over a length of 50mm for 30s. The
connection shall not collapse or show signs of
permanent deformation in excess of 5% of any
appropriate dimension measured before the test.
FlexHead successfully passed this test.
Salt Spray Test
Flexible hose will be subjected to salt spray
conditioning in accordance to BSEN 60068-2-
53:1996 Test K6 Salt Mist Cyclic (Severity 1). Then
it will be subjected to hydrostatic test 4 times
maximum working pressure. FlexHead successfully
passed this test.
Dry Pipe Fire Test
A flexible assembly shall be pressured with air to 3
bar for 3 minutes. The flexible hose assembly shall
then be subjected to a fire test. The air pressure
shall be kept constant by venting. The flexible
hose must maintain integrity of the pipework
throughout the test. FlexHead successfully passed
this test.
Sprinkler head Activation Test
Flexible hose and bracketing system will be
installed to installation instructions into a 600mm
x 600mm ceiling tile. Sprinkler head will be
activated at 12 bar (175 PSI) and maintain
running pressure at 11 bar (160 PSI) for 2
minutes. The sprinkler head must remain in
position. FlexHead successfully passed this test.
Pressure Loss Test
To determine the effect of the flexible hose to the
discharge coefficient of the sprinkler, the average
friction loss through the flexible hose shall be
equated to the theoretical length of nominal 1"
diameter schedule 40 sprinkler pipe which would
produce same amount of friction loss. Please see
friction loss table.
Loss Prevention Certification
APPENDIX TO CERTIFICATE NO. 764a
FLEXHEAD INDUSTRIES INC.
56 Lowland Street, Holliston, MA 01746, USA
c ..
Model
Length
mm)
Nominal Size / Connection
Max. Working
Pressure (bar)
LPCB
Ref. No. Supply Outlet
2024 600
R1 (1" NPT) cr (1"
BSPT)
External thread
RcY: or Rc'/. ('/2" or
NPT) or ('/:" or'/." BSP
Internal thread
12 764a/01
2036 900
2048 1200
2060 1500
2072 1800
2024H 600
R1 (1" NPT) or
1" BSPT)
External thread
Rc%or Rc% (Ys' or
NPT) or (%i' or'/." BSP
Internal thread
20 764a/02
2036H 900
2048H 1200
2060H 1500
2072H 1800
This certificate is valid until withdrawn by LPCB.
To check the validity and the authenticity of this certificate please
visit our website www.RedSookLive.com or contact us.
Signed on behalf of the LPCB
Date of Issue 21 June 2006
Name: Simon Bird
LPCB is part of BRE Certification Ltd., Garston, Watford WD25 9XX. Tel +44 (0)1923 664100
Fax +44 (0)1923 664603 wm,4.RedBookLive.com
This certificate remains the property of BRE Certification Ltd and is issued subject to terms and conditions
and is maintained and held in force through regular surveillance activities.
BF667 Revision 0. 03 January 2006 Page 2 of 3 ea'BRE Certification Ltd, 2006 14
APPHO-afibil N0. `OPA-:0671-
FMAPPRO"VAL AND. Vt FIRE SPRINK-11 Eg CONNECTIONS,
has -be6u,px-a-m'inedfbt con'formanecto the!turrotit ft- dbbid&bVthb;0f-rlde-,bfrequirements
Statewide Fl.ealth Planning -and DdVeldprilient, Facilities Development Division..'
Signed this Thursday., August 12, 2004.
STATTE '.OP CALIFORNIA, BEALTHA. ND, 14UMAN " SERVICE&APE'NCY
OFFICE OF STATEWIDE HEALTH PLANNING AND DEVELOPMENT
FACILITIES DEVELOPMENT DIVISION.
Pro'gram Adniihifi(atot
Thisapproval mWtbe-refiewed every three (3) yeArs. Other c6nditibn-- requiringfthewad, are
b
app e cl e -164. ebodA_ s, n ,r gplations,
21, Changes in the: rnamffactui,4 prpduct'(fixe&equipfheTlt).
3. Changes in°ftie method's of anchorage or Ahch. pf'& deVide§'
List -of Apptoved- b0c'u- ment§:
4 ShedtNos- Sheet I 6f2.thrbu . i-Shedt l4f2:
0
0
W rsc
W;WA U, Us alp.. a r 94-
WOUSTRIES.
XHEAD SPRINKLER.NNEC00 TIONFLE'
72E-L i. 20.01 20M.0 -3. 04A .00i
MAa.PRE-AP0RQVtDD - ETAIL
Offide,of Stdftidtfle'afth Planfilog,and Development
ANQ. . RM.-RI. AGE, P.R&APPROVAl.
EX15TINO.K.ATER
PER NFPA-6UIVE LINES
B-( &*INt92 OF W56MP)
F-LP_iEAD BRACKET
SNAPS ONTO
T-BAR CSBLIN6
T-BAR 6"L' (
EW'EN61kEM
r'.6. lit.
6 A
16 6K 6ALVMIZED
SHEET HET4
26 GA. .&LVANIZED
SHEET METAL
SPRINKLER WV
GENERAL .146TES.
1. FORGES ME DTERMINW PER 2661 CE5G,5E6T16N .1632A, Ga-;:- .66,6 p = 1.0,1p = 1:5, R p = 3.6 HORIZONTAL
FORGE (W =aq4vi VERTICAL
FORGE. ENv) ON 2-
ENGINEER-6F'RE66RD FOR THE, BUILDING 5HALL PROVIDE SUPPORT' 5TRXTUME
PE516NED TO. SUPPORT ka6w5 AND FORCES SHOW A
p o., V P_ D Fixed +
qu CA— h--- OPA=
602 Atigtist 16, 2664. Voila
for 3 E(
b
Ifiulnll•i16
ftt`tVirldllrZFri
C&US Underwriters Laboratories Inc.'
LISTED
June 21, 2001
FlexHead Industries
Mr. Norm MacDonald
56 Lowland St.
Holliston, MA 01746
Our Reference: File EX5269
Subject: FlexHead Flexible Sprinkler Hose Fittings Installed Onto Dry Wall
Ceiling Grid
Dear Mr. MacDonald:
This letter is in regard to the subject.
Base upon review of the FlexHead UL Listed flexible sprinkler hose fitting system,
installation onto a dry wall ceiling grid is acceptable when the ceiling -mounted
bracket is screwed to a rigid surface. Self -tapping screws are used to affix the
FlexHead mounting bracket to the surface, using the four ports provided which are pre -
drilled onto the mounting bracket.
Very truly yours,
EMIL W. MISICHKO (Ext. 42036)
Engineering Group Leader
Conformity Assessment Services
Department 3011CNBK
Emil W. Misichko@us.ul.com
G
A not -for -profit organization
dedicated to public safety and
committed to quality service
l
N
Ak
a„rsevtN''.
o,
Flexhead Industriie s/`'
56•Lowland.Str eft
Holliston, MA 01746
Attn: Norm MacDonald
Subject: IBC/ASCE 7 Compliance
Dear Mr. MacDonald,
EQVIPAILNTANCHORAGE& SEISrMICENGINEERMG
SSRHurrUngtonDiice, Suite4277
Arcadia, CA 91006
626) 445-0520
Far. (626) 445.2947
www equipmentanchone com
May 18, 2004
I have reviewed the material that was sent to me regarding the flexible sprinkler drops, your company
manufactures. As you are aware, our firm focuses its efforts solely on seismic restraint of equipment and
ceiling systems. We are quite impressed with the freedom of movement that your solution provides.
Regarding ASCE 7; in section 9.6.2.6.2.2 the acceptance criteria states that all sprinkler heads must have a
horizontal freedom of movement of at least one inch in every direction. Your flexible sprinkler drops not only
provide far more than the specified one inch, but they also allow vertical motion and rotation as well. It is
quite apparent that the use of this product would not only conform to the requirements of ASCE 7 but exceed
them as well.
The FlexHead product is satisfactory and complies with the intent of the provisions of code section 1621 of
the IBC and ASCE? subsections 9.6.2.6.2 and 9.6.2.6.2.2 with reference to sprinkler heads having a
minimum clearance on all sides; and the product, for the purpose intended, meets or exceeds these provisions
of these in quality, strength, effectiveness, fire resistance, durability and safety.
Yours Very truly,
Richard 13. La 13ne P.E., Principal
EASE Incorporated
UB J:1`D 11;5
RO, P 0,of E4uilCings.
NY Oq
iS
bdie...4ppAi'dot;
bcmoio Gottfried; Ff.E.
212.566.3282
212i.566:3646 fax
9na
bate; 16Zv64•
Eh-clo's-ed 's a fihAl'6ffi6i.Al: s.igndd copy of NMA accbptanct of your pf6duct(s),
may as . w' Nit, ith you'u may of your products) acceptance in NeA
Y.gtk V
This document toget4eir, witfi.,pr6oer labeling an, installation in accordance with New
Yofk City -bul; lding,Codb'vvi 11 enable the 'inspector to know -that the product(s) installed is (are) -
Ali shipments and deliveries: of accepted materials to the job -site are required -to be:
libeled or tagged in accordance with the format below'
Accdpt0d,For,Usd-
City. of New, York
Department of-BujIdings
EAR
corboAhy Ndiri
truly yours, 211c,
b6fiald-'Ootdried, PE,
Director
Materials and:Equipment Acceptance Divis ion,
FlexHead Industries, Inc. warrants that its products will specifications, instructions or recommendations,
be free from defects in materials and workmanship under including, without limitation, our
normal conditions of use and service for a period of one
year from date of sale. Our obligation under this
warranty is limited to repairing or replacing any product
that is returned to us with transportation charges
prepaid within one year after the date of original sale
and that our examination shows to our satisfaction to
have been defective in materials or workmanship under
normal conditions of use and service. The decision as to
whether to repair or to replace any product shall be
made by us, and any repair shall be made at our facility.
Notwithstanding the foregoing, the following are
specifically excluded from the coverage of this warranty:
a) the sprinkler head of any FlexHead Industries, Inc.
product, but FlexHead Industries, Inc. hereby assigns to
the original purchaser of any such product the right to
enforce the warranty, if any, issued by the manufacturer
of such sprinkler head; (b) defects resulting from
ordinary wear and tear, including, without limitation,
the replacement of the so called poly bag components of
any FlexHead Industries, Inc. product; (c) products that
have been altered in any manner by the buyer or by
anyone other than FlexHead Industries, Inc.; (d)
products that have been subjected to misuse, abusive
use, or damage by accident or casualty; (e) products
that have been installed or used in a manner contrary to
our specifications, instructions or recommendations, (f)
products that have been installed or used in a manner
that is not in compliance with all applicable
requirements of any code, law, regulation or rule of any
federal, state or local governmental or industry
authority; and (g) products that have not been
inspected and maintained in accordance with our
recommendations as to following the inspection
and maintenance standards published by Factory
Mutual Research Corporation (FMRC) and the
National Fire Protection Association (NFPA); and
h) products that have been affected by
Micro biologicaRy Influenced Corrosion (MIC). This
warranty is not assignable and shall benefit only
the original purchaser of a FlexHead Industries,
Inc. product. If any provision hereof or any portion
of any provision shall be held invalid, the
remainder of this Limited Warranty shall not be
affected thereby, and all provisions of this Limited
Warranty shall remain valid and in full force and
effect to the fullest extent permitted by law. THIS
WARRANTY IS IN LIEU OF ALL IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY AND
WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE. NOTWITHSTANDING ANY PROVISION TO
THE CONTRARY HEREIN OR ANY APPLICABLE LAW
TO THE CONTRARY, IN NO EVENT SHALL FLEXHEAD
INDUSTRIES, INC. BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES UNDER ANY
CIRCUMSTANCES WHATSOEVER, WHETHER ARISING
FROM ANY BREACH OF THIS LIMITED WARRANTY OR
OTHERWISE ARISING FROM OR IN CONNECTION
WITH THE USE OR OPERATION OF, OR ANY DEFECT
IN, ANY FLEXHEAD INDUSTRIES, INC. PRODUCT, OR
OTHERWISE. The risk of damages from any breach
of warranty with respect to injury to any person
will be born by the purchaser of FlexHead
Industries, Inc. product.
0 Your security is our business.
FlexHead Industries was founded in 1992 to help engineers, builders
and owners increase the safety of their buildings. Our patented
sprinkler connection technologies show
that it's possible to comply with codes
cost-effectively. We're proud to help
reduce the risks of property damage and
loss of life in a wide variety of buildings,
domestically and world-wide.
FlexHead manufactures
sprinkler connections for
all types of applications
including:
Commercial Exhaust ducts
Government Aerospace
4 Offices Z, Automotive
Q Restaurants Biotechnology
6 Retail Electronics
0 Schools Forest products/
Cleanrooms paper pulp
o: Biotechnology
Laboratories
o Electronics
Petrochemical
High -end commercial
to Pharmaceuticals
ceilings e Restaurants
4, Pharmaceuticals V Semiconductors
Semiconductors Steel manufacturers
Institutions
Concrete penetrations
for si lewall and
pendant applications
r Correctional centers
Mental health facilities
r
Seismically
qualified.
FlexHead connections allow
for independent movement
between sub -mains and
ceilings. They're the only
flexible sprinkler connection
to be qualified for use in
Seismic Design Categories
C, D, E and F.
Schedu1em10"/Schedu1e=40"
Fully Listed and FM Approved Sprinkler Pipe
When you specify Schedule- I O/Schedule-40 sprinkler pipe you get a UL listed and FM approved product. Although these
products do not require separate approvals, Schedule-10/Schedule-40 gives you the extra quality assurance you demand.
Our Sch-10 (1'/,"- 8") pipe and Sch-40 (1"- 2'/2") pipe have passed the same thorough lab testing as our other listed pipe
products, and receive periodic mill inspections from both 11L and FM agents to ensure consistent quality.
Galvanized Pipe
Schedule-10/Schedule-40 product can be
hot -dip" galvanized to meet FM
requirements for dry systems in
accordance with the zinc coating
specifications of ASTM A-123.
Our advanced formula mill coating of-
fers a clean, durable surface. It is also
paint -ready for custom color applications
without special preparation.
The internal surface of all black Allied
Tube & Conduit Fire Sprinkler pipe'
products up to 4.5000" in diameter is
coated with our new Antibacterial For-
mula, "ABF'. In scientific laboratory
test, ABS proved to have superior resis-
tance to microbial colonization of pipe
walls, thereby delaying or possibly pre-
venting the onset of Microbiologically
Influenced corrosion (MIC) when the
First Sprinkler System is first installed.
American Made
Meets "Buy American" requirement
and is available through distributors in
the USA, Canada and Mexico.
Schedule-10/Schedule-40 pipe are in
compliance with the following:
ASTM A-135, and NFPA 13. Both pipe
products have a working pressure rating
of 300 psi maximum and also meet the
stringent requirement for the following
tests:
Welded Outlets
Hydrostatic Pressure
Side Wall Rupture
Vibration Test
4t Specifications
NPS Nomio.l I.D. Wt. WL (11120 Filled) Pa/ WWft (21') WWR (24') WWO (25'
In; mm In; mm Lbs/ft KVm Lb&ft Kym Lilt Lbs; Kg Lbr; Kg Lbs; Kg
1' 1.049 1.680 2.05 70 2,470 2,822 2,940
25 26.6 2.5 3.05 70 1,120 1,280 1,334
1'/' 1.380 2.270 2.93 51 2,431 2,778 2.894
32 35.1 4.36 4.36 51 1,103 1,260 1,313
1'/i' 1.610 2.720 3.61 44 2,513 2,872 2,992
40 40.9 4.0 5.37 44 1,140 1,303 1,357
2' 2.067 3.650 5.13 30 2.300 2,628 2,738
50 52.5 5.4 Z63 30 1,043 1,192 1,242
2%* 2.469 5.790 7.86 19 2,310 2,640 2,750
65 62.7 8.6 11.73 19 1,048 1,197 1,247
Sch-10 Specifications
minal I.D. WL WL (N20 Filled) Pal WVUft (21') Wtl M (24') WWO (25'
In; mmLbOt-Kp/m LbsTCKg/m Lift Lbs; Ky Lbr, Kg Lbs; Kg712791.097 1.400 1.81 91 2,675 3,053 3,185
2.1 2.70 91 1,213 1,385 1,445
1% 1.442 1.810 2.52 61 2,319 2.664 2,760
32 36.6 2.7 3.75 61 1,052 1,208 1,252
1'Ih, 1.682 2.080 3.04 61 2,664 3,045 3,172
40 42.7 3.1 4.52 61 1,208 1,381 1,439
2' 2.157 2.640 4.22 37 2,051 2,344 2,442
50 54.8 3.9 6.28 37 930 1,063 1,108
2'/i' 2.635 3.530 5.89 30 2,224 2,542 2,648
65 66.9 5.3 977 30 1,009 1,153 1,201
T 3.260 4.330 7.94 19 1,728 1,975 2.057
80 82.8 6.4 11.82 19 784 • 896 933
4' 4.260 5.610 11.78 19 2,238 2,558 2.665
90 108.2 8.3 17.53 19 1,015 1,160 1,209
5' 5.295 7.77 17.33 10 1,632 1.865 1,943
125 134.5 11.56 25.80 10 740 846 881
6' 6.357 9.290 23.03 10 1,951 2,230 2,322
150 161.5 13.8 34.27 10 865 1,012 1,053
8' 8.249 16.490 40.15 7 2,424 2,770 2,885
200 209.5 24.5 59.75 7 1,100 1,256 1,309
tyCO/FlowConvol n allied
TUBE & CONDUIT
@ t=nn UDC
Listed Approved Listed
16100 S. Lathrop • Harvey, IL 60426 Customer Service:
11350 Norcom Rd. • Philadelphia, PA 19154 800) 882-5543
2525 N. 27 th Ave. • Phoenix, AZ 85009 Fax 708-339-1806
S5-3
Threaded Fittings
Tyco Fire Products --- www.tyco-grooved.com CENTRAL
451 North Cannon Avenue, Lansdale, Pennsylvania 19446 --- USA -.000now—
Customer Service/Sales: Tel: (215) 362-0700 / Fax: (215) 362-5385 Grooved Piping ProductsTechnicalServices: Tel: (800) 381-9312 / Fax: (800) 791-5500
General
Description
U FM See Fire Protection
Submittal Sheet for
pressure rating and Listing
and Approval information
Ductile Iron threaded fittings (with
the exception of California Tees and
Street Elbows) conform to ANSI
1316.3. They are higher in strength
and more corrosion resistant than
cast iron fittings. The additional
strength is provided by the ductile
properties making up the fitting. This
is accomplished by adding
magnesium while the iron is being
poured into it final cast shape. This
provides an advantage as the
fittings are not as susceptible to
leaks or cracking and they are also
lighter than standard cast iron.
Caution: Installers who have not used
ductile iron threaded fittings before
should be instructed that the fittings
are stronger than the pipe and over -
tightening the fitting can create leaks
and cause damage to pipe threads. In
general, there is about one-half turn
difference between cast iron and
ductile iron fittings. Apply Teflon tape
or high quality pipe joint compound on
the male pipe threads and tighten two
to three turns beyond hand tight. If
you are using an automatic make -on
machine, please exercise caution in
setting your machine to the proper
parameters prior to tightening fittings
onto the male pipe threads.
Technical
Data
Figures: 811, 812, 813, 814, 815,
816, 817, 818, 820, 825, 827,
830, 719, California Tees, and
Street Elbows
Sizes: 1/2" - 21/2"
Maximum Working Pressure:
800 Series, California Tees,
and Street Elbows: 300 psi
Figure 719: 250 psi
Approvals: UL, and FNI
Note: See Fire Protection
Submittal Sheet for exact
Listing/Approval information.
Manufacture Source:
Imported
Material:
Ductile Iron, conforming to
ANSI B16.3 (Note: Figure 719
Plugs are constructed of Cast
Iron)
Thread: N.P.T.
rAInstillation
Apply Teflon Tape or high quality
pipe joint compound on the male
pipe threads and tighten two to
three turns beyond hand tight.
See caution in first column)
Ordering
Procedure
Ordering information: When placing
an order, indicate the full product
name. Please specify the quantity,
figure number and size.
Availability and Service: Grooved
Piping Products, valves, accessories
and other products are available
throughout the U.S., Canada, and
internationally, though a network of
distribution centers. You may write
directly or call 215-362-0700 for the
distributor nearest you.
Care and
Maintenance
The owner is responsible for the
inspection, testing, and
maintenance of their fire protection
system and devices in accordance
with the applicable standards of the
National Fire Protection Association
e.g., NFPA 25), in addition to the
standards of any authority having
jurisdiction. The installing contractor
or product manufacturer should be
contacted relative to any questions.
Any impairment must be
immediately corrected.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a
qualified Inspection Service.
No. 21-3.0
Figure 811
90° Elbow
Size
Inches
A
Inches
B
Inches
Part
Number
Weight
Lbs.
Box
0ty.
1/2 11/8 Me 86206 0.24 240
3/4 15/16 3/4 86205 0.40 120
1 11/2 13/1s 86200 0.64 70
1'/4 13/4 1'/16 86201 1 0.95 40
1'h 11 As 13/,e 86202 1.24 30
2 21/4 11/2 86203 1.74 20
2'/2 211/16 19A6 86204 3.28 10
p
r
Figure 812 '
901 Reducing Elbow
IA
Size
Inches
A
Inches
B
Inches
C
Inches
D
Inches
Part
Number
Weight
Lbs.
Box
Oty.
3/4 x1/2 13/16 13/18 5/8 5/s 86342 0.33 160
1 X '/2 11/4 13/8 9/16 13/16 86210 0.44 110
1 x 3/4 13/8 1'/1e 16 e 86211 0.53 90
1'/4 X '/2 15/16 1 1'/2 5/8 15/16 86212 0.64 75
11/4 x 3/4 1'/16 15/8 3/4 1'/16 86213 0.75 60
11/4 X 1 19As 1 W16 7/8 1 86214 0.77 55
11/2 x 3/4 11/2 13/4 3/4 13/16 86221 0.95 45
1'/2 x 1 15/a 113/16 e 1'/e 86215 0.99 40
1'/2 x 1'/4 113/16 1'/8 1'/8 13/16 86216 1.14 35
2 x 3/4 15/8 115/1e e 13/6 86217 1.39 30
2 x 1 13/4 2'As 2 15/16 86218 1.58 25
2 x 11/2 2 23/16 1'/4 17/16 86220 1.67 20
2'/2 x 2 23/e 25/8 11/4 17/a 86262 3.01 15
Figure 813
45° Elbow
Figure 814
Tee
A B Part Weight Box
Inches Inches Inches Number Lbs. City.
1/2 7/8 3/a 86780 0.22 250
3/4 1 '/16 86781 0.33 150
1 1'/a 17As 86280 0.48 90
1'/4 15/,s 5/s 86281 0.73
M501'/2 1'/16 "/16 86282 0.9321 "/16 15/ts 86283 1.552'/2 115/16 1 86782 2.70
Size
Inches
Size
Inches
A
Inches
B
Inches
Part
Number
Weight
Lbs.
Box
Oty.
2 1'/8 9/16 86340 0.33 150
3/. 15/16 3/4 86341 0.50 90
1 1'/2 3/16 86230 0.85 60
11/4 13/4 1'/t6 1 86231 1.30 35
1'/2 1 t5/16 13/te 86232 1.63 24
2 2'/4 1'/2 86233 2.63 12
2'/2 2"/16 19/16 86234 4.55 8
T -
E 1- lI F
Figure 815 {- -
o -
Reducing Tee I '
I- - -
Size
Inches
A
Inches
B
Inches
C
Inches
D
Inches
E
Inches
F
Inches
Part
Number
Wt.
Lbs.
Box
Oty.
3/4 X 3/4 X Vz 13/16 13/16 11/4 5/e 5/8 1s 86235 0.46 95
3/4 x 3/4 x 1 1'/16 1'/16 13/8 8 As 86755 0.68 65
1 x'/2 x 1 172 13/s 1'h 13/,s 3/1e t3/16 86236 0.70 55
1 x 3/4 X1/2 11/4 13/16 1 13/e I Vie 5/8 17/16 86756 10.631 80
1 X 3/4 X 3/4 13/8 15/16 17/16 11/16 3/4 a 86757 0.68 65
1 x 3/4 x 1 1'h 1'/Is 1'/2 13/te a 13/1s 86237 0.77 55
1 x 1 x'/2 1'/4 1'/4 13/8 9/16 9/18 t3/16 86238 0.66 65
1 x 1 x 3/4 13/8 13/8 1'/,a 1e 1s a 86239 0.73 60
1 x 1 x VA 111/Is 1 W18 19/16 1 1 86240 0.97 45
1 x 1 x 1'/2 113/16 113/16 15/e I 1'/e 1'/a I % 186241 1.14135
VA x 1 x'/2 115/16 1'/4 19/16 5/8 9/16 1 186242 0.81 50
VA x 1 x 3/4 1'/16 13/8 15/8 3/4 W19 1'/ts 86243 0.90 50
1'A x 1 x 1 19/te 1'h 1 "/Is a t3/,s 1 86244 1.03 45
11/4 x 1 x 11/4 13/4 111/16 13/4 1'/16 1 1'/te 86245 1.10 40
11/4 x 1 x 11h 11/e 113/16 113/16 13/16 11/5 1'/16 86246 1.43 30
11/4 x 11/4 x'/z 13/8 13/e 1 19/18 1 W16 As 1 1 86247 10.871 45
1'/4 x 1'/4 X 3/4 11/16 11/16 15/a 3/4 3/4 1'/16 86248 0.96 45
1'/4 x 174 x 1 19/1e 19/1e 1 "/Is e a 1 86249 1.10 40
1'/. x 1'/4 x V/2 1'/e 1'/8 113/16 1 i3/16 113/1e 1'/ts 86250 1.50 30
11/4 x 11/4 x 2 21/8 21/e 2 17/16 17/16 1'/8 86251 2.00 24
1 /2 x 1 x'h 17/Is 1 Me 1 "/,s 1s 5/a 17a 86252 0.97 40
1'12 X 1 X 3/4 1'/2 13/e 13/4 3/4 W16 13/16 86253 1.14 40
1V2x 1 x 1 15/e 1'/2 113/1s 7/8 17/,s 1'/s 86254 1.14 30
11/2 x 1 x 11h 115/16 113/16 115/16 13/1s 11/8 13/16 86255 1.52 30
11h x VA x'/2 0111 15/w 1 "/1s ts 5/e 1'/a 86257 1.03140
1 '/;-1 X 1 '/4 X 3/4 1'12 11/16 13/4 3/4 3/4 13/,s 86258 1.10 40
1'h x 1'/4 x 1 15/8 19/16 117/16 7/8 VA 86259 1.31 30
11/2 x 11/4 x 2 23/1s 21/a 2 1'/16 17/16 1'/4 86260 1.94 20
1 V.2 x 1'/2 x'h 1'/16 1'/16 1 W16 WI6 AS 1'/e 86261 1.14 35
1'/2 x 1'/2 x3/4 172 1'/2 13/4 3/4 3/4 13/,6 86262 1.23 35
1'h x 1'/2 x 1 15/e 15/e 1 t3/16 7/9 a 178 86263 1.38 30
11/2 x 11/2 x 11/4 1 11/16 113/16 1'/8 1'/1e 11/16 13/16 86264 1.50 30
1'12 x 1'/2 x 2 23/18 23/16 2 17/16 17/16 1'/4 86265 2.00 20
2 x 1 x 2 2'/4 2 2'/4 1'h 15/16 1'/2 86266 2.18 15
2 x 11A x 2 21/4 21/s 21/4 1'/2 1'/16 1'/2 86267 2.31 15
2 :(1'/2 x'/2 11/2 11/ts 1 % 3/4 16 15/16 86268 1.50 30
2:< 1112 x 3/4 15/s 1'/2 115/16 e 3/4 13/e 86269 1.61 1 25
2 x 11/2 x 1 13/4 15/s 2 1 7/8 15As 86270 1.65 20
2x11/2X1112 21/te 115/18 23/18 15/16 13/16 17/ts 86272 2.03 20
2 x 11/2 x 2 21/4 23/16 2'/4 1'/2 1'/,s 1'/2 86273 2.37 15
2 x 2 x'/2 1'/2 11h 17/8 3/4 3/4 15/le 86222 1.50 30
2 x 2 x 3/4 15/8 15/e 1 "As s e 13/s 86223 1.67 20
2 x 2 x 1 13/4 13/4 2 1 1 15/t6 186224 1.91 20
2:(2 x 11/4 1'/s 11/8 21/8 1'/s 1'/a 1'/ts 86225 2.05 20
2:(2 x 1112 2 2 23/16 1'/4 1'/4 1'/2 86226 2.11 15
2:(2 x 21h 25/9 25/s 23/a 13/4 17/8 17/16 86227 3.67 10
2'/2 x 2 x 3/4 13/4 15/e 25/16 5/9 7/8 13/4 86274 2.22 15
2-
Figure 816
Reducing Coupling
1
B
jr----- ,
Size
Inches
A
Inches
B
Inches
Part
Number
Weight
Lbs.
Box
Oty.
3/4 x'/2 13/4 A6 86772 0.38 240
1 x '/2 1 W16 12 86228 0.38 200
1 x 3/4 13/4 2 86229 0.53 110
F
A^A
D
Figure 817 c
Cross c
D
Size
Inches
A
Inches
B
Inches
C
Inches
D
Inches
Part
Number
Weight
Lbs.
Box
Oty.
1 11/2 11/2 t3/16 t3/16 86284 0.97 45
11/4 13/4 13/4 1 V16 1'/16 86285 1.59 25
1'/2 115/16 116/16 13/16 13/16 86286 1.89 20
2 2'/4 2'/4 1'/2 1 1'/2 J 86287 1 2.93 10
1'A x 1'A x 1 x 1 1 "/16 1 9/16 1 7/6 86289 1.25 30
11/2 x 11/2 x 1 x 1 1 t3/16 16/a 11/,6 1t6/,6 86322 1.48 24
2 x 2 x 1 x 1 2 13/4 1'/4 1'/16 86291 2.64 10
I -- fl I
Figure 818 I B A
Straight Coupling --- --
Size
Inches
A
Inches
B
Inches
Part
Number Wrench
Weight
Lbs.
Box
Oty.
1/2 13/8 6/I6 72779 1'/a 0.18 360
3/4 16/8 6/16 72778 13/6 0.26 200
1 13/4 Ye 72755 1 "/16 0.44 110
1'/4 2 9/16 72754 1 2 1 0.54 1 75
1'/2 23/16 3A 72753 2'/4 0.71 60
1'/a 72752 23/4 1.15 30bk2% 3 3/4 72758 1 33A 2.29 18
Figure 820
Cap
Size
Inches
A
Inches
Part
Number
Weight
Lbs.
Box
Oty.
z e 72776 0.15 500
3/4 1 72777 0.22 300
1 13/16 72824 0.33 180
1'/. 1 15/16 72756 0.54 110
1'/2 13/a 72822 0.68 80
2 11/2 72823 0.96 45
21/2 13/4 72825 1.80 25
Figure 825
Extension Piece
Figure 827
Hex Bushing
Size
Inches
A
Inches
Part
Number
Weight
Lbs.
Box
Oty.
1/2 x 1'/2 11/2 72751 0.20 300
112 x 2 2 72980 0.27 250
3/4 x 11/2 11/2 72981 0.22 250
3/4 x 2 2 1 72982 0.31 200
Size
Inches
A
Inches
Part
Number
Weight
Lbs.
Box
Oty.
1 x '/2 1'/16 72726 0.22 280
1 x 3/4 1'/16 72762 0.18 280
1'/4 x 1 13/16 72763 0.31 150
11/2 x 1 11/4 72757 0.53 1100
11/2x11/4 11/4 72764 0.35 100
2 x 1 13/8 72759 0.75 80
2 x 1'/4 13/a 72761 0.69 80
2 x 11/2 13/a 72775 0.62 80
Figure 830 1
n
Brass Seat Union - --
Figure 719
Cast Iron Plug
Size
Inches
A
Inches
B
Inches
Part
Number
Weight
Lbs.
Box
Oty.
1/2 1'/e 17/16 86207 0.47 110
3A 2 15/16 86275 0.66 80
1 23/16 13/16 86276 1.08 50
4 2'/2 1'/16W86277 1.54 351'/2 25/e 13/16 2.03 25
2 3'/a 16/a 3.15 18
Size
Inches
A
Inches
Part
Number
Weight
Lbs.
Box
Oty.
1/z 16/16 86292 0.10 500
3/4 1'/s 86293 0.18 300
1 1'/4 86294 0.28 200
1'/4 13/a 86295 0.50 110
1'/2 1'/16 86296 0.70 80
2 1'/2 86297 0.90 45
3-
Street Elbows
Ilull / II IIIII
IIIIIIIIII IIIIIIIII
Size
Inches
A
Inches
B
Inches
C
Inches
Part
Number
Weight
lbs.
Box
Oty.
1 x 'h 1'/2 A 3 42003 0.70 80
1 x 1 1'/2 A 3 42002 0.90 60
Limited
Warranty
Products manufactured by Tyco
Fire Products are warranted solely
to the original Buyer for ten (10)
years against defects in material
and workmanship when paid for
and properly installed and
maintained under normal use and
service. This warranty will expire
ten (10) years from date of
shipment by Tyco Fire Products. No
warranty is given for products or
components manufactured by
companies not affiliated by
ownership with Tyco Fire Products
or for products and components
which have been subject to misuse,
improper installation, corrosion, or
FF
California Tees r
L
Size
Inches
A
Inches
B
Inches
C
Inches
D
Inches
Part
Number
Weight
lbs.
Box
Oty.
1 x '/2 x 1 172 a 3 3/4 42000 0.95 50
1 x 1 x 1 1'/2 A 3 3/4 42001 0.95 45
which have not been installed,
maintained, modified or repaired in
accordance with applicable
Standards of the National Fire
Protection Association (NFPA),
and/or the standards of any other
Authorities Having Jurisdiction.
Materials found by Tyco Fire
Products to be defective shall be
either repaired or replaced, at Tyco
Fire Products' sole option. Tyco
Fire Products neither assumes, nor
authorizes any person to assume
for it, any other obligation in
connection with the sale of products
or parts of products. Tyco Fire
Products shall not be responsible
for sprinkler system design errors
or inaccurate or incomplete
information supplied by Buyer or
Buyer's representativE.S.
IN NO EVENT SHALL TYCO FIRE
PRODUCTS BE LIABLE, IN
CONTRACT, TORT, STRICT
LIABILITY OR UNDER ANY
OTHER LEGAL THEORY, FOR
INCIDENTAL, INDIRECT,
SPECIAL OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT
LIMITED TO LABOR CHARGES,
REGARDLESS OF WHETHER
TYCO FIRE PRODUCTS WAS
INFORMED ABOUT THE
POSSIBILITY OF SUCH
DAMAGES, AND IN NO EVENT
SHALL TYCO FIRE PRODUCTS'
LIABILITY EXCEED AN AMOUNT
EQUAL TO THE SALES PRICE.
THE FOREGOING WARRANTY IS MADE
IN LIEU OF ANY AND ALL OTHER
WARRANTIES EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE.
General Notes: It is the Designer's responsibility to select products suitable for the intended service and to ensure that
pressure ratings and performance data is not exceeded. Never remove any piping component nor correct or modify any
piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified
to be compatible for the specific application.
tgCOlFlowControll Tyco Fire
Products Printed U.S.A. 10-01
www.simplexgrinnell.com
2007 SimplexGrinnell LP All rights reserved. .
atepPrintedinU.S.A. Simple 6rinne®®
MC100-1-004
O Y®f77 iY ®®6LivL
0207 BE SAFE.